Filter Results By:

Products

Applications

Manufacturers

Showing results: 1126 - 1140 of 2637 items found.

  • Motorized Potentiometer

    Mounting On Circuit Board Or DIN Rail - INELTA Sensorsysteme GmbH & Co. KG

    *PCB mounting*Suitable as: setpoint device or rotary actuator*Compact in design* Robust aluminium housing* Gear safety clutch

  • I²C/SPI Interface Device

    NI

    The I²C/SPI Interface Device is a master or slave interface for inter-integrated circuit (I²C), or master interface for serial parallel interface (SPI) devices. With plug-and-play USB connectivity, the I²C/SPI Interface Device is a portable solution to communicate with consumer electronics and integrated circuits. The I²C/SPI Interface Device can be physically located more closely to I²C/SPI devices than PCI interfaces, reducing I²C bus length and minimizing noise problems. The I²C/SPI Interface Device supports I²C rates up to 250 kHz and SPI rates up to 50 MHz, and it also includes eight general-purpose digital I/O lines for a variety of applications, such as configuring the address of I²C devices or toggling LEDs.

  • Linear regulated power supply with thyristor pre-regulation

    NTN - FuG Elektronik GmbH

    High efficiency Short circuit proof and unlimited operation with full current in short circuit condition voltage and current regulation with automatic and sharp transition; control mode indicated by LEDs Voltage and current setting with 10-turn potentiometers with precision scale; the adjusting knob can be locked 4 digit DVM for voltage and current (for table-top models) Sense terminals for the compensation of voltage drop on the load lines. The nominal voltage always refers to the output terminals Parallel and series connection possible Suitable for inductive and capacitive loads for 700 W nominal power and higher, limitation of inrush current on switching on Interlock loop to monitor the external load and internal loop as a standard for three phase units Elapsed-hour meter as a standard for three phase units

  • Broadband Detectors

    Pacific Millimeter Products

    These waveguide bandwidth detectors use silicon beam lead diodes on a planar stripline circuit to obtain an extremely rugged and compact device. Most millimeter wave broadband detectors have very poor VSWR due to the difficulty in obtaining a good wideband impedance match to the diode. To overcome this problem, these detectors utilize two diodes and an internal matched termination and 3 dB hybrid as shown below. This circuit allows a VSWR of 2.0 or better over a full waveguide bandwidth for most of these detectors. Detectors for waveguides WR-8 and smaller use a single zero bias GaAs diode. The high sensitivity zero bias GaAs diodes can also be special ordered for use at lower frequencies when highest sensitivity is required.

  • 3-Phase AC Voltage Transducer

    ENVIROMUX-PT3-600 - Network Technologies Inc

    Monitors and reports voltage of any 3 phase circuit. Remotely detect blown fuses or tripped circuit breakers. Three 600 VAC inputs, three 4-20 mA outputs. Inputs and outputs isolated from one another. Frequency: 50/60Hz. Maximum primary current: 600 volts. Accuracy: ±0.25% F.S. @60Hz. Output: 4-20 mA. "Zero" adjustment for accurate 0 VAC reading, and "Calibration" adjustment for frequency and voltage level. Powered by the ENVIROMUX-S420MA-24V. Regulatory approvals: UL, CUL, CE. Requires two ENVIROMUX-S420MA-24V to monitor three phases. Caution: installation should be performed by qualified electricians only. Make sure electrical service is disconnected before making any electrical connections.

  • Wireless Functional Test Fixtures

    Circuit Check, Inc.

    Circuit Check’s wireless fixture technologies reduce debug time, simplify ECO’s and reduce maintenance. This allows for the highest test performance, ability to probe denser smaller targets and achieve ultra-high node counts. Higher density more complex circuit boards complicate testing requirements. Smaller more tightly spaced test pads create a wiring challenge for the fixture fabricators, test engineers and maintenance personnel. Wireless fixtures solve the challenges associated with the nest of wires found in long wire fixtures. Wireless fixtures replace the “nest” of wires with copper traces on a multilayered printed circuit board called a Translator Board (T-Board).

  • Network Tools & Testers

    Tripp Lite

    Tripp Lite's Multi-Functional Network Cable Tester allows you to test wiring continuity for Cat5, Cat6, Phone and Coax cable assemblies. Identifies mis-wires, short circuits and open circuits. Features two piece transmitter and receiver, two BNC-F coax converters and coax terminator. Includes handy storage pouch when not in use. Power supplied by 9V Battery (not included).

  • Analysis via Fourier Transform Infrared Spectroscopy (FTIR)

    National Technical Systems

    Fourier Transform Infrared Spectroscopy (FTIR) is a standard technique used in the identification of contaminating materials on the surface of printed circuit boards (PCBs) and around the leads of electronic components (BGA, capacitors, resistors, inductors, connectors, diodes, oscillators, transformers, IC, etc.) on printed circuit assemblies (PCAs). Additionally, FTIR can be used for “simpler” identifications, such as determining a specific type of plastic or rubber compound.

  • Analysis via Fourier Transform Infrared Spectroscopy (FTIR)

    National Technical Systems

    Fourier Transform Infrared Spectroscopy (FTIR) is a standard technique used in the identification of contaminating materials on the surface of printed circuit boards (PCBs) and around the leads of electronic components (BGA, capacitors, resistors, inductors, connectors, diodes, oscillators, transformers, IC, etc.) on printed circuit assemblies (PCAs). Additionally, FTIR can be used for “simpler” identifications, such as determining a specific type of plastic or rubber compound.

  • DC In AC Clamp Tester

    M-800P - MULTI MEASURING INSTRUMENTS Co., Ltd.

    *Model 800P is the world’s first clamp meter which can detect smallDC current in AC circuit in addition to general AC/DC current measurement.*By using this clamp meter, DC offset surveillance can be madeeasily in the actual fields like as solar inverters, etc. and it is possibleto check if the DC component in AC circuit is less than 1% ofthe rated AC current or not, according to the regulation.

  • Current Probe for High-speed & High Power-density

    CWTMini50HF - Power Electronic Measurments Ltd

    For high-speed and high power-density power electronic applications. This higher bandwidth probe is ideal for measuring the faster current transients in today’s new semiconductor technologies where faster turn on and turn off times, higher blocking voltages and smaller circuits demand, smaller, higher temperature, faster current probes.

  • Fuse & Cable Locator

    PL500 - Di-Log

    Locate fuses/MCB’s and assignment to particular circuits Find breaks in cable quickly and effectively Trace cables in walls up to 40 cm Accurately sort cables Easy to use simply plug in the transmitter and trace cable with the receiver Includes sensitivity adjustment thereby maximising the accuracy of both tracing and locating

  • PCB Manufacturing

    PentaLogix

    SO-9001 and UL certifiedClass IIIRigid circuit boards up to 40 layers3-mil traces and 3.5 mil spacesMinimum Mechanical drill size 8-milMinimum Laser drill size 3-milBlind / Buried ViasControlled ImpedanceRoHS Compliant (all options available)High temperature, high frequency materialAluminum and other exotic material

  • PCI Express Cameras with high speed and resolution

    CB120MG-CM - XIMEA GmbH

    4K, compact, high speed camera for: Flat panel inspection (FPD), printed circuit board (PCB) examination, solar panel analysis, persistent stadium and border security, wide area surveillance, cinematography, sports and entertainment, 360 panorama, UAV and Autonomous, Unmanned vehicles, aerial or city mapping.

  • Portable Manual Probing Station

    Model W4.0 x L6.5 - D-COAX, Inc.

    This portable manual probing station is designed for a versatile, comfortable, and accurate operation on up to 4.0” wafers or 4.0” X 6.5” printed circuit board assemblies. This turn-key, manually operated probing station, model W4.0 x L6.5, is part of the D-COAX commitment to the test and measurement and PCB fabrication industries.

Get Help