Showing results: 6331 - 6345 of 8764 items found.
-
Hilo Test
The products impress with a variety of technical features: TFT display, Ethernet interface, automatic test sequence to a fully electronic generator for even faster and more accurate tests. Our safety testers can be used both stand-alone without a PC as well as integrate with existing systems.
-
-
EasyTest 2.0 -
Acery Technologies
EasyTest © 2.0 is a set of common test automation software platform, with the definition of test engineering, test process editor, test program generation, test execution process, test data on a network share as one of the functions. Using EasyTest © 2.0 can easily set up a large network systems and ground test integrated test system, you can build standalone automatic test system, or automatic control equipment R & D engineers, and other data stored for use in research and development.
-
ACTAS C160 -
KoCoS Messtechnik AG
Stationary test system for carrying out fully automatic final factory tests, type and function tests on all kinds of switchgear devices, such as circuit breakers, disconnectors or earthing switches, regardless of the type of drive unit. All the electrical and mechanical parameters needed for the assessment of switching performance are measured in real time and evaluated without either the main contact chambers or the drive unit having to be opened. The system has analog and incremental input channels for the acquisition of analog quantities.
-
BK9010B -
BaKo Co., Ltd
Based on the BK3010V2 C-Mic Tester, the BK9010B is our fastest C-mic test system. Fully automatic, the BK9010B loads the mics in place and after testing, it sorts passing microphones into 8 quality classes, and failing microphones according to the reason they failed. Each mic is put into its appropriate bin. As testing progresses, you can view the data graphically in real time or save it to be viewed or analyzed later.
-
INDEC -
KoCoS Messtechnik AG
INDEC vacuum test systems monitor a wide range of containers during the production process, including bottles, jars and cans, by measuring the cap panel concavity of their closures which is dependent on the vacuum inside. This non-contact inspection reliably identifies defective containers for automatic rejection.
-
UPA-1 (UPA-3) -
Kharkovenergopribor Ltd.
These portable systems for primary injection testing of circuit breakers which are used in in AC circuits of industrial frequency.
-
Power Test, Inc.
Our equipment tests automatic and automated-manual transmissions. On and off-highway transmission test stands, transmission and hydraulic component test stands and valve body test stands. AIDCO Test Systems offers the latest in modern, electric motor and hydrostatically-driven transmission test stands. All units may include an air-cooled eddy current absorber (standard on the 450E), resulting in minimal dyno test cell noise and reduced maintenance.
-
BK8020 -
BaKo Co., Ltd
The BaKo Type BK8020 ECM Noise Under RF Test System tests microphones under RF noise, using a ‘Direct Injection Test’ in the frequency range of 5MHz~2.5GHz with an amplitude modulated (AM) disturbance signal of 1kHz. You run the system using the controlling PC, which allows automatic configuration and which runs the test sequence automatically. When you finish testing, you can print data as an MS Excel report or save it for comparison and analysis.
-
Axis Aerospace & Technologies Ltd.
AXISCADES is a pioneer in Test Solutions and has a long pedigree in developing Test Systems. AXISCADES has designed and developed Automatic Test Equipment, Test Interface Units/Interface Test Adapters and associated Test Program Set Software for Indian and Global, Aerospace and Defence OEMs and End Users.
-
RFCI61000-4-6 -
Lisun Electronics Inc.
RFCI61000-4-6 RF Conducted Immunity Test System is an automatic test system which is for the conduction sensitivity testing, it is fully meets IEC61000-4-6.2006, ISO11452-4, GB/T17626.6-2008 and GTB152B-CS114 etc standards. RFCI61000-4-6 internal source and broadband power amplifier can be generated 3 voltage test levels: 1v, 3v and 10v, and has the function of the real detect output level. It has two operation software which is calibration software and test software. When measuring, the signal is in 1 KHZ sine wave amplitude modulation system (80%) to simulate the actual harassment, and can through the coupling/decoupling network (CDN or electromagnetic clamp) to make the harassment signal coupled to the device.
-
H21 Series -
Ferrites India
Test pieces in round or square rod forms can be very easily tested for their DC properties. Properties such as coersivity, permeability, magnetization can be tested. The field for testing can be taken to 600A/cm. With our newly designed fixture, if can be taken up to 100A/cm.
-
Ferrites India
Ferrites India offers testing of materials for measurement of their magnetic properties. These materials are in the shape of laminations, stacks, solid toroids, laminated toroids, solid rods or magnets. The testing can be done under wide range of frequency and test specifications and various magnetic properties like B-H Curve, Loss, Permeability, Coersivity, Remnancy, Saturation Magnetization are measured. The testing is done as according with ASTIM/IEC/IS standards.
-
8601 -
Hydraulic Technology, Inc.
The Radiator Flow Test Machine P/N 8601 meets all requirements of military specification MIL-F-45955A (AL). It is completely self contained and requires only connection to a source of shop electrical power to place in operation. A power cable complete with three prong grounding plug is permanently attached to the machine for this purpose. The unit consists of a water storage tank, a pumping system, a flow measuring system, a support and workstation, and the required hose adapters for connection to different size radiators. The complete unit is mounted on swiveling casters. The flow rate is infinitely adjustable from 0 to 120 gallons per minute by means of a panel mounted control valve. The machine is constructed from heavy 10 gauge steel, is double welded and is coated externally and internally with a water-resistant epoxy coating. Flow measurement is accomplished by a digital panel meter with a calibrated accuracy of plus or minus 3 percent of scale between 5 and 120 gallons per minute. Higher flows available on request.
-
Hydraulic Technology, Inc.
Test chambers are available to protect personnel during proof or burst testing. A few samples are pictured below. Chambers are manufactured in polished stainless steel with a clear polycarbonate door(s) for visibility during testing. Fluid port(s) are provided inside the enclosure, while all controls remain outside the enclosure for operator safety. In a hurry? Choose from our selection of Quick Ship Test Systems. basic units can ship within 24 hours or less and chamber systems within 2-3 days. we normally stock test chambers with nominal working area dimensions of either 24" wide x 24" deep x 15" high, 36" x 36" x 15", 48" x 24" x 15" or 72" x 24" x 12" with the door opening from the top. specify individual parameters at our customization page. Need a different size or configuration? No problem, simply specify dimensions and features that more accurately meet your particular requirements and we will be pleased to accommodate you. To customize a system to fit your particular application, please visit our customization page or give us a call at (916) 645-3317.