Showing results: 4216 - 4230 of 8598 items found.
-
TF310 -
TESTEX Testing Equipment Systems Ltd.
45 Degree Flammability Tester, is to determine the fabric flammability (fabric burning test) under controlled conditions, complies with standards like 16 CFR Part 1610, ASTM D1230, ASTM F2100.
-
R&D Interconnect Solutions
Contact Pitch Sizes 0.3mm, 0.4mm, 0.5mm, 0.65mm, 0.8mm, 1.0mm (custom pitches available)•Bandwidth < -1 dB through 65GHz•Current Carrying Capabilities 1 - 4 Amps•Pin Contact DC Resistance 10 - 30 mΩ•Environmental -40°C to +150°C•Self Inductance 0.14nH – 0.36nH•Mutual Inductance 0.12nH – 0.32nH•Typical Contact Force 12 – 35 grams/pin•Contact Compliance 75 µm – 200 µm•Custom Cooling Options Available
-
PCWI International Pty Ltd
Coating thickness gauges are used to test the dry film thickness of most metals, plus concrete, fibreglass, glass, and plastic. The gauges can measure coatings on ferrous substrates, such as steel, and non-ferrous substrates, such as stainless steel and aluminium and non-metals such as concrete, fibreglass, glass, plastic, gyprock and timber.
-
-
-
-
-
CTS -
Magtrol Inc.
Magtrol’s Cogging Test System is a stand-alone test system designed to control and measure Detent Torque, Cogging Torque and Friction Torque. The test System includes a precision geared motor, a TS Series Torque Sensor integrating a 5 000 pulses encoder. CTS 100 to CTS 102 have a built-in security clutches to avoid system overload by mishandling when not in use. The geared motor drives the MUT (Motor Under Test) at a low speed from 1 to 10 rpm (respectively 8 rpm for CTS 103 and CTS 104), while acquiring its cogging torque related to angle position.
-
STG-06-S1 -
ERAVANT
Full band noise figure and gain test extenders are offered to extend noise and gain measuring capabilities up to higher millimeterwave frequency ranges. These extenders are designed to interface with noise and gain test systems that have an input IF of 10 MHz to 1.6 GHz, such as the industry standard Keysight 8970A/B, N8975A and Maury MT 2075B. The noise figure and gain test extenders include a high-performance, solid-state noise source (STZ series) and a full waveguide down converter (STC series), which consists of a Faraday isolator (STF series), full band mixer (SFB series), frequency multiplier, and IF amplifier. A frequency source with an output signal in the frequency range of 10 to 20 GHz is required as a local oscillator for the down converter. The noise source is automatically powered on and off by the noise figure meter.
-
STC-20-10-S1 -
ERAVANT
Full band down-converters are designed to convert high frequency millimeterwave signals down to the baseband at 10 MHz to 1.6 GHz. These down-converters deliver a superior performance since they are assembled with SAGE Millimeter’s instrumentation grade components, such as multipliers, amplifiers, filters, isolators, and more. The below standard offering covers the frequency range of 26.5 to 170 GHz and delivers a typical LO power of 3 dBm and conversion gain of 20 dB. The down-converters provide low harmonic levels and excellent gain flatness, making them ideal for test instrumentation applications. Specifications other than those listed below are available upon request.
-
SWD-5038531040H-15-SB -
ERAVANT
ModelSWD-5038531040H-15-SB is a V band, three-port waveguide directional coupler that delivers a 10 dB nominal coupling level and 30dB minimum directivity across the full waveguide band from 50to 85GHz. The three-port coupler uses a traditional multi-holeand split block design to achieve a flat coupling level, high directivity, and low insertion loss. The interfaces of the coupler are WR-15waveguides with UG-385/Uflanges. Custom coupling levels are available under different model numbers.
-
INGUN Prüfmittelbau GmbH
Manual test adapters (MA) from INGUN are available in several series and series, which differ in terms of use, maximum permitted contact force, parallel stroke, size and service life.
-
ACTAS CF80 -
KoCoS Messtechnik AG
Stationary test system for sequential final factory tests and function tests on up to 8 drives. The drive test system is operated and controlled with the ACTAS operating software. The test position is selected using the multiplex method. The test system can reproduce drive control with the aid of a logic module. This makes it possible to test any drive even if there is no control unit.
-
LS -
inTEST Corporation
Manage the rapidly changing production environment and achieve the lowest cost of test, converting between probe, final, engineering and service positions with ease. Rapid advancements in semiconductor test technology have resulted in highly efficient test cells, capable of device test throughputs far greater than ever before.
-
LSC -
inTEST Corporation
The LSC is a versatile universal manipulator, compatible with probers, vertical plane handlers, and dock-from-below test systems.