Showing product results. 1 - 15 of 33 products found.
-
M6 - Seismic Source Co.
*Built-in damping and overrange stops*Safe overrange limits*Force up to 2000 G without damage to sensor*Temperature compensated for accurate response over entire temperature range*High slew rate operational amplifiers (1.2 V/usec)*Internal RF shielding on each pin
-
M7 - Seismic Source Co.
*Dual independent Accelerometers for Quality Assurance*Protected against electromagnetic interference (EMI)*Protected against moisture*Input polarity protected*Output short circuit protected*Withstands up to 2000 g's without damage
-
BOOM BOX III - Seismic Source Co.
*Easy to Use, just hold the Arm and Charge toggles, Unit charges and is ready to fire*Web based interface allows easy setup and storage of data on PC, Tablet, or Cell phone*Shooter updated with easy to read graphical display and status LEDs*Same unit used for Encoder and Decoder modes
-
Sigma 4 - Seismic Source Co.
Sigma 4 utilizes the “Seismic Acoustic Monitoring” seismograph node. This is the most advanced, field-proven acquisition system in the world. It works seamlessly to provide the most fully integrated source control/recorder solution.*Autonomous Operation using Internal Storage*USB External Storage for Fast Data Collection*Use internal battery option or external power connection*Internal 3C geophone or external Geophone/Seismometer/Hydrophone/Microphone*Supports standard Ethernet equipment
-
Zero-Time Box - Seismic Source Co.
The Zero-Time Box is designed to compare the start times of source units with the recording system. It is compatible with every source encoder that outputs a start signal on a BNC connector, and also supports every source controller and decoder that does the same. The Zero-Time Box can also be used as a 5 channel precision measurer of timing intervals.
-
VibLink & NavLink - Seismic Source Co.
The VibLink system - Each vibrator, plus the central recorder, is equipped with a VibLink module. The VibLink module uses advanced TDMA techniques to multiplex seven vibrators and the doghouse on one radio channel. And does this all in one second windows. With additional Vibrators, additional seconds are added. The Universal Encoder 3 uses its time slot to send out status updates and request PSS/PFS data. Each Force 3 controller uses its time slot to send out its location, status, and QC Information.
-
Distributed DAQlink4 - Seismic Source Co.
The Distributed DAQlink 4 System is the combination of a standard DAQlink 4 seismograph and internal, high-speed, network extenders. Using inexpensive twisted pair telephone cable, these network extenders will send triggering times and receive seismic data from other DAQlinks. These cable links can send reach 10,000 ft, or three kilometers in length.
-
Seismic Source Co.
Load Cell is designed by Seismic Source Company to measure the Hold Down weight and the output force of the Servo Hydraulic Vibrator unit. The output of the Load Cells can be recorded with any accurate seismic recording system.
-
Bird Dog 3 - 11 Channel - Seismic Source Co.
*Additional Functionality when compared with Standard Bird Dog 3-3*32-bit, high speed, ADC chips for lower noise and increased accuracy*8 Gigabytes of Data Storage, Expandable to 16*GPS based time and location saved for every record*Stable and rugged unit for use in all conditions*Eleven-Channels, unit checks multiple vibrators at once to save time and effort*All test data saved in non-volatile memory for later download and retrieval*Connects to PC via Ethernet or optional Wi-Fi, provides control, data download and real time display and analysis of data and results
-
RTM3 - Seismic Source Co.
The Remote Trigger Module 3, or RTM3 3, is a new generation of impact trigger device. It is designed to time synchronize a single seismic source unit with multiple seismic recorders. It can also be used to synchronize multiple seismic recorders. The RTM3 units use an internal high accuracy oscillator that is synchronized to GPS timing information. Each RTM3 unit requires an external GPS receiver with valid satellite information to synchronize the internal clock. Once the internal clock is synchronized the RTM3 can be used without any GPS signal for up to 10 minutes.
-
-
-
U-Node - Seismic Source Co.
The most successful data acquisition system of our industry was designed by Sercel, France, the 408/428XL Land seismic acquisition system. Over 5,000,000 channels were delivered around the world! The two major building blocks of the field telemetry are the FDU and DSU3. U-Node Alpha connects to either the FDU or the DSU cables and immediately turns the system into a modern "autonomous" nodal system. Wi-Fi or Cable connections can be added to allow "Real Time" display of the seismic signals and records.
-
DAQ3-3 - Seismic Source Co.
The DAQ3-3 is the third generation of portable seismograph systems. The system can be configured as a stand-alone monitoring system, a refraction system or a distributed seismic reflection system. The DAQ3-3 has been designed for temporary or long term installations and can be monitored continuously or periodically, locally or remotely. External clock discipline via GPS Module, VHF/UHF radios or Wire enables usage in any environment.
-
DAQlink 4 - Seismic Source Co.
DAQlink4 is the fourth generation of portable seismograph systems. It can be configured as a stand-alone monitoring system, a refraction system or a distributed seismic reflection system.