Showing product results. 1 - 15 of 161 products found.
-
YAVAP955 - 6TL Engineering
The YAV board AP955 contents 10 CAN Bus programmable bipolar Isolated precision and low noise 0 to 5VDC voltage sources up to 400mA output, with Tripaddle VPC connector.
-
YAV90084 - 6TL Engineering
The YAV90084 can work autonomously as a 10Ch electronic potentiometer of 8 bit resolution. By default, it features 10kOhm resistors), but other resistor values can be assembled under request.
-
YAV90128 - 6TL Engineering
A unique YAV90128 module is able to do all combinations of signal computation at low frequency between the device under test and the various measuring instrumentation inside a test system.
-
AR438 - 6TL Engineering
AR438 module helps with interconnection, power supply and load switching, monophasic and triphasic, adding the current measurement capability up to 10A.Enable input helps for a safe relay disconnection. It is a quick electrical -hardware- disconnection of the relays and is designed to be an auxiliary safety element, so that loads cannot reach the device under test.
-
YAV90057 - 6TL Engineering
The YAV90057 is a High density multiplexer, with 10-bank, 16-channel, 1 pole. It uses high quality electro-mechanical relays allowing each channel to switch current up to 2A and voltage up to 220VDC/250VAC.
-
YAV91CLR - 6TL Engineering
The YAV90CLR card allows the intensity and color test of LEDs, in an automatic, precise and cost-effective way. The card has a calibrated RGB light source as a tool for calibration of the 16 channels or for detecting dirt on the optical heads.
-
YAV90086 - 6TL Engineering
16 power relays SPST Switching up to 2770VA 16A Switching 125Vac 10A Switching 277Vac CAN Control (or Ethernet with Ethernet to CAN Gateway) Drivers dll & VIs available
-
YAVAL964 - 6TL Engineering
- 16 channels DPDT or SPDT 2A- CAN bus control and 24Vdc (J1 and J2 connectors to chain multiple cards).- Access to relay-pins through wire-wrap or terminal block- Address selection DIP switch on top layer- LED monitoring- Drivers dll & VIs available
-
YAVP20T1-1-1 - 6TL Engineering
The format of the AL568 optical fiber for LED test is the most convenient and effective system on the market. It sists in the space of a 90 Series VPC module and only requires connection to a USB port to get data from up to 18 LEDs.
-
H71006000 - 6TL Engineering
precision servo pusher H7100 6000 is the recommended solution for PCB test systems combining Functional, In-Circuit, and Hipot Test in one fixture.It is available as a 19″ Rack atonomous module, including all drive, control and safety components for easy integration in automatic test systems using standard Mass Interconnection Receivers.Includes a servo motor with numerical control driving a precision gearbox, and two robust linear guides for pusher frame travel.
-
YAVP20T1 - 6TL Engineering
20 x Multiturn potentiometers Passive board Custom Values
-
YAV90097 - 6TL Engineering
32-Lines selectable High-Open-Low connection 3kV 1,0A Relays (Cool connection) Hipot test capabilities CAN Control (or Ethernet with Ethernet to CAN Gateway) Drivers dll & VIs available
-
YAV90304 - 6TL Engineering
8 x 24Vdc PNP Inputs 16 x 24Vdc 600mA PNP Outputs CAN Control (or Ethernet with Ethernet to CAN Gateway) Drivers dll & VIs available
-
YAV90077 - 6TL Engineering
21 channels 1 thread 6A 250V 2 Fault Insertion Buses Switching up to 250W CAN Control (or Ethernet with Ethernet to CAN Gateway) Drivers dll & VIs available
-
YAV90HVT - 6TL Engineering
32 relays High Voltage (Up to 1500V) Multimeter/Amperimeter 14 bits resolution. 1x Analog Output and 2x Digital Outputs Internal automatic calibration CAN Control (or Ethernet with Ethernet to CAN Gateway) Drivers dll & VIs available Automatic module identifier