Showing results: 1906 - 1920 of 2629 items found.
-
UFTS-CM_20Ch/ 20Ch -
Misum Systech Co., Ltd.
All of the lithium batteries need protection circuit module to prevent any loss of battery function capacity and explosion during over charge , over current or short to cause increased temperatures. This equipment is used to test and inspect a battery's voltage, current, charge, discharge PCM status, IR, and others.
-
Z-Axis Europe
FTFs are test fixtures which are dedicated for testing flex-based components and assemblies such as displays, touch panels and more. A weak spot in a typical functional test system is the method to connect DUT flexible cable to a circuit board where the simple method of attaching the flex directly with an ZIF or LIF connector fails.
-
1180 IN -
Standard Electric Works Co., Ltd
● High quality Taut Band movement.● Battery operated.● Solid state circuitry.● Battery check feature.● Automatic circuit discharge.● Three insulation test voltages(DC) : 250V, 500V, 1000V● Continuity test : 50 Ω● AC voltage measurement : 500V● Color-coded scale.● Fuse protected.
-
DMOM-600 -
Manta Test Systems
The DMOM-600 is specifically designed for testing EHV circuit-breaker contact resistances, bushing contact joints, welding joints, or for any low-resistance measuring application. This high current and very lightweight (33 lbs/ 15 Kg) micro-ohmmeter is designed to meet the IEEE C57.09-1999 (5.15) requirement for testing circuit breaker contact resistance.
-
E-Labs, Inc.
This type of testing is required for devices, systems, and applications within the military and aerospace industries. Weapons, aircraft, ground and support equipment, electrical, and electronic systems must meet the established requirements.During electromagnetic interference the component's electrical circuit is affected due to either electromagnetic conduction or electromagnetic radiation from an external source.
-
ST-1520 -
MRC ltd.
Capable of measuring earth voltage.2mA measuring current permits the testing of earth resistance without tripping earth leakage current circuit breakers in the circuit.Auto power off function.The timer operates automatically for approximately three to five minutes when the "push button switch" and "timer on button" are pressed together.
-
Kuhne electronic GmbH
An oscillator is an electronic circuit designed to produce either audio or radio frequency signals. These will generally have sineusoidal wave form, but other wave shapes such as square and sawtooth are possible. In radio equipment oscillators will always have a low output power, and if a radio frequency is produced, the oscillator is acually a basic radio transmitter.
-
Circuit Check, Inc.
Circuit Check matches top side test targets to your specification and needs. The Signature Series pneumatic drive fixture is the industry standard for precision, accuracy and repeatability.Today’s fifth generation Pneumatic drive supports as many as 8,000 test probes with centerline spacing to 25mil, and contacting test pads as small as 0.014″.
-
Q1 Test, Inc.
In-circuit-testing (ICT) is usually used on mature products, especially in subcontract manufacturing. It uses a bed-of-nails test fixture to connect with multiple test points on the PCB’s bottom side. With sufficient access points, ICT can transmit test signals into and out of PCBs at high speed to apply evaluation of components and circuits.
-
LBW -
Simplex Inc
The LBW-Series Load Banks are completely self-contained, freestanding units which include all resistive load elements, load control devices, load element branch circuit fuse protection, main load bus and terminals, water cooled system, control power supply, unit controller and malfunction detection system.
-
Premier Electrosystems
Premier Electrosystems deals in a wide range of voltage and current sensing devices. A Current/ Voltage sensor is a device that detects electric current/ voltage in a circuit and generates proportional signal. The generated signal can be then used to display the measured current in an ammeter, or can be stored for further analysis in a data acquisition system, or can be used for the purpose of control.
-
Vidac Solutions
This system is a modern replacement for an obsolete product tester. This tester Hipots the lamp under test, checks for proper operation at the required voltage and also detects short circuit operation and the 5KV ignitor pulse signal. This tester allows for quick calibration to permit traceable/repeatable results and store the test results for product tracking.
-
LM Series -
Koyo Electronics Industries co., ltd
Models in LM-2100 series equipped with LCR meter are designed to measure inductance and dissipation factor of the coil to which DC current is superimposed. Special circuit is built in to protect the LCR meter from surge voltage. Applied current can be step by step in the remote mode. Voltage application is impossible with the safety cover open.
-
H261 -
Howell Instruments, Inc.
The H261 Series Temperature Indicator Tester provides accurate testing of the calibration and operation of temperature indicators. This is achieved by simulating thermocouples, resistance temperature devices, and other millivolt transducers. These testers also troubleshoot thermocouples and millivolt sources by measuring their outputs. In addition, they measure thermocouple circuit resistance and harness insulation resistance.
-
Model 8515-D -
Magnetic Instrumentation Inc.
The Model 8515-D is a medium-energy, high voltage, and capacitor discharge type ringing demagnetizer capable of desaturating Ceramic and Rare Earth magnetic materials. The Model 8515-D is easily adapted to a wide range of production and laboratory demagnetizing requirements. A modern solid-state electronic control circuit, coupled with a rugged, heavy-duty discharge SCR and fixture, make this demagnetizer a highly reliable, low maintenance unit. The electronic voltage control circuit prevents the Model 8515-D from being discharged before the preset energy level has been reached, avoiding incomplete magnet desaturation. An easy to read front panel meter monitors the capacitor voltage. The energy storage level can be easily changed in the field. Integral electrical interlock and fail-safe circuitry provide a high degree of operator safety.