Showing results: 6616 - 6630 of 8764 items found.
-
APEX3910 -
AIM GmbH
STANAG3910/EFEX Test and Simulation module for PCIe with 1 dual redundant HS/LS channel and onboardFibre Optic Front End (FOFE). Easily select between EFAbus and EFEX modes for Tranche II Eurofighter. The APEX3910 is a functional replacementfor model APE3910.
-
ACP825-x -
AIM GmbH
ARINC825 (CAN bus) Test & Simulation module for PCI with 2 or 4 electrically isolated CAN bus nodes operating concurrently at CAN bus high speed bit rate of up to 1Mbit/s. The ACP825-x PCI card can work either with full functionality as an active CAN node for testing and simulating or in Listening Only mode for monitoring and recording purposes.
-
ACC825-3U-x -
AIM GmbH
ARINC825 (CAN bus) Test & Simulation module for CPCI with 2 or 4 electrically isolated CAN bus nodes operating concurrently at CAN bus high speed bit rate of up to 1Mbit/s. The ACC825-3U-x CPCI card can work either with full functionality as an active CAN node for testing and simulating or in Listening Only mode for monitoring and recording purposes.
-
Instron
The Instron® Curved Needle Testing System is built on the 5900 system platform and is ideally suited for needles used in abdominal, fistula, vascular, intestinal, or other surgical procedures. This system provides two different needle testing solutions: one for curved needle puncture testing and one for bend testing. The curved needle puncture testing fixture is used to evaluate needle sharpness and insertion force, while the needle bend testing fixture is used to evaluate flexural properties of the needle during use. With its tabletop design, the Curved Needle Testing System has a small footprint and takes up minimal bench-top space. The testing system operates with Instron Bluehill® Universal software that provides test control, data acquisition, test results, and reports, as well as a large library of calculations.
-
Extech LCR203 -
Extech Instruments Corporation
The LCR203 are SMD component tweezers for use with Extech's LCR200 LCR meter. These tweezers make it easy to test and sort simultaneously for single handed operation. Tweezers complete the circuit with components easier than separate test leads. Comes with a 6 month warranty.
-
Extech EX310 -
Extech Instruments Corporation
The EX310 is a compact manual ranging multi meter which features an extra-large 2000 count display and built-in non-contact AC voltage detector (NCV). AC/DC Voltage & Current, Resistance, Diode/Continuity measurements. Includes battery test function (1.5 Volt and 9 Volt). Rubber holster protects the meter. UL listed Cat III – 600 Volt safety rating. Includes test leads, 9 Volt battery and tilt stand.
-
-
Extech PQ1000 -
Extech Instruments Corporation
The Extech PQ1000 is a CAT IV Test Lead accessory kit For PQ3400 series power analyzers. It includes a set of 4, 3 m (10 ft) test leads (black, red, blue, yellow) with shrouded banana plugs on both ends (right angle on one end). Includes test probes, alligator clips, and long reach spring loaded clips.
-
Extech 382254 -
Extech Instruments Corporation
The 382254 is a replacement set of Test Leads for Extech's 382252 Earth Ground Resistance Tester Kit. The test leads are color-coded and durable.
-
Extech 380565 -
Extech Instruments Corporation
The 380565 is a set of Test Leads with Kelvin Clips for the Extech 380580 battery powered milliohm meter. Use these test leads and kelvin clips as extras or spare.
-
Extech 380465 -
Extech Instruments Corporation
The Extech 380465 is a Kelvin Clip Test Lead Set for Milliohm Meter Models 380460 and 380462. The 380465 is built from compact, durable field service housing with a protective cover.
-
Extech UM200-KTL -
Extech Instruments Corporation
The Extech UM200-KTL is a set of 4 wire cables with Kelvin clip connector test leads for the Extech UM200 battery powered milliohm meter. Use them as extras or as a spare if necessary.
-
OTS -
Optik Elektronik Gerätetechnik GmbH
The optics test stations of the OTS series enable the computer-based, software-controlled measurement of optical parameters of individual lenses (including cylindrical lenses) and optical systems. Measured variables are, for example, focal length, MTF, focal length, radius, contact dimension, centering, wedge angle and deflection angle. The optional software module LensTest enables the measurement of the center thickness of lenses and air gaps in complete lenses as well as the measurement of the centering error of individual surfaces.
-
Software For Autocollimators And Test Telescopes -
Optik Elektronik Gerätetechnik GmbH
Small investment - big improvement in measurement accuracy! The CROSSDETECT software is used to retrofit existing autocollimators of all types that are already equipped or can be equipped with a camera. The use of camera and software ensures that the measurement accuracy is increased by a factor of approx. 10 compared to visual measurements! The software can also be supplied complete with an autocollimator.
-
MG Products
Because of the miniaturization of modern electronics , it is important to ensure quality and care with electrical testing. Reliable electrical contact between the test equipment and the testobject (UUT , Unit Under Test) is essential. Specifically for these tests MG Products has developed a series of linear test adapters ( textfixtures ) the MG series. The reliability and accuracy of a contact test adapter is strongly determined by the mechanical construction. Therefore MG Products uses solid aluminum parts.