Showing results: 6271 - 6285 of 8598 items found.
-
-
Model KM 917 -
Kusam Electrical Industries Limited
This is precision instrument adopting HF electromagnetic waves to measure the moisture content ratio without damaging the object under test. It can be set depending on different building material to raise its measurement accuracy.
-
PL-10N -
PINTEK Electronics
*MODEL:PL-10N*IMPEDANCE:1.111MΩ*ACCURACY:±0.5%*FREQUENCY B.W.:DC~50MHz*WORKING POWER:MAX. 1Watt*INPUT VOLTAGE:MAX.250VDC or 200V rms AC*DIMENSION:48mm(L)xΦ16mm(D)*WEIGHT:25g*APPLICATION: Matching the impedance of the Scope probe with the DMM. with this converter, the user can use the oscilloscope to watch the wave from and measure the precise reading from the DMM.
-
4301 Series -
AE Techron, Inc.
The 4301 is designed to work with a standard arbitrary wave form generator or signal source that can be triggered. The system can be ordered with an optional Fluke 281 arbitrary waveform generator, which comes pre-programmed and integrated into the 4301 system. When equipped with the Fluke 281 option, the 4301 provides a complete solution for GR-1089 Section 10/ATIS-0600315.2007 testing.
-
EMC Partner AG
The MIG0603OS2 includes combination wave circuit IEC 61000-4-5. Additionally a 0.5J, 500 Ohm circuit is included in accordance with IEC 60255-5. The two BNC monitor outputs allow monitoring the voltage and current wave shapes by an oscilloscope
-
Cuming-Lehman Chambers
Most antenna measurements need to be carried out in the far field; that is, the test antenna should be illuminated by a plane wave. Typically this is carried out by providing sufficient separation between the source and the AUT so the spherical wave approaches a plane-wave character.Near-Field chambers are an excellent alternative to traditional far-field ranges; testing that can be accomplished on a far-field range can be accomplished on a Near-Field test range. This method of testing allows an operator to employ an indoor anechoic test chamber at a reasonable cost and avoid the problems associated with weather and security concerns often encountered when using an outdoor test range.
-
PH Series -
Ponovo Power Co., Ltd.
PH series travelling waveform fault locating relay/equipment test set is a new device to meet the needs of testing and verification for travelling wave fault location equipment and protection relay with TWFL function.
-
EverythingPCB
We are known worldwide for the M.O.L.E. Temperature Profiler. The Mole is used in the Electronic, Paint, Food, and the Industrial marketplace. The Mole is a stand alone, 6 channel, temperature profiler that it is used in many harsh processes that require the temperature measuring instrument to be inside the heating chamber or "ride along" with the parts or process being measured over time such as Solder Reflow Ovens and Wave SolderMachines.
-
HH2103 -
Colluck Company Limited
Basic Accuracy 1.0%. LCD display 2000 count, 12.8mm figure height. Manual Ranging at your choice (19 Range). Higher Voltage test up to AC 750V and DC 1000V. Higher Current test up to 10A. Resistance test up to 2000KΩ. Diode test. Square Wave Signal Injection
-
AE Techron, Inc.
Easiest-to-use LF wave sequence generator1550+ automotive and aviation standards' tests includedDramatically reduces test time for repetitive test sequencesSemi-automatic calibration routine significantly reduces labor-intensive tasks (like CS101)Very easy to modify included waveform sequences or create new ones
-
DP-1200-18 -
King Design Industrial Co., Ltd.
The precise-type high-acceleration shock tester can provide all half-sine short wave specification specified in JESD22-B110. To meet them, merely change different shock rubber-pad on shock seat. The wave is complete with high repeatability, able to provide user accurate test result.Conform to different test specs such as JESD22-B110 and IEC spec.High repeatability on consecutive shock; acceleration +/- 10%; run time +/- 15%; speed deviation +/- 10%.Table’s four corner-points uniformity P160mm +/- 10%.Can add spring system to reach the requirement of extra high acceleration specification.Using high-efficiency vibration-absorbing seat pad can block out possible floor resonance and protect the factory structure.Easy in operation; no complicate training course required.Module shock rubber-pads are applied per different standards independently. And the rubber-pad lifetime can be prolonged.
-
Yelo Ltd.
Yelo has a wealth of experience in developing and customizing test systems for the Travelling Wave Tube (TWT) market. TWT testers feature specialized power supplies, measurement equipment, and comprehensive control and safety systems.A rugged PLC is used to control all voltages and perform all monitoring functions. User interface and datalogging functions are provided by a supervisory PC that is electrically isolated from the PLC. Power Supplies are solid state with optical fibre barriers to ensure that all control/monitoring is carried out at safe voltages, and with maximum noise immunity. All safety interlocks are hardwired, and the testers are equipped with emergency shutdown features for added security.
-
ToneGenerator -
NCH Software Pty Ltd
Tone Generator is a sine wave generator, frequency generator and signal generator that lets you create audio test tones, sweeps or noise waveforms using your computer or a PDA handheld. Generate sine wave, square wave, triangular waveform, saw tooth waveform, impulse, white noise and pink noise.
-
GDCL -
HV Hipot Electric Co.,Ltd.
The impulse current generator is used to inspect the capacity of electric equipment withstand strong impulse current.It is widely used in lightning arrester and shock wave anti-interference test of electric and electronic equipment under their running conditions and used in other research project.
-
AUTO DIAGNOSTECH LTD
Our innovative multi-function Electrical Component Testers have advanced functions such as voltage power control feed to activate components like radiator fan, headlights, horn, actuators, etc. and the sensor simulator can provide simulation of voltage signals, frequencies, square waves & duty signals with varying intensity to test the feasibility of good sensor signals in comparison to bad ones when troubleshooting vehicle electrical faults.