Showing results: 2491 - 2505 of 8764 items found.
-
ESRP -
Rohde & Schwarz GmbH & Co. KG
The R&S®ESRP EMI test receiver has been designed for diagnostic measurements during development and for precompliance measurements to prepare products for final certification testing. It measures electromagnetic disturbances in the 10 Hz to 7 GHz frequency range, using either conventional stepped frequency scans or FFT based time domain scans to significantly speed up measurements.
-
PC-114 -
Com-Power Corporation
Perform Radiated & Conducted EMI pre-compliance testing at your facility up to 1 GHz. Com-Power PC-114 EMI emissions test system is a ideal solution performing pre-compliance EMC testing from 9 kHz - 1 GHz.. It has essential equipment needed for radiated and conducted EMI emissions measurements. The system includes a spectrum analyzer, antennas, near field probes, a preamplifier, LISN and a non conductive antenna tripod. Pre-compliance testing in EMC is a commonly used term not easy to define. In general, it implies testing done prior to formal testing for legal compliance. Formal legal compliance is performed at a facility designed and equipped with test instrumentation that is fully compliant with the applicable EMC standards. Such facility and instrumentation is capital intensive and can be expensive even to rent and not easily available. Compliance testing is performed per exacting requirements of the Standards and other reference documents adhering to the test methods and last detail. In addition, the test facility may require to be accredited by an accreditation body such as NVLAP, A2LA. Often it is desirable to know prior to compliance testing at such facility, whether a product is close to compliance and also how close. Pre-compliance testing is specially useful for specifications such as FCC, Part 15, EN 55022 or EN 55011 (CISPR 22 or CISPR11). Pre-compliance testing usually means using the full compliance methods but making a few educated compromises in use of site or equipment to reduce costs and testing time. Here are some benefits of pre-compliance testing.
-
ViAcoustics
Small Device Test Chambers are used for >Basic sound level measurement of small products and equipment >Pre-compliance testing of small products and equipment >End of line manufacturing test on small products and equipment Small Device Test Chambers provide acoustic isolation from outside sounds and/or reduce the sounds from the device under test radiating into the host
-
TS9982 -
Rohde & Schwarz GmbH & Co. KG
The R&S®TS9982 is the base system for conducted and radiated EMS measurements. Due to its modular design, it covers a wide range of applications and can be very easily adapted to the measurement task at hand. Any configuration is possible – from conducted measurements and the small precompliance system with a compact test cell to the accredited test system for complete motor vehicles with 200 V/m.
-
EMC-3C -
MVG EMC
This compact 3 meter test range will settle into test areas of limited space while continuing to produce exceptional performance for EMC measurement. Emission quiet zones of up to 1.5m are accommodated with very repeatable results. Suitable for EMC pre-compliance emissions and compliant immunity testing.
-
Explorer Technology Group (ETG)
ETG offers a full range of battery test kits which speed and simplify the process of collecting battery test data . This data can then be downloaded and analyzed with the included Winmeter 5.1 Battery Analysis Software, enabling the user to quickly identify batteries that are likely to require preventative maintenance.
-
Series KD and LD -
Teledyne Defense Electronics Relays & Coax Switch
Your product description goes here.Series KD and LD solid-state relays utilize MIL-PRF-28750 test methods and are packaged in low-profile hermetically sealed cases. They feature fully floating power FET output technology. Options include short-circuit and current overload protection plus a status output line. Switch status returns the true status of the output switch and is optically isolated from the load.MSL 1KD & LD relays are controlled with 15mAdc/3.8Vdc (TTL), and 1mAdc/0.3Vdc (CMOS).Available options include:KD00CK 5Adc, 60Vdc Load KD02CK 5Adc, 60Vdc Load; with switch statusKD20CK 5Adc, 60Vdc Load; with short circuit protectionKD22CK 5Adc, 60Vdc Load; short circuit protection & switch statusLD00CM 10Adc (5Adc without heat sink), 60Vdc LoadLD02CM 10Adc (5Adc without heat sink), 60Vdc Load; with switch statusLD20CM 10Adc (5Adc without heat sink), 60Vdc Load; with short circuit protectionLD22CM 10Adc (5Adc without heat sink), 60Vdc Load; short circuit protection & switch status
-
-
KV Hipot Power Test Equipment Co.,Ltd
Gas instruments detect, monitor or analyze gases present in an environment. Detectors sense situations outside normal operating parameters and are set to alarm when these conditions are violated.
-
KVZG -
KV Hipot Power Test Equipment Co.,Ltd
DC Hipot Tester is applied to measure output voltage and leakage current for zinc oxide arresters, magnetic blowing arresters, power cables, generators, transformers, circuit breakers and other equipment.
-
-
KV Hipot Power Test Equipment Co.,Ltd
oil analysis program is to verify that a lubricated machine is operating according to expectations. When an abnormal condition or parameter is identified through oil analysis, immediate actions can be taken to correct the root cause or to mitigate a developing failure.
-
Instrument Systems Optische Messtechnik GmbH
The latest LumiCam B generation is thus the ideal instrument for easy and reliable measurement of displays and control elements, e.g. in the automotive interior or aviation sector. It is equally suitable for tests in the laboratory and in quality assurance for small batch production.
-
SER -
Saluki Technology Inc.
Saluki SER series EMI receivers comply with CISPR 16-1-1 standard, integrated CISPR-AVG, CISPR-RMS, QPK detectors, and electromagnetic interference measurement. According to CISPR, EN, FCC and MIL standards, which is suitable for EMI testing in home appliances, lighting, automotive electronics, medical, and other industries. Combined with ETR PC measurement software and a wealth of test options, accurate automated testing is possible. The whole system is equipped with a spectrum analysis module and a tracking signal generator to meet the testing needs of users in different fields.
-
4404800 -
BI Communications
The NEW Lancaster Pro-ST is a low-cost wire map tester which tests and certifies structured cabling continuity to a TIA568A/B, USOC and ISDN standards. The new Lancaster Pro-ST displays on screen wiring configurations showing the length of all 4 pairs and length of pair to fault up to 150m (500ft).