Showing results: 2011 - 2025 of 3691 items found.
-
TIA-527 -
Scitec Instruments Ltd
The TIA-527 balanced optical to electrical converter provides adjustable gain and a bandwidth of DC to 125 MHz. It is useful for coherent heterodyne detection applications, spectroscopy and similar applications for which the ability to discern small variations in signal strength in two optical paths is critical..
-
Mini-Circuits
Mini-Circuits is your complete source for bias tees, handling up to 4 Amps DC and covering 100 kHz to 12 GHz!Rugged coaxial modelsTiny surface mount packages as small as 0.15 x 0.15 inExcellent isolation50 and 75 Ohm models
-
PS48401 -
LXinstruments GmbH
The PS48401 is a programmable DC power supply in a 2-slot PXI/cPCI form factor. It features a fully isolated output capable of delivering 0-48VDC / 2A / 40W. It offers a programmable current limit and the ability to measure the output voltage and current under software or trigger control.
-
Festo Corporation
Voltage 0...250V DC, 230 V AC Cable length 0.3, 2.5, 5, 7.5, 0.2...10 m Plug connection M8, M12 / female thread M5 Electrical Via reed contact Contactless PNP, NPN Pneumatic.
-
ROM-Elektronik GmbH
Electrical DC fields are created by friction between different materials. Synthetics in particular result in unnaturally high charges, which lead to stress reactions such as in a thunderstorm. The electric field strength is measured in volts per meter (V/m) or the surface tension in volts (V).
-
TOMSAD
*on / off switch output section*two independent adjustable DC output*independent outputs serial and parallel*constant voltage and current*Low ripple and noise*four digit LED displays three*for 16 hours at full load*automatically search out
-
TOMSAD
*on / off switch output section*two independent adjustable DC output*independent outputs serial and parallel*constant voltage and current*Low ripple and noise*four digit LED displays three*for 16 hours at full load*automatically search out
-
Ingenieurbüro Mencke & Tegtmeyer Gm
The metrology systems enable the measurement of all DC and AC measurements of PV arrays and inverters as well as all the necessary environmental conditions such as irradiance, module, inverter and ambient temperatures and other meteorological measurements. Similarly, the measurement systems for use can in meteorology stations are used.
-
Pulse Instruments
Our CompactPCI series mainframes are industry-standard, open-architecture chassis with enhancements to support Pulse Instruments' clock driver and DC bias cards. The enhancements are transparent to the CompactPCI specification, and 3rd-party cards CompactPCI/PXI cards can be used in our mainframes without hardware or software modification*.
-
KHT 1000 -
Nagel Electronics
The calibrator KHT 1000C generates DC voltages and square wave signals of steep rising and falling edges up to ± 1000V. Optional positive or negative output voltage, so both polarities can be tested without reconnecting the probe. Rising and falling edges are identical.
-
Carl E. Holmes Company
Shown below is an Electrochlorination power supply with a 4/20 ma interface. Input is 240 VAC, 1 PH, 60 Hz. Output is 0 to 10.5 DC, 130 Amps. This power supply can be interfaced with a PLC system. These units are custom units, built to order.
-
Columbia Research Laboratories
Columbia Research Labs Accelerometer Switch is designed to interface with electrical or mechanical systems to control, safeguard against, or warn of undesirable variations in DC and low frequency acceleration. This sensor is available with a selectable switch point, a single or Bi-polar switch, and a choice of input power.
-
1998B -
Peaceful Thriving Enterprise Co Ltd
The 2 pole Voltage Tester provides a clear indication of AC or DC voltages levels via bright LED's from 6V to 600V. It is constructed in accordance with the latest safety standards and is ergonomically designed which is durable enough for both industrial and domestic uses.
-
PeakTech Prüf- und Messtechnik GmbH
An extremely practical component tester for LEDs and other components. The device outputs an automatically raised output voltage between 0 to 300 V DC, which adapts to the connected load so that the sensitive components are not destroyed. Particularly suitable for the service and repair workshop.
-
1251 -
Ballentine Laboratories, Inc.
The BLI Series of Micropotentiometers consist of a Model 1251 terminating resistor and a Model 1351 Thermoelement housing. These micropots are true RMS current to voltage converters for calibrating AC instruments. The NIST calibration range is from dc to 500 MHz (available to 1.2 GHz)