Showing results: 691 - 705 of 3691 items found.
-
FLIR CM46 -
Teledyne FLIR
The FLIR CM46 clamp meter is designed for commercial and residential electricians. Featuring both AC/DC measurement, the meter is equipped with a bright backlit display for use inside electrical panels. Accu-Tip™ technology delivers amperage measurements on smaller-gauged wires more accurately — to a tenth of a digit. The meter also offers MAX/MIN/AVG recording; measures DCµA, temperature, capacitance, and frequency; and has electrical field detection to help you determine voltage presence and relative strength of the field.
-
MPS-D+ series -
Matrix Technology Inc.
Voltage stabilitySource effect CV≤0.01%+2mVLoad effect CV≤0.01%+2mVRipple and noise CV≤1mV(rms)CC≤5mA(rms)Voltage temperature coefficient 150ppm/°CCurrent stabilitySource effect CC≤0.2%+2mALoad effect CC≤0.2%+5mACurrent temperature coefficient 500ppm/°C
-
CP-05+ -
KILTER ELECTRONIC CO.,LTD
Amorphous Alloy CoreRange:4A,5us,40A,5us,400A,5usBandwidth:DC~100KHz(-3db)Rise time:3.5μsLow battery indicationNoise level: 200mA Jaw size: 23mm(Max)Auto Zero at power onRelative Zero correctionSize 180mm(L) X 44mm(w) X 30mm(H)Weight: Approx 200g
-
2781 / 2781 T (True RMS) -
Kusam Electrical Industries Limited
* Jaw opening dia - cable of 40mm * 3¾ digit (4000 counts) LCD for accurate reading.* Overload protection on all ranges. * Data-hold facility * DCA zero button for accurate reading* Low battery indication* Auto power off* Accessories : Test leads, carrying case, manual, battery installed
-
44LS1 -
North Atlantic Industries
NAI’s 44LS1 is a 100-Watt Power Line Conditioner with holdup time that protects downstream DC/DC converters from transients, low voltage conditions, and power interruptions. This unit accepts +28 VDC input and provides 22.5 to 30 VDC at 100 Watts to all downstream DC/DC converters.
-
Series KLP -
Kepco, Inc.
The KLP is an entirely new laboratory grade power supply in which the voltage/current limits are automatically recalculated, forming a constant-power hyperbolic-shaped boundary between the voltage and current modes. This curve, which replaces the single max-power operating point of conventional power supplies, provides the user with a greatly expanded choice of maximum power volt-ampere combinations as illustrated in the diagram by points A to B to C. The constant-power limit of the KLP is 1200 watts.
-
44KS3-02 -
North Atlantic Industries
NAI's 44KS3-02 is a 72.5-Watt Power Line Conditioner with holdup time that protects downstream DC/DC converters from transients, low voltage conditions, and power interruptions. This unit accepts +28 VDC input and provides a single output at 72.5 Watts either 22.5 to 30 VDC with holdup time or +16 VDC without holdup time - to all downstream DC/DC converters.
-
1330 -
Topward
± 199.99mV, ± 1.9999V, ± 19.999V, ± 199.99V, ± 1200V, 5 Ranges
-
IT6400 Series -
I-TECH Electronic Co., Ltd
The unique bipolar voltage/current output makes IT6400 series can be used as a bipolarpower source or a bipolar electronic load. The battery simulating function isespecially applicable for development and high speed production testing ofportable, battery-operated products. IT6400 has ultrafast transient time lessthan 20 μs and resolut ion up to 1 nA. Its new designed speed shift modeachieves volt age/current fast rising and without overshoot, the rising time upto 150μs. Mean while, the waveform display function let the test be visible and simple. IT6400 series can be widely used in portable battery-operatedproducts test, mobile power pack test, LED test and other fields.
-
Supreme Instrument Laboratories
Calibrator for calibration and testing of A.C. Milliammeters, Ammeters, Voltmeters, and D.C. Microammeters, Milliammeters, Ammeters, Millivoltmeters and Voltmeters having following technical specification
-
PADS -
Ponovo Power Co., Ltd.
The energy feedback type programmable AC/DC power source with energy feedback unit equipped functions of voltage adjustable, frequency adjustable, harmonic controllable, low voltage ride through simulation etc.
-
National Technical Systems
Dielectric Constant is used to determine the ability of an insulator to store electrical energy. The dielectric constant is the ratio of the capacitance induced by two metallic plates with an insulator between them to the capacitance of the same plates with air or a vacuum between them. Dissipation factor is defined as the reciprocal of the ratio between the insulating materials capacitive reactance to its resistance at a specified frequency. It measures the inefficiency of an insulating material. If a material were to be used for strictly insulating purposes, it would be better to have a lower dielectric constant.
-
PLZ-5W/5WZ Series -
Kikusui Electronics Corp.
The PLZ-5W Series high performance electronic load is the successor to the highly respected PLZ-4W series, whilst still retaining the same high specification and build quality. Advances include a high visibility color display, low voltage operation from a minimum of 1 V to a maximum of 150 V. Programmable profiles of voltage/current can be applied (using the new ARB function, as used in LED/solar testing) in addition to the inherited 6 modes of operation: Constant Current, Constant Resistance, Constant Voltage, Constant Power, Constant Current + Constant Voltage, Constant Resistance + Constant Voltage.
-
IT8912E Series -
I-TECH Electronic Co., Ltd
IT8900 series high accuracy LED specific testing electronic loads can simulate the real output of LED lights with different characteristics.Their specific circuit can realize CR-LED mode, adjustable frequency, duty ratio PWM dimming output port (frequency: 20Hz-2KHz), I-pp/I-max measurement function can test current ripple and start up surge current of LED constant flow source. Voltage and current testing speed can reach 50KHz. IT8900 series provides CR-LED / CC / CV + CC / CR /CW and other working modes, built-in USB / RS232 / GPIB communication interface. Widely used in LED driver power dimming test.
-
Elektro-Automatik GmbH & Co.KG
Our programmable electronic loads are composed of an optimum mix of analogue- and digital technology (µ-controller/FPGA based). By combination of standardised electronic platforms out of a modular structure, we generate a large portfolio of electronic-load series, perfectly adapted in power, function, performance and cost to the numerous applications in industrial environment and R&D. EA programmable electronic loads are available in conventional technology (heat dissipating) and as “regenerative” loads. The latter allows, specifically under long-term testing condition (e.g. battery discharging) a full amortisation of its invested value by its energy-saving capability, similar as with Photovoltaic installations.