Showing results: 3541 - 3555 of 8598 items found.
-
Evans Analytical Group®
EAG's Microelectronics Test and Engineering lab network provides semiconductor and electronics design firms worldwide with test, debug, and early engineering support to help you with new product introduction. We actively service a broad range of semiconductor and electronics companies worldwide. Services include ATE testing, Reliability testing and qualification, ESD testing, Failure Analysis, FIB Circuit Edit and Debug. for both ICs and systems
-
MTS1020i -
Applied Test Resources
The MTS-1020i is a cost effective production ATE designed for testing high-volume linear and mixed signal semiconductor devices (Op Amps, high-voltage drivers, DAC, ADC, etc.), both at the wafer sort and final test stages of the manufacturing process
-
UNH IOL
The UNH-IOL has been a contributing member of the MIPI Alliance since 2007 and tests all mobile devices looking for MIPI conformance and physical layer testing including C-PHY, D-PHY, DSI, and CSI-2. All UNH-IOL MIPI Test Fixtures and Tools are available to member and non-member companies. Below are just some of the MIPI Solutions we offer. For a full list please visit our MIPI Test Fixtures page.
-
PXP-100B -
Teledyne LeCroy
The Teledyne LeCroy PXP-100B Test Platform provides a convenient means for testing PCIe 2.0 add-in cards with a self-contained portable and powered passive backplane. The PXP-100B provides power required for both cards under test, and an interposer can be used for connection to a protocol analyzer. As an alternative to an interposer, the PXP-100B includes two mid-bus probe footprints to allow connection to an analyzer via a mid-bus probe.
-
National Technical Systems
Liquid to liquid thermal shock testing applies thermal shocks to test samples by alternately immersing them in a high- and low-temperature liquid medium. Very high thermal ramp rates can be achieved with this method; much more so than air to air thermal shock methods.
-
1662 -
Fluke Corporation
The Fluke 1662 installation tester gives you Fluke reliability and all the basic testing power you need for day-in, day-out installation testing. It tests to all local regulations and is easy and intuitive to use. Additional helpful features like the On/Off switchable auto-start for RCD and loop test, and self-test save time and give you more confidence in your results.
-
CanX -
Schleissheimer Soft- und Hardwareentwicklung GmbH
CanX is the custom testing and simulation software for CAN and LIN bus for specific user groups. The run-time software is designed to execute predefined or automated tasks in testing, work preparation, production, repair or project management.
-
Thermotron Industries
Benchtop Test Chambers provide superior performance over a wide range of applications. Ideal for testing smaller products such as computer components, these chambers combine superior performance with compact design that is perfect for research and development or personal point-of-use testing.
-
Tone Generator -
ComTekk Engineering, LLC.
The new PC-based test software for RF communications engineers and technicians. Flexible, accurate code synthesizer for simulation and testing of 2-way radio systems, repeaters, remote control, ANI, Paging and more.No external hardware required.
-
880 Series -
Teledyne LeCroy quantumdata
The Teledyne LeCroy quantumdata 880 series video test instruments offer a wide variety of solutions for HDMI 1.3, DVI, DisplayPort 1.1 and analog video. There are several options (models) available depending on the digital interfaces and functions that are required for a particular application. The solutions supported by the 880 series include functional testing in the R&D environment, compliance testing, manufacturing testing for production lines and testing in military applications as well.
-
CE-IT -
Tinker & Rasor
The CE-IT gives fast and accurate testing of below ground insulators and road crossing casings. This fully automatic unit tests the insulator without any adjustment by the operator needed.
-
Premier Electrosystems
Premier's composite test panel are multiple testing units housed together in a single panel. All tests are performed sequentially, without any intervention. At the end of the testing cycle, a Ok or faulty signal is given. This is done to fasten the testing process. All test panels are custom made as per requirement. One can choose any of the pre mentioned tests as per their requirement.
-
PCI EmbeddedComputer Systems
Measurement and testing of CompactPCI® assemblies in the 3U Euro-board form factor is greatly facilitated by the use of this test adapter. Easy access to the DUT is guaranteed because the adapter has plug-in connections on 3 sides. The Modern BRIDGE design permits up to 3 CompactPCI® cards and one standard PCI® card to be inserted in one CompactPCI® slot. This allows system developers to implement a large number of tests with little effort and enables you to achieve vital time to market.
-
K1040 -
KINGSINE Electric Automation Co., Ltd.
1. Adopts 6.4 large LCD screen, and provided with VGA video interface, making it available to connect to projector for training;2. With alarm function of housing grounding testing and external voltage input, to guaranty personal security;3. Offer independent Aux. DC to tested devices, 0 ~ 300V/0.6A(Poleless and adjustable);
-
VectorCAST/Ada -
Vector Software Inc.
An integrated software test solution that significantly reduces the time, effort, and cost associated with testing Ada software components necessary for validating safety- and mission-critical embedded systems. VectorCAST/Ada parses your source code and invokes code generators to automatically create the test code (stubs and drivers) required to construct a complete, executable test harness.