Showing results: 796 - 810 of 1454 items found.
-
Applied Image, Inc.
Sinusoidal Target Arrays have been recognized as a superior test method for a variety of applications, from moiré contouring to reliable MTF Evaluation of materials, lenses, cameras, and electro-optical systems (Follow the hyperlink to learn about using Sinusoids for MTF eval). Sinusoidal Pattern Arrays are manufactured on two different materials for both reflective and transmissive applications. Because of the inherent limitations of reflective materials, the maximum spatial frequency of the reflective pattern arrays is limited to 20 cycles per mm, while the transmission film arrays are offered in various sizes up to 256 cycles per mm. In addition, the sinusoidal arrays are available in a Single Frequency Grating or with Multi-Frequency Gratings. If instead of continuous sinusoidal frequency, you are looking for a square wave frequency design, then look to the Ronchi Gratings page. Should you need to alter the size of the pattern or the substrate, fill out our Custom Test Targets and Charts form and start the conversation.
-
NI
Digital Modules for Remote I/O provide 24 V digital inputs or outputs and offer 1‐, 2‐, 3‐, and 4‐wire spring terminal connection options. You can use inputs as counters or standard digital inputs, and you can adjust filter time to improve measurement quality. Inputs can include a built‐in power supply for sensors. Output modules feature circuit and overload protection and can drive up to 500 mA per channel, up to 8 A per module.A remote I/O system consists of an EtherCAT bus coupler and individual modules mounted on a DIN rail. You control the Digital Module for Remote I/O from a NI real‐time controller. You can use remote I/O hardware to add low‐cost I/O for simple tasks while your controller handles advanced tasks such as image processing, motion control, and high‐speed or specialty measurements.
-
PR140 -
MadgeTech, Inc
The PR140 is built with a precision stainless steel pressure gauge. The data logger has an accuracy of ±0.03 Bar (±0.435 PSI), which can be achieved over a wide temperature range, from 20°C to +140°C(68°F to 284°F). The PR140 can be programmed to take readings as often as once per second (1Hz), and has non-volatile memory that can store up to 32,700 measurements.
-
MSR160 -
MSR Electronics GmbH
Four integrated analogue inputs, a high measurement rate of up to 1000/s per channel and its gigantic memory capacity, all packed into a small format are the key characteristics of the MSR160 data logger. The analogue inputs of the robust mini logger can be used for conventional sensors with analogue outputs (e.g. CO2, conductivity, pH etc). In addition, a multiple output switching power supply is also provided.
-
MachXO -
Lattice Semiconductor
*Up to 27.6 Kbits sysMEM™ embedded block RAM and up to 7.7Kbits distributed RAM*SRAM based logic can be reconfigured in milliseconds using JTAG port*IOs support LVCMOS, LVTTL, PCI, LVDS, Bus-LVDS, LVPECL, RSDS*Up to two analog PLLs per device that enable clock multiplication, division, and phase shifting*Available in TQFP, csBGA, caBGA and ftBGA packages
-
SS110 -
Electro-Sensors, Inc.
Features • Works with remote/external pulse frequency output sensor (NPN, PNP) • Setpoint ranges: 0.01-0.99 & 0.1-9.9 rpm • SPDT relay output • Monitors speeds down to 100 min. per rev • Dial-in calibration does not require power • Built-in start delay • DIN rail mounting simplifies installation • 115, 230 VAC (50-60 Hz) and 12, 24 VDC power options
-
THB SERIES -
Transducer Techniques, Inc
Our THB Series through hole donut load cells offer anoutside diameter of 1.50 inches and up to four different thru-hole diameter options per capacity range. These load cells are manufactured from heat treated 17-4 ph stainless steel. The sensing element incorporates bonded foil strain gages of the highest quality and are sealed for protection against most industrial environments.
-
Neff Instrument Corporation
Multiplexed amplifier-per-channel systems have a dedicated pre-amplifier for every channel and a single Analog to Digital Converter, ADC, for the system. Amplified and filtered analog signals are multiplexed to a post-amplifier and then presented to the ADC to be digitized. Significant benefits of the multiplexed amplifier-per-channel system are: Higher Throughput Rates, Improved Filtering, Higher Per Channel Sampling Rate, Sensor Isolation, Improved Channel-To-Channel Isolation
-
NI
PXI Ethernet Interface Modules equip PXI systems with high-bandwidth Ethernet-based connectivity with up to 40 Gb/s data rates per port. Featuring compatibility with industry-standard network and automatic cable polarity detection, these modules are ideal for high-performance data transfer and vision applications on the PXI platform. These modules have independent bandwidth to support two GigE Vision cameras with Power over Ethernet (PoE).
-
CPCI395 -
AcQ Inducom
The CPCI395 features 16 analog voltage outputs, integrated on the CompactPCI standard. Each output has a 12- or 16-bit resolution and a software programmable output range (0..+10V or -10..+10V). Control of the analog output is as easy as writing the binary equivalent to a dedicated register (per channel). Conversion takes place automatically. If desired, channels can be synchronized by presetting the channels and then give a simultaneous update command.
-
ATS9146 -
AlazarTech
ATS9146 is a 2-channel, 14-bit, 125 MS/s waveform digitizer capable of storing up to 128 Million samples per channel of acquired data in its on-board memory or streaming acquired data to motherboard memory. ATS9146 is a single-lane PCI Express (PCIe x1) Gen 1 card, which supports up to 200 MB/s bus throughput. ATS9146 is an ideal solution for many applications.
-
LA-Gold-16 -
TEAM SOLUTIONS, INC.
A maximum sampling rate of 1 GHz is available on all channels. The LA-Gold-16 has a large data buffer of 1 Mega samples per channel for sampling rates of up to 500 MHz on all 16 channels. The large buffer allows long capture times at high sampling rates. The digital logger function is for capturing very slow varying signals, e.g. room temperature.
-
ProDAQ 3511 -
Bustec Ltd.
The ProDAQ 3511 DAC function card is a high-density card that fits into ProDAQ VXIbus motherboards and LXI function card carriers. This high-density card contains eight independent 16-bit DAC channels. Each channel is equipped with its own DAC. Users can update the output of each DAC with up to 200 kS per second either directly via software command or from an onboard FIFO.
-
Brimrose Corp
Brimrose’s rugged and high-performing on-line NIR process spectrometers deliver fast-response and multi-component analysis for a variety of process applications for many industries, including pharmaceutical, food & dairy, chemical, polymer, petrochemical, agricultural, seed, pulp & paper, and olive & grape industries. The AOTF technology enables Brimrose spectrometers to scan very fast (up to 16,000 wavelengths per second) and without moving parts.
-
Apogee Instruments, Inc.
Accurate within 1.5 % across a pressure range of 15 to 115 kPa (4.43 to 34.96 in Hg). Long-term non-stability has been measured continuously indoors and in natural conditions (with sensors mounted inside a datalogger enclosure) for multiple sensors and is less than 0.5 % per year. Temperature effects on signal are less than 1 % across a wide temperature range (-20 to 50 C).