Filter Results By:

Products

Applications

Manufacturers

Showing results: 1936 - 1950 of 2637 items found.

  • Tone & Probe Kits

    Triplett Test Equipment & Tools

    ProTone Wire Locator Kit features a powerful tone generator and a filtered, ultra-bright lighted probe. The CTX590 functions as a high quality wire locating tool that uses an inductive probe to sense a tone placed on the wires by its associated tone generator. The tone generator provides RJ11, RJ45 and insulated alligator clip connections. The Red/Green LED on the probe indicates continuity, voltage, and polarity. The probe also includes an ultra bright LED tip, fluorescent light noise filter and sensitivity control. The CTX590 can be used for tracking down short circuits, telephone central office connections, and other wire locating applications. Includes (2) 9V batteries and case.

  • Programmable Multi Output DC Power Supply

    LQ6324P - Aplab Limited

    - Multi Output Linear DC Power Supply- Digitally Controlled Output Settings- Store / Load 10 Sets of Output Settings in Internal Memory- USB Interface Provided- Programmable Arbitrary Variable Output by Feeding Coefficient of the Curve- User Friendly Front End- Low Cost General Purpose Laboratory Bench Unit- Fully Protected against Overload and Short Circuit- 5V/5A with Over Voltage Crowbar Protection for Digital ICs- Three Independent Outputs Electrically isolated from Each Other- Electrically Floating Outputs up to 500V DC w.r.t. Ground- Precise Regulation, Low Ripple and Noise for Both Constant Voltage & Current Operation

  • Programmable DC Power Source

    ODP3032 - KILTER ELECTRONIC CO.,LTD

    3.9 inch high resolution ( 480 x 320 pixels) TFT large LCD display,can clear visual display state and a plurality of relevant parametersTwo separate controllable output 0V ~ 30V / 3A,A fixed output 5V / 3A, total output of high power 195WThree channel output and electrical isolation,greatly reduce circuit interference Low ripple and noise of pure power:(<300 uVrms / 2 mVpp)Output resolution :1mV/1mAInternal implementation independent, parallel, series , positive-negative four kinds of work modes and automatic trackingOvercurrent and overvoltage protection function,Can easily set up the overvoltage and overcurrent protection parameters,effectively protect the load

  • Crossing Control Bypass Switch

    XCBS-DL - Green Switch Innovations

    The XCBS-DL is permanently wired into each crossing warning system, and can be configured with either a removable or non-removable bypass key. Simply connect the track connection harness to the designated track connection terminals. To prevent unnecessary operation of the crossing warning system, insert the key and select "bypass", rotate the knife switch to "bypass" and the crossing is disabled. When in the "bypass" position, a Dummy Track Load is connected to the track wire connections in parallel with the rails and the crossing approaches are shorted, preventing unnecessary activation when track equipment is working in the crossing approach circuit. The opening of one track lead may be desired to prevent unnecessary activation with intermittent shunting on the crossing approaches close to the crossing.

  • Crossing Control Bypass Switch

    XCBS - Green Switch Innovations

    The XCBS is permanently wired into each crossing warning system, and can be configured with either a removable or non-removable bypass key. Simply connect the crossing control circuits to the designated terminals on the XCBS. The rotating "knife switch" on the left side of the XCBS allows the crossing warning system to be controlled for manual test purposes. To prevent unnecessary operation of the crossing warning system, insert the key and select "bypass", rotate the knife switch to "bypass" and the crossing is disabled. The non-removable bypass key adds an additional level of security for the Bypass function. Optional hookup can be made to the auxiallary terminals to include the activation of a strobe or event recorder input when the XCBS is placed in the "bypass" position.

  • PXI 32 x SPDT Reed Relay

    40-110-121 - Pickering Interfaces Ltd.

    Our 40-110 and 40-115 range of reed relay switching modules are available in both Changeover (SPDT) and Normally Open (SPST & DPST) configurations. Connections are made via a front panel 96 pin male micro-D connector. For applications requiring improved bandwidth and crosstalk performance please look at our 40-120/125 range of shielded reed relay cards. General purpose reed relays are suitable for the construction of small switching networks, for slaving up to larger switches or for operating external devices (e.g. lamps, solenoids etc.). To simplify inter-relay wiring, interconnection points are built onto the circuit board thus easing the construction of complicated wiring.

  • 6.8 GHz Wideband Synthesizer with Integrated VCO

    ADF4356 - Analog Devices Inc.

    The ADF4356 allows implementation of fractional-N or integer-N phase-locked loop (PLL) frequency synthesizers when used with an external loop filter and an external reference frequency. A series of frequency dividers at another frequency output permits operation from 53.125 MHz to 6800 MHz. The ADF4356 has an integrated VCO with a fundamental output frequency ranging from 3400 MHz to 6800 MHz. In addition, the VCO frequency is connected to divide by 1, 2, 4, 8, 16, 32, or 64 circuits that allow the user to generate RF output frequencies as low as 53.125 MHz. For applications that require isolation, the RF output stage can be muted. The mute function is both pin- and software-controllable.

  • Active Filter

    J2190A - PICOTEST Corp.

    The J2190A active filter presents a high impedance (approximately 150kOhms) minimizing the loading of the circuit being tested. The output impedance is 50 Ohms allowing low noise coaxial connections to all typical test equipment. The 0.1Hz-10Hz noise band is common for opamp measurements, voltage regulators and voltage references. Many application notes offer schematics of such a filter for test purposes. An engineer’s time is much too valuable to be spent building test equipment. We have created a 4th order high pass and 4th order low pass filter with an optimally flat response and 0dB gain. Additional filters can be cascaded for even sharper cutoff.

  • Inductive Motor Control

    ams AG

    The inductive motor control position sensor family detects the electrical position within one pole-pair of a rotating shaft and can be used for the motor commutation of a brush-less DC (BLDC) motor. Based on the inductive sensor technology, this family measures the coupling between an excitation coil (TX) and two receiver coils (RX) via a rotating target. The coils are executed as printed circuit coils and the rotating target is a simple punched metal part. With the correct layout of the coils and the target, both synchronized to the number of pole-pair count of the motor, the IC output is proportional to the electrical angular position within one pole-pair segment with increased resolution and high performance of only 0.3° electrical INL!

  • Embedded Boards

    UltraZed Family - AVNET

    Embedded boards are boards with processors, multiple integrated circuits, interfaces and other essential components assembled on it to serve a dedicated function. Embedded boards comprise multiple technologies, including processors, core logic, networking, connectivity, and multimedia components to provide functionality and performance for embedded system design applications. Embedded boards and solutions are normally employed to ensure a faster time to market for the developer. Applications of embedded systems vary from tiny portable devices, to large commercial and industrial installations, and even largely complex systems like medical or military or aviation purposes. Embedded boards can have single MCU chip or multiple MCUs depending on the complexity of application.

  • Mobile Network Emulator

    Qosmotec Software Solutions GmbH

    QPER Mobile Network Emulator enables engineers to simulate handover scenarios in mobile networks without a fully-fledged test lab. Based on Qosmotec’s QPER technology, it allows to test UE and SIM-Card behaviour in a completely emulated mobile network: Cells can be configured with all relevant cell parameters (MCC, MNC, LAC, CI, etc.), SIMs can be added to the HLR, and UEs can use standard circuit switched and packed switched services. Thus, the QPER Mobile Network Emulator emulates the all components of a mobile network – consisting of core and radio functionality – and creates RF signals. It supports GSM, GPRS and EDGE (900 MHz, 1800 MHz) as well as UMTS (2100 MHz).

  • Resolver Systems and Resolver Sub Systems

    TDSM - Computer Conversions Corporation

    The TDSM Series are low cost absolute encoders consisting of a size 11 electromagnetic transducer and a 2.6 x 3.1 x .6 conversion module. The outputs available are 12 to 16 bit binary format representing 0 to 359.99 degrees of absolute shaft angle input. The transducer reference supply is also included in the module which is designed for printed circuit mounting. A data transfer and data hold line are provided for simple computer or microprocessor interfacing. These features in addition to the latest digital circuitry techniques, make these encoders the best selection in today's applications where resolutions greater than 10 bits are required with ultra high reliability assured.

  • X-Ray And Gamma Detector Systems

    FAST ComTec GmbH

    The XR-100CR is a new high performance x-ray detector, preamplifier, and cooler system using a thermoelectrically cooled Si-PIN photodiode as an xray detector. Also mounted on the 2-stage cooler are the input FET and a novel feedback circuit. These components are kept at approximately -55 °C, and are monitored by an internal temperature sensor. The hermetic TO-8 package of the detector has a light tight, vacuum tight thin Beryllium window to enable soft xray detection. The XR-100T-CdTe represents a breakthrough in xray detector technology by providing “off-the-shelf” performance previously available only from expensive cryogenically cooled systems. The XR-100-CdTe is also suited for measuring gamma rays.

  • Four And Two-Port Multi-Protocol RS-232/422/485 M.2 Cards

    M.2-COM-4SM Family - Acces I/O Products, Inc.

    The M.2-COM-4SM family of cards feature high performance 16C950-class UARTs. Available in 4-port and 2-port versions, each port is capable of communication speeds up to 921.6kbps in RS-232 (differential modes support speeds as high as 3Mbps) and has 128-byte deep transmit and receive FIFOs. Large FIFOs protect against data loss in multitasking operating systems, reduce CPU utilization, and improve data throughput, while reducing or eliminating inter-character or inter-packet pauses. The advanced integrated circuit with pre-scalar supports a wide variety of custom baud rates, and any rates not otherwise achievable can be supported via a custom factory-installed crystal oscillator (up to 10Mbps!).

  • Four And Two-Port Multi-Protocol RS-232/422/485 PCI Express Mini Cards

    mPCIe-COM-4SM Family - Acces I/O Products, Inc.

    The mPCIe-COM-4SM family of cards feature high performance 16C950-class UARTs. Available in 4-port and 2-port versions, each port is capable of communication speeds up to 921.6kbps in RS-232 (differential modes support speeds as high as 3Mbps) and has 128-byte deep transmit and receive FIFOs. Large FIFOs protect against data loss in multitasking operating systems, reduce CPU utilization, and improve data throughput, while reducing or eliminating inter-character or inter-packet pauses. The advanced integrated circuit with pre-scalar supports a wide variety of custom baud rates, and any rates not otherwise achievable can be supported via a custom factory-installed crystal oscillator (up to 10Mbps!).

Get Help