Showing results: 616 - 630 of 2629 items found.
-
Circuit Check, Inc.
Commonly referred to as In-Circuit Test (ICT), loaded board test can be defined as the task of measuring values of components that have been installed on a printed circuit board (PCB). A second basic category of loaded board test measures simple open and shorts on the board to verify manufacturability standards. Circuit Check supports all forms of in-circuit test strategies with its Performance Grade and Value Line test fixtures.
-
EM-6873 | 20 Hz – 100 KHz -
Electro-Metrics Corp.
The EM-6873 Loop Sensor Antenna uses passive circuits to transform magnetic field components between 20 Hz – 100 kHz to an equivalent open circuit two-terminal voltage on the receiving instrument. Use of the conversion Factor Chart, supplied with each antenna, will yield the strength of the magnetic induction field referenced to a uniform field. The loop is electrostatically shielded and therefore is sensitive only to the magnetic component (B-field) of the electromagnetic fields.
-
Circuit Assembly Corp.
High quality connectors are just the beginning. Circuit Assembly (CA) also has over three decades of experience in producing a wide variety of cable assemblies for various applications. CA has the technical and manufacturing capabilities to provide customers with high-quality and cost-effective cable assemblies tailored to meet their needs. Circuit Assembly utilizes a quality process recognized by ISO 9001, and CA's cable assemblies are UL/CSA certified.
-
Naprotek, LLC.
The SemiGen SBL 2000 series Beam Lead PIN Diodes feature fast switching speeds at both low capacitance and resistance. Beam Lead PIN Diodes have high levels of mechanical strength and stability during assembly. These diodes are suitable for microstrip or stripline circuits as well as circuits requiring high isolation from a series of mounted diodes such as multi-throw switches, phase shifters, attenuators and modulators.
-
Osborne Transformer Corp.
Osborne’s Isolation Transformers are used to step-up, step-down and isolate voltages in single phase circuits. Isolation may be used to provide output circuit immunity from voltage spikes and noise (both common-mode and transverse-mode) present on the input system. The isolation can allow separate grounds on both the input and output sides of the transformer. Osborne also designs with a range of electrostatic shielding to provide several levels of noise immunity.
-
Pro-Check 725 -
LITE-CHECK LLC.
Pro-Check trailer light testers with advanced electrical diagnostics are rugged, lightweight, and economical. They independently test each electrical circuit on a trailer to ensure proper connectivity. The Pro-Check identifies each specific type of electrical wiring fault. Lite-Check’s patented active diagnostic system takes the guesswork out of identifying trailer light and electrical problems. The Pro-Check commercial trailer light tester with electrical circuit diagnostics, not only identifies faults, but the specific circuit the fault is on. Faults are identified as “Open Circuit”, “Open Ground”, “Short” (w/all circuits identified), or “Chassis Ground”. Audible alarms alert technicians to found electrical faults.
-
Vitek L36 -
ViTec Co. Ltd
Compact module of linear pulsed illumination, consisting of 12 high-speed non-lensing LEDs and a control circuit that limits the maximum duration and minimum duty cycle.
-
VECTOR Electronics and Technology, Inc.
Board for IBM AT/ISA, IBM PC-XT and PCI expansion card size and edge contacts on tabs. Available with different circuit patterns for prototyping applications.
-
Renesas Electronics Corp.
Renesas' communications product portfolio includes a synchronizing pulse width modulating (PWM) current mode controller for subscriber line interface circuits (SLICs).
-
1040C/CU -
Arbiter Systems, Inc.
Calibrate panel meters, transducers, circuit breakers and relay units with Model 1040C, a portable, field-ready unit featuring eight key calibration functions.
-
VECTOR Electronics and Technology, Inc.
Card edge board for STD and S-100 bus specification card size and edge contacts on tabs. Available with different circuit patterns for prototyping applications.
-
7611 -
Peaceful Thriving Enterprise Co Ltd
The device use microelectronic technology to monitor the variation of current, which helps technician to protect the automobile circuit from current overloading during the maintenance.
-
3702 -
Peaceful Thriving Enterprise Co Ltd
Check on 6, 24 and 48V DC systems. DC voltage mesurement and used as an extension cord for testing electrical circuits in cars , trailer, boats.
-
1924 -
Peaceful Thriving Enterprise Co Ltd
*Check on 12V systems. *Quickly check continuity of dead circuit, sockets, door bells, motors, switches, fuses and other high voltage appliances.
-
SG-L09 -
Jinge Testing Machine Co.,Ltd
This machine is used for testing the adhesive strength of copper-foil circuit on the PC board or tin-foil, aluminum-foil, tap,…etc, which are adhered to rhe suface of object.