Showing results: 1771 - 1785 of 3691 items found.
-
TM-8155＋ -
Twintex Electronics Co., Ltd
★ Large LCD, 80000 count Dual-display, Analog bar 21 sets.★ 50 measuring functions, with basic DCV, ACV, DCA, ACA, Ω, CAP, Hz, TEMP, diode and Continuity measuring function, etc.★ 18 types of frequency, frequency up to 8MHz, 1800 waveform outputs, 1%~99% duty cycle★ Simultaneous measure (AC+DC), (AC+Hz), (DC+dBm), (dBm+Hz), (Hz+Duty), (℃+℉)★ Auto data update and refresh, auto data hold, auto peak hold.★ 36-hour dynamic record: MAG, MIN, AVG, MAX-MIN (RELΔ), (REL%), setting upper & lower limit, timing measurement★ AC measuring adopts highly accurate true RMS measurement, with testing frequency bandwidth and AC+DC measuring★ RS-232 interface
-
Bierer & Associates, Inc
The HI Pot Device is designed to Hi Pot de-energized 15kV class cables. The tool transforms 18 Volts from the battery to approximately 8,000 volts DC. When the battery is installed and the safety switch is in the closed down position, the unit is in voltage detection mode. The unit should be in this position when installing the device, as it will sound a warning alarm if you approach an energized source. When the safety switch is lifted and the toggle switch is switched up, the unit is in the Hi-Pot mode and the high voltage DC is being applied.
-
ACS723 (Low Current) -
SparkFun Electronics
The low current version of the SparkFun Current Sensor Breakout is a high accuracy board that utilizes the ACS723 for low to moderate AC and DC current sensing applications. The ACS723 sensor uses a Hall effect sensor to output a voltage relative to the current flowing through the IP+ and IP- pins on the board. The advantage of using a Hall effect sensor, specifically, is that the circuit being sensed and the circuit reading the sensor are electrically isolated meaning that, although your Arduino is running on 5V, the sensed circuit can be operating at higher DC or AC voltages!
-
40-549-001 -
Pickering Interfaces Ltd.
The 40-549 is a single pole power matrix module, suitable for switching inductive/capacitive loads up to 5A with 110VDC/250VAC hot switching and 400VDC/250VAC cold switching. It is available in single 16x4, single 8x8, dual 8x4 or single 8x4 configurations. Connections are made via a front panel 25 way D-type male connector. Power Matrix Modules are intended for switching heavy AC or DC loads or for slaving large external relays, contactors and solenoids. The module is suitable for applications requiring switching of either mains voltage or DC current.
-
Auto -
CanDo
The CANdo AUTO Module is a rugged, multi-purpose CAN bus module with a USB port, two precision analogue inputs & a DC power supply input. The module is capable of operating either connected to a PC, or in a standalone mode powered from a 12 or 24V DC supply, such as a vehicle battery. The module maybe used as an interface between a PC & a CAN bus, or between analogue sensors & a CAN bus, in standalone mode. In addition, the module maybe programmed to transmit fixed, periodic CAN messages automatically on power up.
-
Analytic Systems
DC Battery ChargersStep-Up & Step-Down DC Source Chargers and Equalizers These units provide up to 600 watts to charge a 12V or 24 V battery systems (1 or 2 banks) from a 12, 24, 32 or 36 volt source. The single-board design incorporates state-of-the-art switch mode technology for unmatched efficiency and ultra-quiet operation. Multiple stages of filtering reduce radiated or conducted noise to very low levels. All Series are capable of charging up to two independent banks of batteries.
-
8000 HVDM -
Standard Electric Works Co., Ltd
● True RMS measurement● For measuring solar, PV systems● Auto ranging● Bar-graph indication● Data hold function● 3000V DC Voltage measurement● 2000V AC Voltage measurement● AC mA/uA measurement● DC mA/uA measurement● Low battery indication ● Auto power off ● Low power consumption● Rugged and compact● Comply with IEC / EN 61010-1, CAT III 1000V IEC / EN 61010-1, CAT IV 600V● Comply with CAT III 1000V for the range of 0~1000V AC/DC
-
Mornsun Guangzhou Science & Technology
Mornsun AC/DC On-board Converter, one of the best-selling AC to DC converter power supplies, has a good market in the wholesale of AC to DC converter modules. On-board AC to DC converter modules are more frequently used in emerging applications. MORNSUN is expanding and enhancing its portfolio of board mount AC to DC converters to provide customers with a diverse selection of AC/DC converter module power supply in terms of package configurations (SIP, DIP, open-frame, chassis mount, etc.), input/output voltage options and multiple protections. These PCB mount AC to DC power converter modules cover power levels from 1W to 1000W, featuring compact size, standard or extra wide input voltage range, wide operating temperature range, high reliability, etc. Perfectly meet your design requirements for AC to DC converter power supply modules in different industrial applications.
-
SP -
PJ Electronics, Inc.
Surge / DC Hi-Pot testing capabilities. Tektronix TDS1002, 1 Billion Samples/sec, real time, programmable, storage oscilloscope plus a DC Hi-Pot Tester. DC Hi-Pot testing with dual LED panel meters that display direct read out of current and voltage, with overcurrent safety trip. This dual tester combo is still capable of testing 3 phase motors with or without rotors.
-
Simplex Inc
The Simplex Watt-Muncher is a small DC rated load bank used to test battery systems, AC to DC rectifiers and power supplies, battery chargers, UPS systems and DC generators. The Watt-Muncher provides a variable test load used to measure charge and discharge rates, response, stability and endurance. Corresponding calibrations and adjustments can be made while maintaining a constant, precise, resistive load on the power source.
-
BD Series -
EverBeing Int'l Corp
Best for DC and RF probing, the platen lift is designed for smooth raise and contact of your probes simultaneously to your device. It is ideal for probing multiple spots on your device, or through multiple devices.
-
PA-622 -
PINTEK Electronics
*Max. ±100A DCA*Resolution: ≧10mA*Bandwidth: DC~300KHz*Rise Time: 1.2 uS*Over Range Function*10mV/A, 100mV/A Range*Adaptor/Battery Input*Separating Design,Convenient Durable
-
DARE Electronics
Current sensors are designed to monitor the presence or absence of AC or DC current and are available in an assortment of standard & custom models with hermetic or gasket seal models designed to withstand severe environmental conditions.
-
CCI
*Combine Tx and Rx BTS outputs onto a common feeder*Available dual and double configurations*Optional second duplexer can be installed in same tray*DC Pass-Through*Low IM and insertion loss
-
EB Series -
EverBeing Int'l Corp
Comprehensive prober for DC and RF. The EB series contains features to step-up your usability to acquire the accurate data you need from your devices. It has a built in probe card slot.
