Showing results: 2116 - 2130 of 2629 items found.
-
FS2352B -
FuturePlus Systems
The FS2352B is a logic analyzer probe used to test DDR3 DIMM memory. When used with the triggering and analysis capabilities of Keysight’s Logic Analyzer modules, it gives the user an effective tool for debugging, testing and verifying DDR3 DIMMs. This logic analyzer probe has a CKE qualification circuit that allows for the use of older Keysight logic analysis modules when testing systems using power saving modes.
-
TT9103 -
Matco Tools
*Portable and water resistant trailer light tester and trailer brakes tester that allows the user to perform all testing functions without the use of the vehicle*Tests 7-spade, 6-round and 4/5-flat pin type trailer harnesses*Short circuit protection*Turn signal simulation and power verification LED*Water resistant*Trickle charger and trailer plug adapter includedInternal battery compartment (battery not included)
-
Amprobe Test Tools
Check out the full line of quality Amprobe accessories, which are field tested to help you get the most out of your Amprobe tools, including:*Rugged test leads of all types and sizes for Amprobe instruments*Current transducers for maximum accuracy and safety*Temperature accessories for surface, air/gas, or liquid temperature measurements*AC relays for low-voltage control circuits*Adapters, software, carrying cases and more
-
MPI Advanced Semiconductor Test
Every MPI manual probe systems can be configured with a variety of different holders for printed circuit boards (PCB’s) in order to provide in addition to on-wafer, versatile, convenient, and accurate Signal Integrity (SI) measurements with single-ended or differential RF probes. Measuring signals at the end of the channel for eye-patterns, deterministic jitter, distortion, TDR (Time Domain Reflectometry) impedance, cross-talk, coupling, and losses, or even S-parameters is easily accomplished.
-
5047 -
Abaco Systems Inc
The 5047 provides breakout of all ECM signals for debug, design validation and development. Plated through holes on the PCB allow soldering of probe wires to IO, Data, Power and Serial Identification signals. LEDs indicate presence of 3V, 5V, +12V, -12V and Ground. Elevates the ECM module by 2 mm and saves wear on the ECM carrier board connectors. Since this is a debug too there is no serial identification circuit.
-
PDS-A Series Hybrid -
Texio Technology Corp.
As compared with dropper-method DC power supplies, the unique switching and dropper circuit systems bring low output noise at same level, light weight less than half, and compact body. PDS-A power supply corresponds to EU RoHS regulation in consideration of environment. GP-IB, RS-232C, USB and LAN optional control boards are available and users are able to download API and drivers software from TEXIO web-site.
-
CD16 -
Validyne Engineering
The CD16 Miniature Carrier Demodulator is designed to deliver a 0 to 5 Vdc output from a variable reluctance transducer and operate from unregulated 9 to 55 Vdc power. A square wave excitation of 5 kHz is furnished to the transducer and the solid state integrated circuit amplifier and demodulator converts the transducer signal to an analog dc output. Zero and Span adjustments are made through access holes in the case.
-
GT4000 -
Guide Technology, Inc.
A true breakthrough in high-speed, asynchronous and serial interface test technology the GuideTech GT4000 leverages the power of CTIA continuous time-stamping technology to eliminate the need for supplemental triggers, pattern markers or clock recovery circuits. GuideTech CTIAs enable serial interface pattern verification and full jitter analysis in milliseconds for fast, automated characterization or high-throughput production test on any ATE platform, including low-cost and in-house testers.
-
900-398 -
Phase II Plus
The 900-398 Vickers Hardness Tester is engineered to produce a clear indentation and a more precise measurement. By means of a load cell, closed circuit system for control, the CPU controls testing force to load/dwell/unload, allowing for the highest degree of accuracy. The large LCD shows the measuring methods, the testing force, the indentation length, hardness value, the dwell time of the testing force as well as the number of the measurement on its screen.
-
SUG335 -
Lisun Electronics Inc.
The SUG335 is a 1.2/50μs Transient Over-voltages Tester. The polarity interval time can be at least 1s. The standard voltage waveform complies with the IEC 60335, IEC61180, IEC 62052-11: 2003, IEC 61008-1: 1996, IEC 61009-1:1996 and IEC 60947-1: 1995, IEC60060, IEC1036 surge voltage test and has been used for safety testing to determine if the clearance was fulfilled the safety requirement while the transient voltage in the circuit.
-
78065 -
Hickok Inc.
Current diagnostic routines dicatate time consuming circuit testing and NEVER test the component.More and more of today's vehicles are using Pulse Width Modulated (PWM) motors, actuators and solenoids. You can't simply test them by directly applying 12 volts. This can cause expensive misdiagnosis. PWM Power Pro is the only tester that can adjust the output percentage from 0% 100% to effectively pinpoint the cause of the failure.
-
Meco Instruments Pvt. Ltd.,
High AccuracyRange Selection & Single Person Push Button OperationLCD Back Light Function with Indicator SwitchData Holding Function, Function Icons on DisplayMeasurement of AC Voltage upto 600VACMeasurement of Phase Sequence between (Phase-PhaseVoltage)with LED Indicator Auto Range (Insulation Test)LED Indicator for High VoltageInbuilt Protection Circuit to prevent the harm of reverse voltagesBattery Operated with AC Adaptor3 Ranges of Voltage & Insulation Resistance
-
SYSTEM 8 (AICT) -
ABI Electronics Ltd
The SYSTEM 8 Analogue IC Tester is the answer to testing analogue devices. The key feature of the AICT is its ability to functionally test all common analogue ICs and discrete devices in circuit. It is also capable of testing all types of analogue and digital components by means of the well-known, power off V-I test technique. For users requiring only the latter function, please select the Analogue Test Station section.
-
LKZ-720 -
Sonel S.A.
*Detection of wires and cables (live or not)**detection of cables in ceilings, walls and floors,**detection of breaks in cables,**tracing cables in building installation,**locating power points and switches in buildings,**locating short circuits between leads,**tracing shielded cables,**tracing cables in metal ducts.*Identification of fuses on the distribution board.*Tracing underground cables.*Tracing conductive water and heating pipelines.*Non-contact detection of live cables.
-
AudioJog Rack 8 -
CableJoG Ltd
There are 2 rows of 9 LED's corresponding to each of the possible connector pins and one for the screen (or ground) connection. As each pin is activated, the LED's indicate all connections associated with that pin, so that short, open and crossed circuits can be easily found. The LED's also show the possibility of high resistance or leakage connections. 2 LED's indicate a good digital network connection, either Straight through, or Crossed over.
