Showing results: 2746 - 2760 of 8598 items found.
-
ASM-BF/2 | VP 230044 -
Maschinenbau Haldenwang GmbH & Co. KG.
The ASM-BF/2 4WD roller set is used in test centres and is suitable for vehicles with a single driven axle. It was designed for the exact measurement of the exhaust gas behaviour of vehicles during their transient emission test and permits a driving resistance simulation for the exhaust gas tests ASM-5015 and ASM-2525 (Acceleration Simulation Mode) in accordance with the specifications BAR '97. The ASM-BF/2 4WD is built into the base.
-
YAV90Q04 -
6TL Engineering
The interface YAV90Q04 permits to connect two YAV90096 boards to one 192-Signal contacts Quadrapaddle module. As the Mini-D 50 connectors let 2 free pins (1 and 26), these pins are interconnected to a test point, with the possibility of be grounded. Cable P/N J6200540: Mini-D-50 to Mini-D-50 IDC connectors with 400 mm flat cable.
-
HTC-500 -
Taylor Dynamometer, Inc.
The Hydraulic Test Center (HTC) is a versatile machine designed to test heavy-duty, off-highwayhydraulic components. The 500 hp (373 kW) HTC Complete Bench is for the dealer that services componentsfrom a predominately larger machine size mix such as large mining machines and large excavators. The CompleteBench offers full functionality to test all types of pumps and motors including: transmissions, hydraulic motors,hydraulic cylinders, valve blocks, torque converters, open and closed loop pumps.
-
HTC-500-HFS -
Taylor Dynamometer, Inc.
The Hydraulic Test Center (HTC) is a versatile machine designed to test heavy-duty, off-highwayhydraulic components. The 500 hp (373 kW) HTC Complete Bench is for the dealer that services componentsfrom a predominately larger machine size mix such as large mining machines and large excavators. The Complete Bench offers full functionality to test all types of pumps and motors including: transmissions, hydraulic motors, hydraulic cylinders, valve blocks, torque converters, open and closed loop pumps.
-
-
CM-51S -
Taylor Dynamometer, Inc.
AC power, air and water required at one side wallas applicable.• Room length, and pit location within length,must be determined by user to fit maximumtruck length and rear overhang.• Provide at least one man door for fire escapenear rear of room, but not in rear wall becausesomeone entering during a test could be struckby a stone flung from a tire. Provide ample fireextinguishers at each door and near driver.• “Back-on, Drive-off” installation configurationpreferred.
-
MPK-254 -
MEGABRAS srl
The MPK-254 digital very low resistance ohmmeter is a portable, microprocessor-controlled instrument used to accurately measure resistances of switches and circuit breaker contacts, transformer and motor windings, wire and cable samples, joints in busbars, etc., using test currents from 1 mA up to 5 A.
-
LCR01C -
MINPU TECHNOLOGY CO., LTD.
best handheld LCR Meter*Basic Accuracy: 0.2%*Test Voltage: 1Vrms*Circuit calibration:Open /Short
-
TOB-5V50mA -
Xiamen Tob New Energy Technology Co., Ltd
8 Channels Battery Test Equipment (0.1-50mA, up to 5V) For Lithium Coin Cell Battery Research. TOB-5V50mA Battery Test Equipment is an eight-channel battery analyzer to analyze small coin cells with a range current 0-50mah, voltage 0-5v. Each channel of the analyzer has independent constant-current and constant-voltage source, which can be programmed and controlled by computer software.
-
HH0308C -
Colluck Company Limited
Double Injection Casing. High Accuracy (basic accuracy 0.3%). 6000 count Jumbo LCD display with symbolic signs. Auto Ranging High Voltage test up to 1000V DC and 750V AC. Higher Current test up to 20A AC/DC. Diode and Continuity Check. Measure Resistance up to 60MΩ. Measure Temperature up to 300c. Measure Frequency up to 600k Hz
-
KM-711 -
Kusam Electrical Industries Limited
• VFD-V & VFD-Hz in Dual Display• 5msCREST-MAX capture mode (Peak Hold)• Autoranging Relative -Zero mode• Display Hold• EF-Detection (NCV)• Beep-Jack input warning• Hz Line Level Frequency• Hz Logic Level Frequency• Diode Test• Continuity Test
-
Pacific Instruments, Inc.
Series 6000 digital I/O modules record signals from frequency counters, flow meters, encoders, discrete transducers, IRIG time, etc. which are often part of the test environment. These digital signals are time aligned and recorded alongside the system’s analog measurements. High density digital inputs provide an opportunity to easily include facility controls like switches, valve positions, relays, lights, etc. along with the test data. Series 6000 digital I/O modules also provide outputs generated by user command or automatically by Sequence, Alarms or DSP. User generated outputs are accomplished in software while sequencers can be programmed prior to a test and initiated by program or hardware control. Alarm conditions preprogrammed on the analog side can automatically generate digital outputs which are typically connected to facility control systems or PLCs. A DSP adds powerful real-time processing and is appropriate for PID control loops, derived parameter calculations and a variety of other real-time operations.
-
RMS-0640 -
MegiQ BV
The MegiQ Radiation Measurement System (RMS) is a compact test system that performs 3-axis radiation pattern measurement in non-anechoic spaces.
-
RMS-0660 -
MegiQ BV
The MegiQ Radiation Measurement System (RMS) is a compact test system that performs 3-axis radiation pattern measurement in non-anechoic spaces.
-
3954 -
Technobox, Inc.
The extender/analysis probe permits extension of a PMC card beyong the edge of a host processor front panel, providing access to both Side 1 and Side 2 of a PMC under test.