Showing results: 1456 - 1470 of 8764 items found.
-
Suzhou 3ctest Electronic Co.,Ltd.
Designed to test the induced and conducted disturbance on the telecom lines generated by power line and electrical railway. It meets the requirements of YD/T 993-2006(The technical requirements and test methods of over-voltage and over-current resistibility for telecommunication terminal equipment), ITU-T K21 and ITU-T K44.
-
9355-1 -
Solar Electronics Company
Solar Model 9355-1 Pulse Generator is designed to provide impulse excitation by means of an injection probe placed around interconnecting cables or power wires. The unit uses a charged transmission line (50 ohms) to generate a pulse with less than 2 nanoseconds rise and fall time, and duration of approximately 30 nS, calibrated in a 50 ohm fixture to deliver up to 5 amperes at a rate of 30 p.p.s. for one minute as required by MIL-STD-461D/E, test method CS115.
-
LPSG60662 -
Lisun Electronics Inc.
The start-up test of the special lights pulse start generator is for lighting class industry such as high pressure sodium, it is according to IEC60662: 2011 and GB/T13259-2005 standard requirements.
-
Equip-Test Kft.
Connector assembly check - extreme spring force - used in test modules.
-
YOKOWO Co., Ltd.
New FPC connectors corresponding to the manufacturer’s recommended flexible board thickness of 0.15 mm and 0.2 mm for 0.3 mm pitch and 0.25 mm and 0.3 mm for 0.5 mm pitch are affixed to a proud plate and inserted and disconnected 10 times. The connectors are replaced with new connectors after checking conductivity, and the test is repeated with the number of insertion/disconnection cycles recorded for each pitch and board until conductivity fails.he boards are inserted and disconnected manually, taking care to insert and disconnect horizontally. The boards are inserted with the connector opened and disconnected with the connector closed.(Durability figures are guidelines, not guarantees. Actual performance will depend on connector specifications and conditions of use. Hold connectors close to the pins when inserting and disconnecting.)
-
ADC Corporation
High-speed and high-accuracy measurement of solar cell I-V characteristics in three modes
-
Bird Dog 3 - 11 Channel -
Seismic Source Co.
*Additional Functionality when compared with Standard Bird Dog 3-3*32-bit, high speed, ADC chips for lower noise and increased accuracy*8 Gigabytes of Data Storage, Expandable to 16*GPS based time and location saved for every record*Stable and rugged unit for use in all conditions*Eleven-Channels, unit checks multiple vibrators at once to save time and effort*All test data saved in non-volatile memory for later download and retrieval*Connects to PC via Ethernet or optional Wi-Fi, provides control, data download and real time display and analysis of data and results
-
PGY-QSPI-EX-PD -
Prodigy Technovations Pvt. Ltd.
QSPI Protocol Analyzer (PGY-QSPI-EX-PD) are the Protocol Analyzers with multiple features to capture and debug communication between host and design under test. PGY-QSPI-EX-PD is the leading instrument that enables the design and test engineers to test the respective QSPI designs for its specifications by configuring the PGY-QSPI-EX-PD as Master/Slave, generating QSPI traffic and decoding the QSPI protocol decode packets.
-
UNH IOL
QualiPhyer is a family of software packages used to test a product’s conformance to IEEE 802.3™ and MIPI Alliance electrical and optical standards for Ethernet and MIPI devices. These packages can be used to control oscilloscopes and traffic generators over Ethernet or GPIB connections to test the physical layer characteristics of devices. The software processes waveforms from the scopes to produce results based on algorithms developed at the UNH-IOL.
-
QMan -
Digitaltest GmbH
* Collecting the data from the various test, inspection and monitoring stations * Repairing the boards * Analyzing the faults and linking them to a process or a vendor problem * Confirming the analysis by retesting or re-checking the boards * Adding the analysis to the Quality Database * Utilizing this data in descriptive reports
-
Phoenix Contact GmbH & Co. KG
Phoenix Contact has been developing innovative products for electrical connection and automation technology for over 90 years. To ensure the quality of these products, they are tested on the basis of various directives and standards throughout the entire process of creation. As a result, the products can be integrated in a variety of industries under a wide range of environmental conditions.
-
AIM -
Tinius Olsen
These types of specimen tests are commonly used to determine the key properties of a material, such as tensile strength, Izod and Charpy impact strength, hardness, flammability, shrinkage and gloss/color matching.
-
76562 -
Hickok Inc.
It eliminates the need for back-probing coil wires and disassembly to test at the coil connector or spark plugVariable sensitivity (VS) for greater diagnostic accuracy and expanded application coverageBacked by a Limited Lifetime Warranty
-
Series X57X -
Aries
Quick-Release Universal Zero Insertion Force Dip Test Socket. Aries Universal Test Socket accepts devices on .300 to .600 [7.62 to 15.24] centers. Swing quick-release handle down to open contacts and insert device. Release and handle automatically returns as contacts close onto device leads.
-
CZ23001 -
Aegis Pty. Ltd.
The Aegis QuickSwitch is designed to allow the safe connection of any brand of test set or meter to a telecommunications distribution frame.The QuickSwitch allows switching between monitor, customer and exchange easily.