Showing results: 6541 - 6555 of 8764 items found.
-
Wolfgang Warmbier GmbH & Co. KG
The test result is indicated with audible and visual signals. A relay with a dry contact provides the connection to a door opening system
-
-
Metriso B530 -
Wolfgang Warmbier GmbH & Co. KG
Test voltage / Test current: 1 mA < I < 1,3 mAHigh ohmic range: DC 10 volts,100 volts and 500 voltsTest range:low ohmic range: 1 to 10 kOhmhigh ohmic range: 1 kOhm to 199 GOhmOperation: Battery operatedProbes:2x Model 870 (weight: 2,27 kg / ø 63,5 mm) with conductive rubber (grey) and extension,1x hand-held probe Model 45
-
Meltak Technology
Design according to customer's requirementsUse on auto or semi-auto test eqiupments and handler.Pitch range from 0.30mm and above.Pin amount: 2 and above.Key material: Peek,Torlon,PPS,PEI.etcContact with top pogo pin
-
Carl E. Holmes Company
- Active Switching Rectifier, 2 KW, P/N 6016C- Input Range: 9 VAC to 35 VAC, 3 PH- Frequency Range: DC to 10 kHz- DC output: 13.5 VDC, 70 Amps without any heatsink (Test #1)- DC output: 13.5 VDC, 150 Amps with heatsink (Test #2)- Dimensions: 8″W x 8″L x 3″H or similar- AC to DC and DC to DC applications- Generates less heat as power MOSFET Switching is used- The output voltage is the same as the input voltage
-
Aarohi Embedded Systems Pvt. Ltd
Aarohi introduced fully automatic routine testing panel. The primary purpose of the routine test is to insure freedom from electrical and mechanical defects, and to demonstrate by means of key tests the similarity of the motor to a “standard” motor of the same design. this panel also help to enhance productivity, Work efficiency & reduces need for skill operator.
-
-
Model KM 917 -
Kusam Electrical Industries Limited
This is precision instrument adopting HF electromagnetic waves to measure the moisture content ratio without damaging the object under test. It can be set depending on different building material to raise its measurement accuracy.
-
PL-10N -
PINTEK Electronics
*MODEL:PL-10N*IMPEDANCE:1.111MΩ*ACCURACY:±0.5%*FREQUENCY B.W.:DC~50MHz*WORKING POWER:MAX. 1Watt*INPUT VOLTAGE:MAX.250VDC or 200V rms AC*DIMENSION:48mm(L)xΦ16mm(D)*WEIGHT:25g*APPLICATION: Matching the impedance of the Scope probe with the DMM. with this converter, the user can use the oscilloscope to watch the wave from and measure the precise reading from the DMM.
-
4301 Series -
AE Techron, Inc.
The 4301 is designed to work with a standard arbitrary wave form generator or signal source that can be triggered. The system can be ordered with an optional Fluke 281 arbitrary waveform generator, which comes pre-programmed and integrated into the 4301 system. When equipped with the Fluke 281 option, the 4301 provides a complete solution for GR-1089 Section 10/ATIS-0600315.2007 testing.
-
EMC Partner AG
The MIG0603OS2 includes combination wave circuit IEC 61000-4-5. Additionally a 0.5J, 500 Ohm circuit is included in accordance with IEC 60255-5. The two BNC monitor outputs allow monitoring the voltage and current wave shapes by an oscilloscope
-
Cuming-Lehman Chambers
Most antenna measurements need to be carried out in the far field; that is, the test antenna should be illuminated by a plane wave. Typically this is carried out by providing sufficient separation between the source and the AUT so the spherical wave approaches a plane-wave character.Near-Field chambers are an excellent alternative to traditional far-field ranges; testing that can be accomplished on a far-field range can be accomplished on a Near-Field test range. This method of testing allows an operator to employ an indoor anechoic test chamber at a reasonable cost and avoid the problems associated with weather and security concerns often encountered when using an outdoor test range.
-
PH Series -
Ponovo Power Co., Ltd.
PH series travelling waveform fault locating relay/equipment test set is a new device to meet the needs of testing and verification for travelling wave fault location equipment and protection relay with TWFL function.
-
EverythingPCB
We are known worldwide for the M.O.L.E. Temperature Profiler. The Mole is used in the Electronic, Paint, Food, and the Industrial marketplace. The Mole is a stand alone, 6 channel, temperature profiler that it is used in many harsh processes that require the temperature measuring instrument to be inside the heating chamber or "ride along" with the parts or process being measured over time such as Solder Reflow Ovens and Wave SolderMachines.
-
HH2103 -
Colluck Company Limited
Basic Accuracy 1.0%. LCD display 2000 count, 12.8mm figure height. Manual Ranging at your choice (19 Range). Higher Voltage test up to AC 750V and DC 1000V. Higher Current test up to 10A. Resistance test up to 2000KΩ. Diode test. Square Wave Signal Injection