Showing results: 1291 - 1305 of 6590 items found.
-
Pickering Interfaces Ltd.
These standard voltage and high voltage 50 Pin D-type connectors are used for both PXI & LXI switching and simulation products for medium density applications.
-
Pickering Interfaces Ltd.
These standard voltage and high voltage 9 Pin D-type connectors are used for both PXI & LXI switching and simulation products for low density applications.
-
Pickering Interfaces Ltd.
These standard voltage and high voltage 37 Pin D-type connectors are used for both PXI & LXI switching and simulation products for medium density applications.
-
72-7660 -
Tenma
Compact, regulated constant voltage power supply for service field, hobby and telecommunication equipment. It provides three different voltage output for different usage.
-
GBR-250 -
RARA Electronics Corporation
GBR-250 series high voltage resistors are made in a thick film technology on ceramic substrates (Al2O3 96%). These elements are used in high voltage applications.
-
Dr. Hubert GmbH
The main features of our power amplifiers are extreme broadband, low distortion and stability, above all. All amplifiers are operated and parameterized via a comfortable application software. The basic devices are mere voltage suppliers and provide 2 supply voltages and a USB interface.The letter "E" in the model name represents additional features: the amplifiers can optionally be operated as voltage amplifier or current amplifier; there are monitor outputs for voltage and current, and there are 3 symmetrical supply voltages available for optional selection.The amplifiers from the QE range provide "auto-commutating" voltage supply. In contrast to the E-models, 3 bipolar supply voltages are individually switched either automatically or manually.The QE-models provide highest sink outputs and are thus also suitable for operation as active load.For detailed information on HUBERT amplifier technology please see our White Paper No.1: HUBERT power amplifiers.
-
Production Triangular Voltage Sweep (TVS) Option -
Materials Development Corporation
In traditional TVS measurements, the operator must select the end points of the mobile ion peak todetermine the area to analyze. Though the selection of these points is a simple matter for the operator, the required input precludes using this technique in asemi-autonomous production environment. The goal of TVS Production testing is the rapid determination of mobile charge concentration with little or no operator input. The test methodology must be compatible with production environments where accuracy, easeof use, and minimum operator involvement are of paramount concern. Also, the possibility of automated wafer handling must be considered.
-
76600 -
Hickok Inc.
High visibility, simple to use, one handed dynamic voltage testing. Indicates Power and Grounds. Test the circuit's ability to deliver current and identify loose, corroded or broken wires. Capture intermittent spikes or drops in voltage. Take Voltage Snapshots in any mode, any time.
-
6521 -
Peaceful Thriving Enterprise Co Ltd
The multi-function automobile tester has LCD display to indicate the measured result. It has polarity detection with the LEDs for a positive and negative indication of DC voltage. For auto use, the functions included the measurement of DC voltage and current, signal frequency and max/min voltage, resistance and power providing testing.
-
6210A IN (Ranges: 0.5kV, 1kV, 2.5kV, 5kV) -
Standard Electric Works Co., Ltd
● Microprocessor-controlled.● Four insulation test voltages.● Insulation resistance; auto ranging on all ranges.● Bargraph indicates test voltage; rise and decay can be observed during tests.● Visual and audible warning if external voltage is present.● Fully protected: crow bar.● Carry case.● EEPROM calibration.
-
6211A IN (Ranges: 1kV, 2.5kV, 5kV, 10kV) -
Standard Electric Works Co., Ltd
● Microprocessor-controlled.● Four insulation test voltages.● Insulation resistance; auto ranging on all ranges.● Bargraph indicates test voltage; rise and decay can be observed during tests.● Visual and audible warning if external voltage is present.● Fully protected: crow bar.● Carry case.● EEPROM calibration.
-
YAV90096 -
6TL Engineering
Selectable voltage and current, comparation and measurement Drive sink or source up to 32 mA per channel Maximum voltage in output selectable from 9 to 24 VDC Possibility to use I7Os in parallel Pin voltage comparator with logic readout at fix +4VDC 10-bit resolution pin voltage measurement with CAN bus value readout Build-in editable test steps sequence (test script) Size: form G
-
WMA-IB-LN -
Falco Systems
The WMA-IB-LN can be used to double the output voltage of two high voltage amplifiers by driving them in bridge mode, or as high impedance input buffer while maintaining precision and ultra-low noise. The WMA-IB-LN model has been designed specifically for the Falco Systems WMA-200 high voltage amplifier. Two WMA-200 amplifiers combined with one WMA-IB-LN provide unprecedented noise performance and output voltage range.
-
SG3005 -
Shanghai Jiuzhi Electric Co., Ltd.
The instrument can measure DC positive and negative value of DC voltage, ripple voltage, ripple factor. It can measure AC sine wave (power frequency) and the AC of non-sinusoidal wave voltage peak (positive peak value, negative peak value, peak-peak value), peak value/ √ 2 (true RMS), RMS value of waveform deviation factor and higher harmonics. And can display and save the voltage waveform, pressure raising curve.
-
US, A, AD Series -
UDEYRAJ ELECTRICALS PRIVATE LIMITED
Confirms to IS 6792, IEC 156 • Tests insulating oils to IS, IEC, ASTM, etc.• Test voltage to 100kV• Motorized rise of test voltage: 2kV/sec • One piece construction with safety interlocked transparent hood covering test cell• Test voltage can be held at any desired level• kV meter continues to indicate breakdown voltage even after breakdown• Light weight: 36 kg only• Portable, rugged and with cover.