Showing results: 1456 - 1470 of 2629 items found.
-
MPK-2000e -
MEGABRAS srl
The MPK-2000e digital very low resistance ohmmeter is a portable, microprocessor controlled instrument used to accurately measure resistances of switches and circuit breaker contacts, transformer and motor windings, wire and cable samples, joints in busbars, etc., using test currents from 1mA up to 10A. It uses the Kelvin-type, four-terminals measurement principle, thus eliminating errors caused by lead and contact resistances.
-
Curtiss-Wright Defense Solutions
The 3U VPX (VITA 46 and 48.2) Flash Storage Module (FSM) provides high-performance, high-capacity, solid-state SATA storage with AES-256 bit encryption using an Application Specific Integrated Circuit (ASIC) that is FIPS-140-2 validated (Certification #1472). The 1" pitch conduction-cooled solid state storage device utilizes high reliability SLC NAND flash designed for the most demanding application.
-
Augury Inc.
The Auguscope incorporates over 3 years of Electronics and Analog circuit development, resulting in best in class analog signal sampling at never before seen sampling rates. The Auguscope can record both Vibration and Ultrasonic (AE) sensors and can be used for mechanical diagnostics, as well as leak detection, pump cavitation and steam traps. The result is a small, portable device, that replaces over $40,000 worth of monitoring equipment.
-
Anatek Instruments
This is the fully-assembled, cablibrated and tested Blue ESR/Low Ohms Meter The latest and best Bob Parker design and successor to the famous Dick Smith ESR/Low Ohms Meter. This handy and affordable meter measures capacitor equivalent series resistance (ESR) in the circuit. ESR is a very important characteristic of capacitors greater than 1 ufd. This meter makes measurements which are often impossible to check with capacitance meters.
-
CMM-11 -
Sonel S.A.
The CMM-11 multimeter is designed for quick diagnostics of devices and electric circuits. Thanks to an ergonomic design and pocket size, CMM-11 will find a place in every tool bag and will not take much space. It has all basics measuring functions, and thanks to the rubberized housing is not endangered by falls from up to 2.5 meters and mechanical damages. It's the perfect solution for every electrician, fitters, installers and maintenance services.
-
FA Instruments
FA Instruments Parametric Analyzer offers all the functions of a 'big box' circuit testing solution, without the 'big box' footprint!The Parametric Analyzer is an advanced software module that can performs within the Crystalvision suite. The module provides all the functionality and testing schemes you would expect from a high-end solution, with all functionality being geared towards providing the maximum information to the FA engineer.
-
Analog Devices Inc.
Analog Devices provides a portfolio of quad resistor networks with excellent matching specifications over the entire temperature range. All of our resistors can be accessed and biased independently, making them a convenient and versatile choice for any application that can benefit from matched resistors. Our resistor networks provide the precise ratiometric stability required in highly accurate difference amplifiers, voltage references, and bridge circuits.
-
Elcometer Limited
Wet Sponge Technique: A low voltage is applied to a moist sponge. When the sponge moves over a coating flaw, liquid penetrates to the substrate and completes an electrical circuit, setting off the alarm. The wet sponge technique is suitable for measuring insulating coatings less than 500μm (20mils) on conductive substrates, and is ideal for powder coatings and other coatings where the user does not wish to damage the coating.
-
DP10 -
Validyne Engineering
The DP10 Pressure Sensor, is designed for low and medium pressure measurements, to laboratory accuracy, of corrosive liquids and gases. In typical AC excited bridge circuits, this transducer delivers a full scale output of 30 mV per volt at 3kHz. The unit operates with carrier system including the Validyne CD15 since wave carrier demodulator and CD16 miniature DC input DC output carrier demodulator.
-
Test-X Fixture Products
Test-X VOC Series overclamps are used for testing bare or loaded printed circuit boards with open vias and to minimize board flex.The VOC Series overclamp comes with adjustable delrin pressure fingers, anti-rotating hex nuts, hinge and latching assemblies, mounting instructions and hardware.The VOC Series will accomodate fixtures with dress frames or newer style fixtures using full-size top plates.
-
PP319FTC -
Matco Tools
Full functioning voltmeter measures in 1/10th of a volt increments from 1/10th of 1V up to 70V. Easy to read dual polarity indicators: red (+) symbol indicates positive green (-) symbol indicates negative. Circuit breaker protects the vehicles electrical system and your Power Probe. 20' extension lead gives you 40' total of lead. Great for RV'S, trucks and trailers.
-
28017 -
Parallax Inc.
The MEMSIC 2125 is a low cost, dual-axis thermal accelerometer capable of measuring tilt, acceleration, rotation, and vibration with a range of ±3 g. For integration into existing applications, the MEMSIC 2125 is electrically compatible with other popular accelerometers. MEMSIC provides the 2125 in a surface-mount format. Parallax mounts the circuit on a small PCB, providing all I/O connections so it can easily be inserted on a breadboard or through-hole prototype area.
-
40-592A-113 -
Pickering Interfaces Ltd.
The 40-592A FIBO (Fault Insertion Break-Out) Matrix Module is a large-scale high density switching matrix based on the Pickering BRIC format. The fault insertion BRICs are designed for applications requiring the simulation of a variety of faults in complex, high pin count, applications involving sensors and control units. Typical faults that can be simulated are open-circuits, short circuits to ground or battery, or short-circuits between input/output lines.
-
40-592A-104 -
Pickering Interfaces Ltd.
The 40-592A FIBO (Fault Insertion Break-Out) Matrix Module is a large-scale high density switching matrix based on the Pickering BRIC format. The fault insertion BRICs are designed for applications requiring the simulation of a variety of faults in complex, high pin count, applications involving sensors and control units. Typical faults that can be simulated are open-circuits, short circuits to ground or battery, or short-circuits between input/output lines.
-
40-592A-107 -
Pickering Interfaces Ltd.
The 40-592A FIBO (Fault Insertion Break-Out) Matrix Module is a large-scale high density switching matrix based on the Pickering BRIC format. The fault insertion BRICs are designed for applications requiring the simulation of a variety of faults in complex, high pin count, applications involving sensors and control units. Typical faults that can be simulated are open-circuits, short circuits to ground or battery, or short-circuits between input/output lines.