Showing results: 2986 - 3000 of 8764 items found.
-
J2190A -
PICOTEST Corp.
The J2190A active filter presents a high impedance (approximately 150kOhms) minimizing the loading of the circuit being tested. The output impedance is 50 Ohms allowing low noise coaxial connections to all typical test equipment. The 0.1Hz-10Hz noise band is common for opamp measurements, voltage regulators and voltage references. Many application notes offer schematics of such a filter for test purposes. An engineer’s time is much too valuable to be spent building test equipment. We have created a 4th order high pass and 4th order low pass filter with an optimally flat response and 0dB gain. Additional filters can be cascaded for even sharper cutoff.
-
80609010 -
6TL Engineering
The differential active probe helps to carry weak HF signals far away with the minimum disturbance of the original source. The module accepts discrete wiring or direct spring loaded test probe solder. In any case, the input signal wires might be as short as possible.
-
80609000 -
6TL Engineering
The single ended active probe helps to carry weak HF signals far away with the minimum disturbance of the original source. The module accepts discrete wiring or direct spring loaded test probe solder. In any case, the input signal wires might be as short as possible.
-
80609007 -
6TL Engineering
The single ended active probe helps to carry weak HF signals far away with the minimum disturbance of the original source. The module accepts discrete wiring or direct spring loaded test probe solder. In any case, the input signal wires might be as short as possible.
-
ARA 01 -
York EMC Services Ltd
The Active Receive Antenna (ARA 01) is a compact emissions antenna with an antenna factor comparable to a conventional wideband passive antenna such as the Bilog. The small size makes the ARA 01 particularly suitable for use in anechoic chambers; however it can also be used on an Open Area Test Site (OATS) or at on-site locations.
-
Circuit Check, Inc.
Commonly referred to as In-Circuit Test (ICT), loaded board test can be defined as the task of measuring values of components that have been installed on a printed circuit board (PCB). A second basic category of loaded board test measures simple open and shorts on the board to verify manufacturability standards. Circuit Check supports all forms of in-circuit test strategies with its Performance Grade and Value Line test fixtures.
-
AC-15 -
Tinker & Rasor
Monitors AC on pipelines or structuresAlarm at 15v AC ThresholdConforms to NACE SP0177-2007Audio and Visual AlarmsCalibration Test UnitSuperbright LED'sReplaceable 9v Batteries
-
8020 -
Chroma ATE Inc.
Chroma 8020 has standard test items specially customized and optimized for the features of Adapter and Charger that provides excellent test performance to meet the requirements of mass production. Meanwhile, the software equipped is very friendly and easy to operate that is suitable for production line use.
-
PCI EmbeddedComputer Systems
This adapter connects to the 3U VPX extender to test a PCIe card in a VPX environment. The internal PCB routing is dependent on the VPX profile used in the VPX chassis backplane. Customer must specify the profile used or supply a pin out profile for the slot in question.
-
TR-069 -
QA Cafe
CDRouter TR-069 is an add-on module for CDRouter that provides test coverage for the Broadband Forum's CPE WAN Management Protocol (CWMP). CDRouter TR-069 incorporates a fully functional Auto-Configuration Server (ACS) and is designed to test a wide range of CWMP client implementations including Internet Gateway Devices (IGD) and LAN-side devices such as set-top boxes (STB) and voice over IP (VoIP) endpoints.
-
PA-917010 -
Gardco
The Adhesion Test Analyzer (ATA) takes all of the guess work and subjectivity out of rating the classification of your adhesion results as defined in the ASTM D3359 standard, and is accomplished with one simple instrument.
-
MFA R&D Tunable -
K&L Microwave
Allows passband centered at any frequency over tuning range while adding the capability to vary passband width. Upon input of desired frequency and bandwidth, the filter tunes center frequency and adjusts bandwidth to provide a custom filtering solution on demand. 1dB bandwidth of 5MHz to 20MHz. Suitable for LTE and other test applications.
-
ST332B -
T&M Tools Limited Co
*Multi-functional hand-held VDSL2 test instrument with small size,specially designed for xDSL line test.*It is multi-functional hand-held VDSL2 test instrument with small size,specially designed for xDSL line test
-
Jinan Leading Instruments Co., Ltd.
ADT-01 Primary Adhesive Tester is applicable in primary adhesive tests of pressure sensitive adhesive tapes, adhesive bandage (plaster), label, protective films and other products.
-
SQprobe -
Telchemy Incorporated
SQprobe® is an advanced high speed probe designed for emerging software defined (SDN) and virtualized networks. It monitors IP based voice, video, audio and data streams at Gigabit rates, performing deep packet inspection (DPI) and providing accurate and detailed real time service quality metrics, usage and demographic data.