Showing results: 136 - 150 of 8598 items found.
-
Wilcom Incorporated
Noise and transmission problems are constant battles in the best of worlds. With emerging technologies like IP-video over DSL delivered to the customer over existing copper pairs, it's more vital than ever for telephone companies to test and maintain their outside copper plants.
-
Crystal instruments
EDM Modal Correlation Analysis allows the user to correlate two modal models; EMA and/or FEA models. Comparing the experimental data with that acquired through finite element analysis helps in validating the test results. Users can import the geometry model and mode shape data from FEA or EMA software. A modal mapping procedure is executed to match the EMA and FEA models. After this matching procedure, the new mode shape information from FEA is interpolated and the FEA modal parameters are displayed alongside with EMA results. Finally, to observe the correlation between the results from the two methods, a Cross-MAC matrix is calculated and shown.
-
Data Patterns Pvt. Ltd.
The Second Launch Pad Count Down system is implemented using VXI hardware designed by Data Patterns specific to the application requirements, featuring a redundant system handling upto 14000 I/O points.
-
DPA Components International
DPACI perform counterfeit part analysis on all types of electrical, electronic, and electromechanical (EEE) components. Our suspect counterfeit analysis task groups include source identification, manufacturer validation, external visual inspection, mechanical inspection, electrical test, X-Ray, in-depth internal visual and materials analysis. With one of the largest databases of test reports for EEE components, we can offer similar historical data for correlation with images, test data, certifications and reports.
-
SAE International
The SAE Counterfeit Defect Coverage Tool is a dynamic, web-based application that supplements SAE Standard AS6171 authored by the SAE G-19A Test Laboratory Standards Development Committee. It provides potential test sequences for the identification of counterfeit electrical, electronic, and electromechanical (EEE) parts along a range of risk levels and EEE part types. Allowing users to compare alternative test sequences as a function of resources needed to implement those tests, the SAE CDC Tool is appropriate for those ordering counterfeit detection tests as well as those performing the tests.
-
BP1090 -
BaKo Co., Ltd
*Measure Speaker/Receiver Characteristics*Measure Speaker/Receiver Sound *QualityTest Earphones for Sound Quality and Balance*Measure Rub & Buzz*Test in QA, QC or on the Product Line
-
CDN61000-5C -
Lisun Electronics Inc.
• Application Range: ≤4kV, 1.2/50us pulse, 8 wire unshielded twisted pair (UTP) • Test Voltage: Max 4KV, 2 kV (1.2/50 µs pulse when RJ45 connector is connected. Maximum test voltage is 1.5kV when RJ45 female is unconnected or auxiliary terminal is not protected.) • Coupling mode: 90V gas- discharge tube+250ohm Resistor/Each Wire, 8 Wires Simultaneously-Ground (Common Mode) • Input and output interface: RJ45 connector • Terminal layout (RJ45 connector): First pair of lines: pins 1/2 Second pair of lines: pins3/6 Third pair of lines: pins 4/5 Fourth pair of lines: pins 7/8 • Max. operating speed: 1000MBit/s • Max operating voltage: Max 50V DC • Max operating current: Max 1A Related Instruments
-
VeroSource -
Verocel, Inc.
VeroSource-A verifies that all complex decisions (i.e., decisions with at least two conditions) have taken all possible outcomes; and that every condition within the decision has taken all possible outcomes that have independently affected the decision’s outcome. VeroSource automates the capture and structural coverage analysis of the source code under test.
-
ACS-FC-3U-2 -
AIM GmbH
The ACS-FC-3U-2 is AIM’s high performance CPCIe (PXIe) module offering 2 ports with full function test, simulation, monitoring and analyzer functions for Fibre Channel networks. The ACS-FC-3U-2 is a powerful State-of-the-Art 4-lane CPCIe 2.0 compliant CPCIe board.
-
IIB-1553-CPC -
Western Avionics Ltd.
The IIB-1553-CPCI is an intelligent interface card providing full MIL-STD-1553 test, simulation and bus analysis capability for the CompactPCI bus, with 1553A, 1553B, McAir and STANAG 3838 capability on a single card.
-
SIQMA SC2820 -
SignalCraft Technologies Inc.
The SIQMA SC2820 CPRI Analyzer is the market’s highest-performing, lowest-cost CPRI test instrument. Unlike other solutions, which have been retrofitted to support CPRI, the SIQMA’s high-performance signal processing hardware was designed specifically for CPRI applications. Because of this, the SIQMA SC2820 offers unparalleled performance at half the price of other CPRI analyzers.
-
T-1 -
Tinker & Rasor
3 hole terminal board3 binding postsClear terminal boardSeven colors from stockFits 1.6" OD riser pipeUV stabilized color protectionHigh impact resistanceFire resistant"Easy Grip" top for easy opening with gloves"Anti-Spin" gasket prevents twisting
-
TESTEX Testing Equipment Systems Ltd.
Crease Recovery Tester, to determining recovery properties of fabrics by creasing in a loading device for a predetermined time using a weight suitable for the test method specified (BS/ISO/AATCC), After transferring the specimen to the clamp of the tester, the specimen is allowed to recover and the angle of recovery recorded. Fabric Crease Tester complies with ISO 2313, AATCC 66, BS EN 22313, etc.
-
TF110A -
TESTEX Testing Equipment Systems Ltd.
Crease Recovery Tester & Loading Device, to determine the recovery properties of fabrics by creasing in a loading device for a predetermined time using a weight suitable for the test method specified (BS/ISO/AATCC). After transferring the specimen to the clamp of the tester, the specimen is allowed to recover and the angle of recovery recorded.
-