Showing results: 3811 - 3825 of 6590 items found.
-
MFG-8203 -
MCH Instruments Co.,Ltd.
Features:*Low distortion, high stability*Linear and logarithmic sweep function*Sweep time and width adjustable*External voltage control frequency (VCF)*Internal& external modulation AM/FM with modulation control*Output signal compatible with TTL/CMOS*Seven types of waveforms such as sine, square, triangle and ramp*DC power output attenuation can be applied to main output signal*Built-in frequency meter:0.1Hz-30Mhz
-
CPCI395 -
AcQ Inducom
The CPCI395 features 16 analog voltage outputs, integrated on the CompactPCI standard. Each output has a 12- or 16-bit resolution and a software programmable output range (0..+10V or -10..+10V). Control of the analog output is as easy as writing the binary equivalent to a dedicated register (per channel). Conversion takes place automatically. If desired, channels can be synchronized by presetting the channels and then give a simultaneous update command.
-
PA72G14180 -
APPLICOS
The PA72G14180 is a 14-bit arbitrary waveform generator, capable of generating waveforms at speeds up to 180Msps. An onboard offset voltage source allows generating offset signals while maintaining optimal utilization of the DAC’s digital range. With the 64MWord of memory, there is lots of room for uploading long complex waveforms. Also uploading of many different patterns is possible, allowing switching patterns with minimal bus communication.
-
HSL-DO32-M-N/HSL-DO32-M-P -
ADLINK Technology Inc.
Slave ID consumption: 2 consecutive from odd"N" type for NPN sinking type outputSwitch capacity: Single channel 500 mA; all channels 60 mA at 24VDCPhoto couple isolation voltage: 2500 VrmsResponse time: ON→OFF: 180µs, OFF→ON :1.2µsLED indicator: Power, Link and Output statusPower supply: +10V to +30 VDCOperating temperature: 0 to 60°C
-
TMD Technologies Ltd
Fully integrated microwave tubeHigh voltage switched mode power supplyBuilt in test electronics (BITE)Designed for the harshest environments – strong, sturdy, robust, MIL SpecHigh reliability – all products fully ESS tested before shipmentHigh level of customer support worldwideHigh level of product innovation – TMD won a Queen’s Award for innovation in 2005 for a low noise radar power supply design
-
LC Series -
Battery Metric
The LC Series machines are low current, low power devices configured for management of low capacity batteries. These devices offer very high input resistance and have current control as low a 0.25 micro Ampere. These machines also offer 3 current ranges. Select the device that has the current ranges required for the intended application. Other voltage and current configurations are also available.
-
Analog Devices Inc.
Analog Devices provides a portfolio of quad resistor networks with excellent matching specifications over the entire temperature range. All of our resistors can be accessed and biased independently, making them a convenient and versatile choice for any application that can benefit from matched resistors. Our resistor networks provide the precise ratiometric stability required in highly accurate difference amplifiers, voltage references, and bridge circuits.
-
WFG-110 -
Wuntronic GmbH
The Model WFG-120 System is a complete 3 axis fluxgate magnetometer packaged in a rectangular/parallelpiped package of dimensions 0.75\" x 0.75\" x 2.75\". The package corners are rounded to enable the unit to fit inside a 1.0\" diameter cylinder. The system operates from one of two optional input voltages: regulated ±5 VDC or unregulated ±7 to ±12VDC and consumes a total power of 200 mW.
-
WFG-120 -
Wuntronic GmbH
The Model WFG-120 System is a complete 3 axis fluxgate magnetometer packaged in a rectangular/parallelpiped package of dimensions 0.75\" x 0.75\" x 2.75\". The package corners are rounded to enable the unit to fit inside a 1.0\" diameter cylinder. The system operates from one of two optional input voltages: regulated ±5 VDC or unregulated ±7 to ±12VDC and consumes a total power of 200 mW.
-
40-967-160-F -
Pickering Interfaces Ltd.
This termination option is capable of accepting heavy duty connection wires and uses rising clamp screw terminals to minimize the danger of copper strand damage. Users should care take to protect the termination and provide a suitable method of restraining the cables. Pickering cable assemblies for this product are contained elsewhere in this data sheet. Interfacing PCB?s should be designed with suitable clearances for the voltage the application requires.
-
40-967-160-M -
Pickering Interfaces Ltd.
This termination option is capable of accepting heavy duty connection wires and uses rising clamp screw terminals to minimize the danger of copper strand damage. Users should care take to protect the termination and provide a suitable method of restraining the cables. Pickering cable assemblies for this product are contained elsewhere in this data sheet. Interfacing PCB?s should be designed with suitable clearances for the voltage the application requires.
-
Elcometer Limited
Wet Sponge Technique: A low voltage is applied to a moist sponge. When the sponge moves over a coating flaw, liquid penetrates to the substrate and completes an electrical circuit, setting off the alarm. The wet sponge technique is suitable for measuring insulating coatings less than 500μm (20mils) on conductive substrates, and is ideal for powder coatings and other coatings where the user does not wish to damage the coating.
-
ZET 7154 -
ZETLAB Company
Digital inclinometer ZET 7154 is used in static systems for platforms positioning control (2-axial mode) with a tolerance below 0,1 %. Low power voltage and CAN protocol enable integration of ZET 7154 digital inclinometer into almost any industrial system. “Set to zero” option allows to calibrate the sensor to zero in every axis, thus preventing platform critical tilt in the set coordinate.
-
MT1000 And MT2000 Series -
Maury Microwave Corporation
The MT1000 and MT2000 mixed-signal active load pull systems are the best commercially proven solutions capable of performing load pull at high speeds of up to 1000 impedance/power states per minute with no limitation on Smith Chart coverage, under the following conditions:Single-tone CW and pulsed-CW RF signalDC and pulsed-DC biasTime-domain NVNA voltage and current waveforms and load linesFrequencies between 1 MHz and 40 GH
-
ZET 7054 -
ZETLAB Company
ZET 7054 digital inclinometer is used in static systems to sustain platform position (biaxial mode). Low supply voltage, MODBUS protocol application – all this enables embedding of ZET 7054 inclinometer in almost any industrial system. The “Set zero position” function allows to set transducer to zero on each of the axes, and thus, to prevent the platform critical inclination along the coordinate specified.