Showing results: 1681 - 1695 of 3691 items found.
-
KT-6055A -
KILTER ELECTRONIC CO.,LTD
AC+DC 400KW3 3/4 digits LCD with max. reading of 199940mm large jaw diamterAuto power off,Auto RangeData hold functionDiode Test & Audible contimuity
-
56WS4 -
North Atlantic Industries
NAI’s 56WS4 is a conduction-cooled, 1,500 Watt AC/DC Power Supply that converts either 3-phase, AC input or +270 VDC input into a single DC output at 1,500 Watts.
-
56XS1 -
North Atlantic Industries
NAI’s 56XS1 is a conduction-cooled, 2,000 Watt AC/DC Power Supply that converts either 3-phase, AC input or +270 VDC input into a single DC output at 2,000 Watts.
-
Acksen Ltd
Data Loggers measure AC & DC circuits for Renewable Energy installations. Record directional flow of current, determine patterns when your system is importing or exporting to the grid.
-
Supracon AG
In the measurement setup of SQUID electronics (detector variant), the dc SQUID amplifies the small amplitude signals of the detector with a large bandwidth so that they can be further processed with conventional AD converters.
-
cBP-6418U -
ADLINK Technology Inc.
*1 Segment: 1 system + 7 peripheral slots*cPCI BUS: up to 64-bit/66MHz*Power connectors: ATX connector x 1 DC Screw terminals
-
IRIS Instruments
The Syscal R2 unit is a high-power system designed for DC electrical surveys applied to groundwater exploration, environmental studies, civil engineering, structural geology investigation and mineral exploration.
-
Mini-Circuits
RF/microwave interconnect and precision test cables for 50-Ohm and 75-Ohm systems from DC to 67 GHz with a wide selection of connectors including SMA, N-Type, F-Type, BNC, and 2.92mm!
-
FTI 1000 -
Focused Test, Inc.
The FTI 1000 tester consists of independent test channels that allow all DC and AC MOSFET parameters to be tested either separately, or in one handler insertion or prober touch-down.
-
64-VBF -
Viewpoint Systems, Inc
The 64-VBF 10th order Lowpass Filter is a dual channel filter with independent switch settable Cutoff Frequency (Fc). The filter has a linear phase DC accurate root raised cosine response. The unit’s differential inputs are built to withstand high DC over-voltages up to ±50 VDC and greater than ±100 V transients. Gain of the unit is 1 allowing for minimal insertion issues. The output can drive a high speed DAQ multiplexer with its fast settle and capacitive drive capability.
-
677B -
TREK, INC.
The Trek Model 677B is a high-voltage power amplifier/supply unit for precise control of output voltages in the range of 0 to ±2 kV DC or peak AC with an output current range of 0 to ±5 mA DC or peak AC. The Model 677B can be operated in one of two modes: as a high-voltage amplifier where it is configured as a noninverting amplifier with a fixed gain of 200 V/V, or as a high-voltage power supply which responds to front panel controls to command an exact output voltage or current.
-
Arduino Motor Shield Rev3 -
Arduino llc
The Arduino Motor Shield is based on the L298 (datasheet), which is a dual full-bridge driver designed to drive inductive loads such as relays, solenoids, DC and stepping motors. It lets you drive two DC motors with your Arduino board, controlling the speed and direction of each one independently. You can also measure the motor current absorption of each motor, among other features. The shield is TinkerKit compatible, which means you can quickly create projects by plugging TinkerKit modules to the board.
-
ACS723 -
SparkFun Electronics
The SparkFun Current Sensor Breakout is a high accuracy board that utilizes the ACS723 for moderate AC and DC current sensing applications. The ACS723 sensor uses a Hall effect sensor to output a voltage relative to the current flowing through the IP+ and IP- pins on the board. The advantage of using a Hall effect sensor, specifically, is that the circuit being sensed and the circuit reading the sensor are electrically isolated meaning that, although your Arduino is running on 5V, the sensed circuit can be operating at higher DC or AC voltages!
-
19036 -
Chroma ATE Inc.
Chroma 19036 is the industry's first wound component electrical safety test (EST) analyzer that combines the functions of impulse test, hipot, insulation resistance and DC resistance measurements. It has 5kVac/ 6kVdc high voltage output, 5kV insulation resistance, 6kV layer short impulse voltage and 4-wire DC resistance measurement that can comply with the wound components test demands by providing maximum 10 channels output for multichannel scanning tests to save time and labor costs.
-
455 -
Lake Shore Cryotronics, Inc.
The Model 455 digital signal processing (DSP) gaussmeter combines the technical advantages of DSP technology with many advanced features at a moderate price. DSP technology creates a solid foundation for accurate, stable, and repeatable field measurements. Advanced features including DC to 20 kHz AC frequency response, peak field detection to 50 µs pulse widths, DC accuracy of 0.075%, and up to 5¾ digits of display resolution make the Model 455 ideal for both industrial and research applications.