Filter Results By:

Products

Applications

Manufacturers

Showing results: 1636 - 1650 of 2637 items found.

  • Single Rear Slot Universal Low-Profile PCI to Compact Flash Adapter

    P312 - TEAM SOLUTIONS, INC.

    To cater for the latest generation of Low Profile PCs that can only use Low Profile PCI add-in boards, Elan has created the P312. This model, from the P-Series range, features a Compact Flash Type II ejector and a circuit board that conforms to the MD1 profile specification. It will allow you to use any Compact Flash card such as IBM MicroDrives, Bluetooth cards, WLAN 802.11b cards, data acquisition cards, pager cards, GPS cards etc.

  • Tone Coax Cable Generator

    240 HAL - Aines Manufacturing Corp.

    The AINES 240 HAL Tone Generator is a water resistant tone generator equipped with a weathertite 2 conductor modular cord and jack. The set can be connected to the Network Interface Device (NID) with either the two individual clips or the modular cord. This allows the CPE circuit to be viewed in both directions, towards the Central Office and towards the customer premise. In the event the CPE does not have a jack, but instead has a cord, plug the cord into the Model 240s jack and transmit tone!

  • Vacuum Meters

    MRC ltd.

    * Absolute vacuum & absolutepressure measurement.* Wide measure range from 1 to1500 mbar.* Overload protection up to 2000mbar max.* 8 kind display units :torr, mm Hg, micron, mbar, KPa,Pa, inch Hg, psi* Separate probe, easy operation.* Heavy duty sensor used for air, oilgas, liquid.* Auto shut off saves battery life.* Microprocessor circuit.* Maximum & minimum records.* Data Hold function.

  • Thermalyze Extension for Steady State Analysis

    Lock-In - OptoTherm, Inc.

    Steady-state thermography is limited to detecting hot spots that heat up a minimum of 100 mK (0.100°C). This may be useful for locating shorts on high-power devices, but is inadequate for detecting low power defects such as semiconductor device leakage current or short circuit with very low or very high resistance. Steady-state thermography also suffers from poor spatial resolution as the heat from localized hot spots diffuses rapidly, blurring the location of the heat source.

  • Solid-State Relay with Power FET Switch to Protect Against Overload and Short-Circuit Currents

    Part No. SR75-2 - Teledyne Defense Electronics Relays & Coax Switch

    The SR75-2 solid-state relay utilizes a power FET switch that is protected against overload and short-circuit currents. The short-​circuit protection feature not only provides protection should a short or overload occur while the relay is on, but will provide protection should the relay be switched into a short. It comes in through-hole or surface-mount 16-pin DIP packages.MSL 6Available options include:SR75-2 0.5Adc, 400Vdc Load; 3.8-32Vdc Control; through-hole mountSR75-2S 0.5Adc, 400Vdc Load; 3.8-32Vdc Control; surface mount

  • Oil Test Set

    NEO TELE-TRONIX PVT. LTD

    We are the most reliable manufacturer and exporter of Oil Test Set that is ideal for testing of Breakdown / Withstand Test of Transformer and Circuit Breaker Oil. This test set is manufactured using premium quality raw material under the supervision of versed professionals. Moreover, the offered test set is checked by our quality inspectors on various parameters to ensure its flawlessness at clients' end. Our valuable clients can avail this Oil Test Set from us at competitive prices.

  • Materials, Structure, Surface, and failure analysis Services

    Materials Analysis Technology Inc.

    MA-tek provides wide span of materials analysis, structure analysis, surface analysis, and failure analysis. By technology segment, MA-tek provides 9 major service lines:1. Electrical Failure Analysis (EFA). 2. Physical Failure Analysis (PFA). 3. Structure Analysis. 4. Surface Analysis. 5. FIB Circuit Editing6. Reliability Testing. 7. Reverse Engineering of Benchmark Analysis. 8. IP Consultancy. 9. Quality Management Training Course.

  • Ruggedized Power Amplifier

    AMP3095 - Exodus Advanced Communications

    AMP3095 is our 31 to 40 GHz, 5 W Min broadband module, featuring a Class AB linear GaAsFET hybrid design. It operates from a 9 VDC supply at 16 A with gain flatness of 8.0 dB Max peak to peak. With instantaneous wide bandwidth, built-in protection circuits and high reliability the AMP3095 is suitable for all single channel modulation standards and applications such as EMI/RFI, EW, communications, SATCOM and general testing for MM wave products.

  • Plug Socet & Cord Testing

    Educated Design & Development, Inc.

    Flexing Tests: On flexible cables (or cords sets with fitted plugs), electric tools or hand lamps. Meets requirements of standards such as IEC 60335, IEC 60227, IEC 60745 and UL745. This product is for continuous bending tests of cables or cord sets fitted with plugs. The model F39 allows the simultaneous testing of two samples in it's standard version. This not only allows for substantial time savings, but also allows for the testing current circuits to be simplified by looping through the cables.

  • Varactor Tuning Diodes

    Macom Technology Solutions Holdings Inc.

    MACOM’s GaAs and Silicon varactor tuning diodes provide broadband performance ranging from 10 MHz to 70 GHz. They are ideal for high Q filter and VCO electronic tuning circuits and are available in die form, flip chip, plastic and ceramic packaging. These GaAs diodes boast a constant gamma series for higher frequency and high Q applications and silicon abrupt and hyper abrupt series in plastic packaging are suitable for high volume surface mount applications.

  • High-Standard Bench-Top Laser Source

    Shanghai Stone Communication tech Co., Ltd

    These bench-top laser source has built-in high-feature Semi-conductor laser device, it is the SM output, with less than 10MHz plus width. Based on the advanced micro-processor control system, this instrument integrated high precision ATC and ACC(APC) to control the electric circuit, in order to realize the high stable output of the laser device, and make the operation easily and directly. We also can provide user required communication port with the software to realize remote control from the PC.

  • Circulators

    Teledyne Lincoln Microwave

    The most common application of a circulator is as a duplexer, allowing the transmitter and receiver in a radio or radar unit to share a common antenna. Energy is transferred from the RF Source to the antenna during transmit, and from the antenna to the receiver during the receive cycle. In each case the circulator functions to isolate the inactive port from the propagated signal. Most importantly, the transmitter output is not passed to the receiver input, preventing the high transmitter power from damaging the sensitive receiver input circuits.

  • Switch Mainframe

    SW1001 - HIOKI E.E. Corp

    Switch between voltmeter and battery tester while testing. 66 channels max. (2-wire) to 18 channels max. (4-terminal pair). Circuit design friendly for impedance measurements that minimize errors between channels (Effect: 0.01% f.s.*). For BT4560 100 mΩ range, R measurements, and a measurement frequency of 1 kHz. For OCV measurement, internal resistance measurement, and external potential measurement of battery cells. Measure battery modules up to 60 V DC.

  • Copper PCB

    Amitron Corp.

    The Amitron process is capable of producing 20 plus ounces of finished copper and reliably spray coat a protective and consistent solder mask with imaged nomenclature. Amitron utilizes a unique process referred to as "Laminated Deposition". This combination of processes allows extreme copper thickness requirements to become very practical and cost effective. The process utilizes heavy base copper that when placed in our plating and etching systems will deliver consistent and reliable high power circuits.

  • Dip Coating Systems

    Specialty Coating Systems

    SCS Dip Coating systems, which are available in free-standing floor or tabletop models, are specifically designed for production applications that do not require large in-line systems. SCS dip coating systems can be used to apply a range of coatings, as well as photo-resists and solder masks, that are part of printed circuit board applications all with a level of precision that manufacturer's demand. Both SCS models include a host of features that make them an ideal choice for lab and production operations.

Get Help