Showing results: 1561 - 1575 of 3695 items found.
-
Teraohm -
Metrel d.d.
Advanced, digital HV measuring instrument with maximum test voltage up to 5000v DC and resistance measuring range up to 5 T.
-
RP2060 -
Teledyne LeCroy
+/-60V offset permits the DC signal to be displayed in the vertical center of the oscilloscope grid with a high-sensitivity gain setting (maximum +/-800mV dynamic range).
-
RP4060 -
Teledyne LeCroy
+/-60V offset permits the DC signal to be displayed in the vertical center of the oscilloscope grid with a high-sensitivity gain setting (maximum +/-800mV dynamic range).
-
Precision Acoustics LTD
Our high-performance needle hydrophone system consists of a range of interchangeable PVdF needle hydrophone probes, a submersible wide-band amplifier and a DC coupler.
-
Holding Informtest
Is designed to measure and control the DC resistance, electrical capacity, insulation resistance of electrical circuits and check the electrical insulation strength of electrical circuits.
-
N2870A -
Keysight Technologies
The N2870A passive probe offers DC to 35 MHz and 1:1 attenuation factor, making this probe ideal for low-level signal measurements.
-
PA-699 -
PINTEK Electronics
*High sensitivity: 1mA, High frequency: 1.5MHz. They are all 10 multiple calculation. Calculation is not making mistakes.*Max measuring current: +/- 40A DC / 80 Ap-p*Max sensitivity: ≧1mA*Bandwidth: DC ~ 1.5 MHz*Rising Time: 0.23 uS*Overload indicator*1V/A, 0.1V/A 2 ranges selectors*Input power switching (priority circuit) and battery available*Dispatching design, high durability
-
PTE-100-C -
EUROSMC, S.A.
The PTE-100-C is a portable Universal test equipment for testing electromechanical, electronic, and digital relays. The equipment can output a variable current up to 250A, a variable AC Voltage up to 250V, a variable DC Voltage up to 350V. Also the unit incorporates a variable stabilized auxiliary DC Voltage supply up to 250V and a fixed AC Voltage output up to 110V, which can be variable with the PTE-FCF option.
-
IRS Systementwicklung GmbH
The main components of electrical and hybrid vehicles are the electrical motor and the battery. Furthermore, inverters convert the DC voltage of the battery into AC currents for the motor. Battery chargers convert the AC voltage from the grid to the DC voltage of the battery, DCDC-converters shift energy between LV and HV battery and power distribution units make sure, that all components including additional loads may be safely connected in the car.
-
SGS H & SGS V -
Shanghai Jiuzhi Electric Co., Ltd.
The sphere gap type SGS H or SGS V can be used for Impulse, AC and DC voltage calibration according to the IEC 60052 recommendation.The spheres are arranged vertically or horizontally, one being mobile. In the vertical version the mobile sphere is remotely adjusted by using an electrical drive. In the horizontal version, both spheres are mounted on columns of insulating materials, hence enabling to superimpose impulse AC and DC voltages.
-
Model 227 -
Telebyte, Inc.
FEATURES: DataSpy Status Display; Full Duplex to 5 Miles; Async, DC to 115.2 KBPS; Powered by TD; RJ-11 and Screw Terminals for the Line Interface; Built-in Surge Protection; Fully Compatible with Model 201 up to 19.2 K. The Model 227 RS-232 High Speed Line Driver with LCD Display provides full-duplex transmission from DC to 115.2 KBPS over two twisted pairs.
-
CHA20 -
dfv Technologie
This digital chronometer enables the user to measure the time between two pulses generated either by a dry contact, a TTL input or an AC or DC voltage.
-
265 -
Summit
4000 Counts Display. Data Hold. AC/DC mV Range (DC mV Accuracy: 0.3% + 5digits). Capacitance (Max 4mF). Frequency (50MHz)
-
CP 1000 -
GMC-I-PROSyS
The CP 1000 current probe has been designed for use with multimeteres respectively for accurate, non-intrusive measurement of AC, DC and complex waveform currents.
-
CP 1005 -
GMC-I-PROSyS
The CP 1005 current probe has been designed for use with oscilloscopes respectively for accurate, non-intrusive measurement of AC, DC and complex waveform currents.