Com-Power Corporation
Com-Power Corporation has been a supplier of instrumentation for EMI / EMC Testing (electromagnetic compatibility), telecommunication ( Part68 ) and product safety ( UL / IEC CSA) testing since 1989.
- (949) 459-9600
- (949) 635-0329
- sales@com-power.com
- 1679 Placentia Avenue
Costa Mesa, California 92627
United States of America
-
Product
Spectrum Analyzer
-
Spectrum Analyzer from Com-Power of have a frequency range of 9 kHz up to 3.2 GHz. With their light weight, small size, and friendly user interface, the SPA-900TG offer a bright easy to read display, powerful and reliable automatic measurements, and plenty of powerful features. Applications include broadcast monitoring/evaluation, site surveying, EMI precompliance, research and development, education, production, and maintenance.
-
Product
Antennas
-
Com-Power EMI / EMC broadband and tuned antennas cover the frequency range of 9 kHz - 40 GHz. Most electronic products are required meet the various international EMC regulatory standards before they are introduced to the market. Com-Power provides a wide range of EMI antennas and accessories. We also have the capabilities to assist you with custom EMC antennas for special applications to meet your exact needs.Contact us today to learn more about our EMC broadband test antennas.
-
Product
Feed Through Capacitor
-
Feed-through capacitors with a value of 10 μF are made so that they can be used in RFI/EMI test setups like MIL-STD-461A/462A. Now, many other standards, such as RTCA DO-160G, require them to be used. In this particular application, the capacitor offers a low RF impedance across the power supply. So, a current probe can be used to accurately measure the electromagnetic interference (EMI) currents made by the device being tested.
-
Product
LISNs - Single Phase
-
Com-Power single-phase LISNs cover 9 kHz to 400 MHz in five series — 1x, 2x, 3x, 4x, and 5x — with current ratings from 20 A to 100 A for CISPR 16, ANSI C63.4, MIL-STD 461, DO-160, and CISPR 25 conducted emissions testing.
-
Product
Transient Limiters
-
Transient limiter LIT-153A and LIT-930A protects a spectrum analyzer input from high-level transients from the line impedance stabilization networks during EMC conducted emissions testing. It has a combined frequency range of 9 kHz to 30 MHz. The built in high pass filter helps reduce 50/60 Hz line feed through. (see application notes)
-
Product
LISNs - Three Phase
-
Com-Power three-phase LISNs in three series — LI-3P-1X (CISPR/ANSI, 150 kHz–30 MHz), LI-3P-2X (CISPR/ANSI V-AMN, 9 kHz–30 MHz), and LI-3P-4X (MIL-STD-461, 10 kHz–10 MHz) — covering 16 A to 100 A per phase for conducted emissions testing of industrial, commercial, and military three-phase equipment in Delta and Wye configurations.
-
-
Product
Antenna Mast
Automated and Manual
-
Automated and Manually Operated Antenna Masts. The Com-Power AM series antenna masts are motorized and designed for EMI testing. Antenna mast Model AM-400 allows antenna height variation from 1 to 4 meters, and Model AM-600 can vary antenna height from 1 to 6 meters. They are constructed using non conductive fiber glass material. The antenna is mounted on a one piece cross boom, which is attached to a slider assembly. The slider assembly rides over the length of the mast on delrin wheels. It is pulled by a rope and pulley mechanism powered by a electric motor. The slider assembly is equipped with a spring loaded braking mechanism to prevent inadvertent descent should the rope fail.
-
Product
EM Clamps
-
The EM Clamp or a Bulk Current Injection Probe (BCIP)can be used for IEC/EN 61000-4-6 tests on ports/cables for which no Coupling/Decoupling Network (CDN) is available.
-
Product
Turntables
-
Used for EMC testing motorized turntables TT-400X and TT-600X are used in commercial electromagnetic compatibility testing as low-profile, above-ground platforms for spinning the equipment being tested (EUT). The turntable can hold and rotate equipment that is on a desk or on the ground. The device is turned so that the position or angle at which the EUT gives off the most electromagnetic interference can be found. By using the switch on the remote, you can turn the turntable in either direction. The motor and the gear reduction drive that goes with it make up the rotation drive. These turntables are made from non-conductive weather proof materials. You can buy any kind of ramp you want to use to move heavy equipment onto the turntable.
-
Product
Antenna Kits
-
Com-Power offers five portable antenna kits suitable for offsite EMC testing. These kits are supplied with a custom hard plastic carrying case which has individual compartments for all the included items.
-
Product
Current Probe Calibration Fixtures
-
Calibration fixtures are used for calibration of Coupling Loss/Transfer Impedance of current probes and BCI probes, as well as for the calibration of test levels for conducted immunity/susceptibility tests using BCI probes.
-
Product
Bulk Current Injection Probes
-
The Com-Power CLCI-100 and CLCI-400 are precision bulk current injection probes designed for conducted immunity testing. The CLCI-100 covers 10 kHz to 100 MHz, while the CLCI-400 extends up to 400 MHz and complies with MIL-STD-461 and RTCA DO-160. Both models feature split-core ferrites for easy cable insertion and are compatible with calibration fixtures for accurate RF injection and monitoring.
-
Product
System Controllers
-
System Controllers feature multi-device control, variable speed control, fiber optic interface with antenna mast and turn table, full control via front panel or PC software, on-site antenna calibration, 19" 3U rack-mountable, and a 3-year warranty.
-
Product
Magnetic Field Generator
-
The Com-Power APF-5060 magnetic field generator is specifically geared towards generating magnetic fields for immunity testing. The APF-5060 with its corresponding loop antennas provide a standalone solution for magnetic field immunity testing as per IEC/EN 61000-4-8 and all the derived product standards.
