Showing results: 5461 - 5475 of 8764 items found.
-
6200Z -
Rhesca Co., Ltd.
This device is a test device that evaluates the wetting stress generated between a plate/round bar and molten metal in an inert gas atmosphere by the wetting balance method.It is possible to analyze not only the quality of wetting but also the wetting phenomenon from the obtained wetting curve.
-
Eco Bump -
Teledyne Gas & Flame Detection
Importantly, bump testing is the only way to validate that gas detectors will respond to gas and trigger user alarms.Simplified configuration (no software).Measuring only 7.2” (180mm) in height (including the push button regulator), the pocket-sized EcoBump can easily be stored and transported with minimal shipping costs.With 5.5L of bump gas capacity, EcoBump provides approx. 250 bump tests from a single cylinder making it our most cost effective bump solution.
-
MIG-ITU-K44 -
EMC Partner AG
The MIG-ITU-K44 is designed for power induction testing at line frequencies of 50 and 60Hz. Power induction tests need only be performed at the frequencies of the public power supply or railway power of the country of application. Basic and enhanced level tests can be performed according to ITU-T K44.
-
COMP0804CAP -
EMC Partner AG
Active flammability test system according to IEC 60384-14 Ed4. For testing X & Ycapacitors up to 1uF. The test system includes control of the nominal AC supply via an integrated variac up to 1800V. Impulse amplitudes are programmable up to 8kV which covers all requirements. X1 capacitors are stressed up to 4kV, X2 and Y4 capacitors up to 2.5kV and Y2 capacitors up to 5kV.
-
RMMA -
RightMark Gathering
Before this test packet was created there was no proper software for measuring vital system parameters such as CPU/Chipset/RAM providing steady and reliable (reproducible) test results and allowing for changing test parameters in a wide range. Vital low-level system characteristics include latency and real RAM bandwidth, average/minimal latency of different cache levels and its associativity, real L1-L2 cache bandwidth and TLB levels specs. Besides, these aspects are usually not paid sufficient attention in product technical documentation (CPU or chipset). Such test suite, which combines a good deal of subsets aimed at measuring objective system characteristics, is a must have for estimating crucial objective platform parameters.
-
D3D RM -
RightMark Gathering
D3DRightMark is an independent non-commercial open-source graphics card benchmarking project developed by iXBT.com. It's called to help users estimate graphics cards performance and quality in synthetic tests and real apps, e.g. games. Synthetic tests allow estimating performance and capabilities of separate graphics cards subsystems in order to forecast their behavior in either applications, both existing (that is overall estimation of suitability and prospects for an entire application range) and developing, provided that a given accelerator demonstrates peculiar behavior under such applications.
-
MI 3100 SE EurotestEASI -
Metrel d.d.
MI 3100 SE EurotestEASI is a fast, accurate and easy to use multifunctional measuring instrument which performs a complete set of installation safety tests according to IEC/EN 61557. Besides, the MI 3100 SE EurotestEASI enables on-line voltage monitoring, phase sequence testing and earth resistance measurement. EurotestEASI is equipped with integrated characteristics of fuses and RCDs for PASS / FAIL evaluation of test results.
-
MI 3102 BT EurotestXE -
Metrel d.d.
MI 3102 BT EurotestXE is a multifunctional measuring instrument which performs a complete set of installation safety tests according to IEC/EN 61557. It supports AUTO SEQUENCE® testing of the TN, TT and IT earthing systems. ISFL measurements and the IMD tests can be performed. Besides, the MI 3102 BT EurotestXE enables on-line voltage monitoring, phase sequence testing, earth resistance measurement, illuminance measurement and TRMS current measurement. EurotestXE is equipped with integrated characteristics of fuses and RCDs for PASS / FAIL evaluation of test results.
-
3108 -
Metrel d.d.
MI 3108 EurotestPV is a combined photovoltaic tester and electrical installations safety tester. It enables complete testing of electrical installations according to EN 61557 standards and in addition performs all necessary tests required on single-phase photovoltaic (PV) installations. This includes all of the tests as required by EN 62446, but also includes I - U characteristic, Calculation of STC values as required by EN 61829 and power measurements on Inverter’s DC and AC sides.
-
MI 2016 Multi LAN 350 -
Metrel d.d.
High performance, multifunction test instrument for LAN cabling verification.
-
Metrel d.d.
Photovoltaic electrical installation safety testing is a special area of electrical installation safety testing as it also entails tests and measurements on DC systems, which are relatively uncommon in most domestic, commercial and to a certain extent industrial environments. There is also the addition of photovoltaic-specific tests that are outside the realm of standard test and measurement procedures.
-
MI 3125 BT EurotestCOMBO -
Metrel d.d.
The MI 3125BT EurotestCOMBO performs all the necessary tests for installation safety testing on TT and TN systems. The large graphic display with backlight offers easy reading of results, indications, measurement parameters and messages. Two LED Pass/Fail indicators are placed on both sides of the LCD. MI 3125BT EurotestCOMBO contains integrated characteristics of fuses and RCDs (including B type) for the evaluation of test results.
-
700 Series -
LeakMaster
It’s leak detection simplified. LeakMaster’s 700 series is not only extremely fast, it’s repeatable, and, best of all, it’s user friendly. Add the fact that the 700 series is configurable for pressure decay leak testing, mass flow leak testing, or differential pressure decay leak testing and you can be confident you have one of the most versatile precision air leak test instruments available..
-
LeakMaster
LeakMaster is a leader in the industry when it comes to the manufacturing of calibrated leak standards (calibrated leak orifices). Each leak standard is meticulously manufactured to a specific leak or flow rate at a predetermined pressure. The purpose of each leak standard is to teach, or calibrate a leak test program, and allow the leak test instrument to memorize the characteristics of a leaking part. These leaks are also introduced into production parts to simulate a “leaking or failed” part condition. LeakMaster supplies a calibrated leak standard with every leak test instrument, and provides recertification services for all of their leak standards
-
Traceable Products
Traceable®Battery Tester checks alkaline, carbon, silver-oxide, mercury, nickel-cadmium, and other batteries. Tests battery voltages from 1.35 to 12 volts on 13 ranges. Accuracy is ±5%
