Showing results: 1201 - 1215 of 1454 items found.
-
Extech EC410 -
Extech Instruments Corporation
EC410 kit includes EC400 ExStik® Conductivity/TDS/ Salinity Temperature Meter, with sensor, protective cap, three calibration standards, (30mL bottle each), weighted base, 3 sample plastic cups, with caps, four 3V CR-2032 batteries, 48 in. (1.2 m) neck strap, and carrying case. Autoranging meter offers 3 ranges of measurements from tap water to wastewater and any aqueous solution. Automatic Temperature Compensation of 2% per °C. Data Hold, Auto Power Off and low battery indication. Internal memory stores up to 25 labeled readings for easy recall.
-
SafEye (Quasar 900) -
Teledyne Gas & Flame Detection
The Open Path Combustible system detects hydrocarbon gases by analyzing the absorption of radiation caused by gases in the atmosphere and comparing it to background atmospheric absorption. This is accomplished between a pair of units: a Flash Source and a Detector that can monitor a distance of up to 200 meters.Open Path Combustible Gas Detectors are robustly designed and can handle the toughest environments: 316L stainless steel housings that meet IP66/IP68 and NEMA 250 6P egress standards; circuit boards epoxy coated for protection; MIL-C-810C testing for humidity, salt, fog, vibration, mechanical shock and temperature extremes; and SIL-2 approval per IEC61508 is a final statement in reliability.
-
Oxygas 500 -
Teledyne Gas & Flame Detection
The Oxygas 500 compliments the Gascoseeker 500 with a similar performance, measuring % LEL and % volume flammable hydrocarbons, but with the addition of oxygen for either gas/air or gas/nitrogen/air purging. The Oxygas 500 has the following additional features; automated zero during start-up, manually selectable purge mode.The P-500 variant has an additional part per million (ppm) range of methane.The Oxygas 500 is easy to use with very simple training, as the operation of the instrument follows the operation of the purge cycle. The rugged design allows the Oxygas 500 to be used in harsh environments. The instrument is also fully compatible with our range of calibration software and equipment.
-
Magnetic Instrumentation Inc.
Helmholtz Coils are ideal for the measurement of Rare Earth (Samarium Cobalt, Neodymium) and Hard Ferrite permanent magnet materials (materials which exhibit a relative straight line demagnetization). Our standard Helmholtz Coils are for use with fluxmeters. The Helmholtz Coil measures the magnet sample as a single magnetic moment provided that the longest dimension of the magnet sample is less than one-third (1/3) the diameter of the coil system. By definition, the magnetic moment per unit volume is the intrinsic magnetization of the sample. With our calibrated Helmholtz Coil and Integrated Fluxmeter – and given the volume of the permanent magnet sample – the intrinsic open circuit operating B (Bdi) can be measured.
-
imc Test & Measurement GmbH
Whether it’s in a vehicle, on a test stand or monitoring equipment and machinery - imc data acquisition systems are easy to operate and will help you become more productive and profitable. Our products are suited for work in mechanical and mechatronic applications. They handle up to 100 kHz per channel, are compatible with almost all signal sources and sensors, and can measure nearly all physical quantities such as pressure, force, speed, vibration, noise, temperature, voltage and current. The spectrum of imc data acquisition systems ranges from simple data acquisition via integrated real-time calculations, to the integration of models and complete automation of test stands.
-
PI-41702 -
Pulse Instruments
The PI-41702 is a four channel bipolar DC Bias supply that can provide an output current up to 100 mA per channel. The output voltage ranges from –8 V to +8 V, and this card has special filter circuitry to reduce the output noise for those applications that require a low noise bias output. Additionally there is a ‘D’ type connector that allows the introduction of laboratory type supplies to reduce the noise further. To change from using the internal power supplies to external power supplies requires repositioning jumpers. The PI-41702 also has voltage and current sense for remote measurement of the voltage and current levels.
-
Focus-4000 -
Kyoritsu Testsystem Co., Ltd.
Programmable power supply（User can select big volume or high accuracy model）Fixed power supply (5V/12V/24V acceptable)High accuracy current measurement(MAX 2A) - FX710Voltage measurement MAX 16points(within +/-60V) - FX710Short relays 16pcs (MAX current 1A) - FX62024CH digital input output pins(8pcs per unit, IN/OUT setting) - FX700/FX71016 open corrector output for controlling external relays16 port (simultaneously 2 ports ) Oscilloscope channel for observing wave formCommunication function RS232C/GPIB（Standard）、CAN/LIN communication, Programmer(Options)Focus-2000Plus unique in-circuit Test（ICT）function
-
imc Test & Measurement GmbH
Whether it’s in a vehicle, on a test stand or monitoring equipment and machinery - imc data acquisition systems are easy to operate and will help you become more productive and profitable. Our products are suited for work in mechanical and mechatronic applications. They handle up to 100 kHz per channel, are compatible with almost all signal sources and sensors, and can measure nearly all physical quantities such as pressure, force, speed, vibration, noise, temperature, voltage and current. The spectrum of imc data acquisition systems ranges from simple data acquisition via integrated real-time calculations, to the integration of models and complete automation of test stands.
-
SCR ELEKTRONIKS
This equipment comprises of high current source for testing of circuit breakers with additional facility for temperature rise testing (thus incorporating testing for moulded case, vacuum & air circuit breakers as per IEC 60947-2). The system integrates a servo controlled source with closed loop current feedback to maintain the current constant. It has the necessary instrumentation for maintaining current at full load & other conditions arising in testing at high current. The bench has a PC based control system with temperature data logger (24 channel with ch-ch isolation amplifiers). The data logger displays as well as stores a set of temperature values with time.
-
DPM-99 -
Edgetech Instruments
The NFPA99 has mandated that for Med Gas systems the "dew point for locally compressed air shall be monitored and alarmed per 4-3.1.9.8 and 4-3.1.1.2(f) to protect from line pressure dew point rise to 39 degrees F (3.9 degrees C) from a nominal design of 35 degrees F (1.7 degrees C)." This safeguard was the foundation for the new Edgetech Instruments DPM-99 Med Gas Dew Point Monitor. This specifically designed monitor exceeds the requirements set forth by the NFPA and was a collaboration with AIRVAC Technical Services who are certified by P.IP.E as medical gas inspectors in all 50 US States.
-
783200-02 -
NI
Kintex-7 70T FPGA, 500 kS/s Multifunction Reconfigurable I/O Device - The USB‑7845 features a user-programmable FPGA for high-performance onboard processing and direct control over I/O signals for complete flexibility of system timing and synchronization. You can customize these devices with the LabVIEW FPGA Module to develop applications requiring precise timing and control such as hardware‑in‑the‑loop testing, custom protocol communication, sensor simulation, and high-speed control. The USB‑7845 features a dedicated A/D converter per channel for independent timing and triggering. This design offers specialized functionality such as multirate sampling and individual channel triggering, which are outside the capabilities of typical DAQ hardware.
-
783200-01 -
NI
Kintex-7 70T FPGA, 500 kS/s Multifunction Reconfigurable I/O Device - The USB‑7845 features a user-programmable FPGA for high-performance onboard processing and direct control over I/O signals for complete flexibility of system timing and synchronization. You can customize these devices with the LabVIEW FPGA Module to develop applications requiring precise timing and control such as hardware‑in‑the‑loop testing, custom protocol communication, sensor simulation, and high-speed control. The USB‑7845 features a dedicated A/D converter per channel for independent timing and triggering. This design offers specialized functionality such as multirate sampling and individual channel triggering, which are outside the capabilities of typical DAQ hardware.
-
782915-01 -
NI
Kintex-7 70T FPGA, 1 MS/s Multifunction Reconfigurable I/O Device - The USB‑7855 features a user-programmable FPGA for high-performance onboard processing and direct control over I/O signals for complete flexibility of system timing and synchronization. You can customize these devices with the LabVIEW FPGA Module to develop applications requiring precise timing and control such as hardware‑in‑the‑loop testing, custom protocol communication, sensor simulation, and high-speed control. The USB‑7855 features a dedicated A/D converter per channel for independent timing and triggering. This design offers specialized functionality such as multirate sampling and individual channel triggering, which are outside the capabilities of typical DAQ hardware.
-
779640-01 -
NI
The USB-6525 is an industrial, bus-powered USB I/O device that can automate even the most demanding applications. The solid-state relay outputs are ideal for controlling pumps, valves, motors, and various other industrial actuators. The USB-6525 features channel-to-channel isolated digital inputs that you can use to read from industrial digital sensors, and eight solid-state relay outputs featuring 60 VDC/30 Vrms switching voltage and 500 mA per channel maximum switching current. Using programmable power-up states, you can configure the initial output states in software to ensure glitch-free, safe operations when connected to industrial actuators.
-
CPCI-AD16 -
ALPHI Technology Corporation
The CPCI-AD16 module provides a 3U high performance data acquisition subsystem. The Local DSP can be used to simply move data samples to the CPCI bus or can provide processing functions such as limit checking, FFT’s, digitalfiltering, etc. Application software can be downloaded to the DSP via the CPCI interface. Instrumentation amplifiers provide over-voltage protection, gain and filtering on a per channel basis. Internal scan and trigger clocks are derived from either the CPCI bus clock or the local DSP clock. Dual 32 bit timers can programmed to pace the acquisition process. The CPCI-AD16 can also accept external scan and trigger signals from a front panel connector.
