Showing results: 271 - 285 of 592 items found.
-
Macom Technology Solutions Holdings Inc.
MACOM’s PIN switch and attenuator diodes provide broadband performance from 1 MHz to 70 GHz. Available in die form, SURMOUNTTM, flip chip, plastic and ceramic packaging. These products are excellent choices for your switch, limiter, phase shifter and attenuator circuit applications. These diodes are available in Silicon, GaAs and AlGaAs technologies.
-
PAS 9782/GEN -
Precision Analog Systems Co.
The PAS 9782/GEN is a VME based, eight channel function generator card. Each channel contains a Direct Digital Synthesis (DDS) chip that can be programmed to generate sine wave output signals. This DDS device is a Numerically Controlled Oscillator (NCO), employing a phase accumulator, a sine look-up table and a 10 bit D/A converter.
-
PAS 9883/GEN -
Precision Analog Systems Co.
The PAS 9883/GEN is a VME based, eight channel function generator card. Each channel contains a Direct Digital Synthesis (DDS) chip that can be programmed to generate sine wave output signals. This DDS device is a Numerically Controlled Oscillator (NCO), employing a phase accumulator, a sine look-up table and a 10 bit D/A converter.
-
EV 2.0 Series -
HORIBA, Ltd.
To address new requirements in Semiconductor, lighting devices, automotive components, flat panels, MEMS sensors, memory chips, and logic electronics processed in the industry using dry etch, cleaning and (PE)CVD, HORIBA has introduced a unique generation of sensor dedicated to Advanced Endpoint Control, Fault Detection and Chamber Health Monitoring.
-
WifiMETRIX -
Nuts About Nets, llc
WifiMETRIX is a new diagnostic tool used to analyze and test Wi-Fi networks. It is a handheld device that operates in stand-alone mode -- that is, it does not associate or connect with an AP. WifiMETRIX implements two important features -- AirHORN and WifiPROBE. The built-in Wi-Fi chip can perform both signal generation / packet injection (AirHORN) and throughput diagnostics (WifiPROBE) on each channel.
-
Analog Devices Inc.
IF and RF Receivers are designed for communications infrastructure applications. Wide input bandwidth and high sample rates allow digitizing close to the antenna. Various receiver architectures, such as zero-IF, IF sampling to direct RF receivers, are supported and available on chip post digital signal processing can be used to offset demands in the FPGA or digital ASIC and ease analog filtering.
-
PCChost 1420 -
Sycard Technology
Based on Texas Instruments' PCI1420 CardBus host adapter chip, the PCChost 1420 PCI-to-CardBus bridge provides the engineer with a platform to evaluate a high performance ACPI compliant CardBus bridge device. Contained on a single Peripheral Component Interconnect (PCI) bus card, the PCChost 1420 is compatible with a wide variety of PC and non-PC PCI hosts.
-
Macom Technology Solutions Holdings Inc.
MACOM offers the highest sensitivity avalanche photodiodes (APD) on the market to satisfy 10Gtelecom and datacom applications. Both front-illuminated and back-illuminated chips are available and usable from 1250 to 1650 nm for bit rates up to 11.3 Gb/s. Proprietary designs enable superior bandwidth, excellent temperature stability and high reliability to support market needs.
-
Blue Pearl Software Inc
ASICs and FPGA routinely have millions of gates with memories, transceivers, third party IP and processor cores. Problems can be time consuming and complex to debug in the lab and through simulations. Designers need verification tools that can identify problems quickly to reduce their verification and debug time before simulation, before synthesis, and definitely before burning chips in the lab.
-
7200 -
Chroma ATE Inc.
Among several factors for PV to achieve grid-parity, Reliability of the PV Modules plays an important role. Since its known that some of the cell defects such as edge chips/ flakes, bumps of cell surface were proved to be source of infant mortality of the c-Si PV modules, therefore, to detect those defects is very important for c-Si cell manufacturers.
-
T3Ster® -
Mentor Graphics Corp.
T3Ster (pronounced "Trister") is an advanced thermal tester from Mentor Graphics MicReD Products for thermal characterization of semiconductor chip packages. Superior to all other thermal characterization equipment on the market due to its speed and ease of use; its extremely accurate temperature measurements (0.01oC); and its 1 micro-second measurement resolution in time.
-
Vishay Intertechnology, Inc.
Types of capacitors manufactured by Vishay include tantalum (both solid and wet), ceramic (both multilayer chip and disk), film, power, heavy-current, and alumninum. Vishay is the number one manufacturer worldwide of wet and conformal-coated tantalum capacitors, as well as capacitors for power electronics. Vishay is also one of the largest manufacturers of molded tantalum surface-mount capacitors.
-
King Design Industrial Co., Ltd.
*Equipment conforms to IEC61730 MST12 specification.*Pre- or post-round can be selected for control wiring connection.*With weights block’s positioning pin is removed before test; and is inserted in the rear positioning hole for the remaining time.*Equipped with rings at both front and rear end; used to connect a rope and control the driving direction.*Use replaceable special cutting chip.
-
CurveMasterTM -
Hilevel Technology, Inc.
The CurveMasterTM delivers new price/performance efficiency to curve tracing and Failure Analysis. Curve trace has been a standard feature in our full-power chip tester for years, so the CurveMasterTM is built with today’s components and technology. With all new high-accuracy DC Parametrics, you’ll enjoy the most powerful curve tracer you have ever used.
-
Ironwood Electronics
Ironwood Electronics extended its high performance socket product line with smart features. Sockets are typically rated for 2K to 500K cycles. How do we know if the sockets are used for 100K or 200K insertions? Solution is electronic chip insertion counter. Our sockets can be integrated with electronics counter into the compression mechanism of the socket lid. A push button is exposed on the compression plate. Every time a chip is compressed, push button is actuated which in turn activates the electronic circuitry inside the lid. These activations are counted by the counter IC and displayed in LCD. Let’s say a contact element is rated for 2K insertions. After 2K insertions, this contact element will be replaced by new contact element. Now, the counter has to start the counting from the beginning. To achieve this function, a reset option is included in the electronics circuitry. When reset is actuated, LCD display will go to “0”.