Showing results: 4726 - 4740 of 7336 items found.
-
PXD731x/70xx -
VX Instruments GmbH
Digitize high-resolution waveforms with the fully isolated PXD Series digitizers. Minimize interference and measure "in-circuit" within circuits. Measurement errors are reduced by a high input impedance.
-
PXS(e)840x -
VX Instruments GmbH
The PXS840x PXI SMU family is a high-speed, 4-quadrant source measure unit. Carry out measurements directly on the DUT with the integrated CMU and VMU.
-
PX773x -
VX Instruments GmbH
The PX773x is a high precision, high speed source and measurement unit, which is designed for automated high throughput testing.
-
PXS840x -
VX Instruments GmbH
The PXS(e)840x is a high precision, high speed source and measurement unit, which is designed for automated high throughput testing.
-
-
JFW Industries
In circuits are used to lower voltage, dissipate power, and to improve impedance matching. In measuring signals, attenuator pads or adapters are used to lower the amplitude of the signal a known amount to enable measurements, or to protect the measuring device from signal levels that might damage it.
-
DAQ -
ADLINK Technology Inc.
From entry-level to high-end, data acquisition to digital input/output, ADLINK provides a diversity of modular instruments with market-leading price/performance ratio, for bigger and better measurement and automation systems. Now high-speed digitizer, switching, simultaneous data acquisition, high-density multi-function data acquisition, analog output, digital multimeter, and arbitrary waveform generator categories are all available.
-
Supracon AG
In the measurement setup of SQUID electronics (detector variant), the dc SQUID amplifies the small amplitude signals of the detector with a large bandwidth so that they can be further processed with conventional AD converters.
-
UVP-365 -
SAN-EI ELECTRIC CO.,LTD.
This is the standard measurement instrument to measure absolute UV vaiue. All SAN-EI's UV light source fixtures are measured by this meter.
-
UVM-MP -
SAN-EI ELECTRIC CO.,LTD.
Measurement of maximum of 6 points is possible. By use of thee sensor amplifier box, distance between the light receiving inlet and the controller can be extended to 10 meters. Measurement start signals can be independently output by remote control. This is useful for the light source fixtures integrating shutter mechanism.
-
-
TAC1000 -
Rhesca Co., Ltd.
For the measurement of tackiness (instantaneous adhesive strength) of various pastes and adhesive tapes, it is possible to quantitatively evaluate the data, which until now had large errors due to individual differences. First, press the measuring probe, which is controlled (approach speed, pressure force, pressure time, separation speed) against the sample, and measure the adhesive force in the process of separating. Measured data can be processed by a computer. With double temperature control (patented), the sample piece is preheated from the back side with a hot plate and the heated probe penetrates the measurement surface, making it possible to keep the set temperature and the temperature of the test surface to be evaluated constant. Since the pressurization time can be as short as 10msec, it is possible to measure the tackiness caused by momentary contact.
-
PTR1102 -
Rhesca Co., Ltd.
In wire bonding in semiconductor manufacturing, electrodes are joined using gold wires of several tens of microns. In order to measure the pull (tensile) strength and ball shear (shear) strength of this gold wire, this machine has load detection accuracy and fine positioning accuracy. In addition, for the measurement of high load areas such as die shear strength and solder joint strength, this machine supports measurement in high load areas while maintaining accuracy in low load areas by replacing the sensor part.
-
FPR2200 -
Rhesca Co., Ltd.
The friction coefficient is measured by the pin-on-disk method. Also, by measuring the coefficient of dynamic friction, surface destruction occurs due to wear and changes in the coefficient of dynamic friction occur .This machine is the latest model that was created by realizing various measurement modes, improving data resolution, and pursuing ease of use based on the achievements cultivated in the friction and wear tester that we have manufactured and sold in the past.
-
CSR1000 -
Rhesca Co., Ltd.
This tester is highly effective in measuring the adhesion strength (adhesion strength) of hard coatings (Ti, TiN, SiC, DLC, etc.) formed by PVD and CVD on metal surfaces such as cemented carbide. Adopting a scratch test method that allows quantitative measurement with simple operations, the film surface is scratched while increasing the load on the sample surface, detecting film breakage with high sensitivity, and providing the load at which film breakage occurs (critical load). tools and mold tools that require