Showing product results. 1 - 15 of 389 products found.
-
MTG3,MTG5 - D.Marchiori s.r.l.
D.Marchiori (DMA) design and manufacture various models of Tilt Tables which provide very accurate position and motion control for testing and calibrating attitude/heading and inertial reference units. Tilt Tables can be supplied with different diameter support tables. Tilt tables can be controlled either by an internal computer or by an external PC connected via RS232. Tilt Tables are equipped with fast zero position finder. Speed, acceleration and position can be set independently for each axis.
-
ETS Solutions
ETS Solutions slip tables are designed to provide the optimum test platform for horizontal testing with any shaker combination. Two types of slip table are available to the user; a Unibase concept provides a structural steel body to align the shaker and table on a rigid platform, while a standalone slip table design allows the feasibility of any vertical shaker from ETS or other manufacturers to couple with the slip table assembly.All slip tables are designed with a precision ground natural granite slab with a selection of guidance bearings to meet different applications and budgets. Slip tables can be provided in almost any size from 12 in (300 mm) square for small shakers to 8 feet (2.5 meter) square for the larger shaker systems. Different types of restraining bearings are available to meet different application requirements and operating budgets.
-
Inframet
The primary goal of a well designed optical table is to eliminate relative motion between components of test system located on the surface of the optical table because such motion can generate measurement errors.
-
BT Series 900-1200 - ETS Solutions
The BT Series design provides a high over-turning moment and cross-axial restraint. This concept combines a standard slip table assembly with 3,000 psi hydrostatic bearings to provide high dynamic moment restraint while preserving the damping characteristics of an oil film. This system allows testing of heavy products with high centers gravity by reacting moments through the hydrostatic bearings. Cross-axis motion is constrained and is typically less than 10% of input at frequencies up to 2000 Hz. except at resonance. Additional hydrostatic bearings can be supplied to provide extra restraint when testing parameters require a higher overturning moment. The BT Series Hydrostatic Slip Tables can be configured to any size or shape and are available with any ETS Unibase shaker for any existing single and multi-shaker installation.
-
BT Series 1300-1500 - ETS Solutions
The BT Series design provides a high over-turning moment and cross-axial restraint. This concept combines a standard slip table assembly with 3,000 psi hydrostatic bearings to provide high dynamic moment restraint while preserving the damping characteristics of an oil film. This system allows testing of heavy products with high centers gravity by reacting moments through the hydrostatic bearings. Cross-axis motion is constrained and is typically less than 10% of input at frequencies up to 2000 Hz. except at resonance. Additional hydrostatic bearings can be supplied to provide extra restraint when testing parameters require a higher overturning moment. The BT Series Hydrostatic Slip Tables can be configured to any size or shape and are available with any ETS Unibase shaker for any existing single and multi-shaker installation.
-
BT Series 1600-1800 - ETS Solutions
The BT Series design provides a high over-turning moment and cross-axial restraint. This concept combines a standard slip table assembly with 3,000 psi hydrostatic bearings to provide high dynamic moment restraint while preserving the damping characteristics of an oil film. This system allows testing of heavy products with high centers gravity by reacting moments through the hydrostatic bearings. Cross-axis motion is constrained and is typically less than 10% of input at frequencies up to 2000 Hz. except at resonance. Additional hydrostatic bearings can be supplied to provide extra restraint when testing parameters require a higher overturning moment. The BT Series Hydrostatic Slip Tables can be configured to any size or shape and are available with any ETS Unibase shaker for any existing single and multi-shaker installation.
-
BT Series 600-800 - ETS Solutions
The BT Series design provides a high over-turning moment and cross-axial restraint. This concept combines a standard slip table assembly with 3,000 psi hydrostatic bearings to provide high dynamic moment restraint while preserving the damping characteristics of an oil film. This system allows testing of heavy products with high centers gravity by reacting moments through the hydrostatic bearings. Cross-axis motion is constrained and is typically less than 10% of input at frequencies up to 2000 Hz. except at resonance. Additional hydrostatic bearings can be supplied to provide extra restraint when testing parameters require a higher overturning moment. The BT Series Hydrostatic Slip Tables can be configured to any size or shape and are available with any ETS Unibase shaker for any existing single and multi-shaker installation.
-
GT Series 900-1200 - ETS Solutions
GT Series oil film tables are designed with general-purpose V-Groove bearings, combined with a magnesium or aluminum slip plate. Oil is supplied through portholes in the granite slab and is dispersed throughout the underside of the slip plate. The oil film provides a low friction surface, a damping medium for restraint of resonances, pitch and roll moments. Yaw restraint is provided by the V-groove guide bearings combined with the armature guidance system. GT Series guide bearings are primarily designed for use with ETS Unibase shakers but are available for any existing or new shaker.
-
GT Series 600-800 - ETS Solutions
GT Series oil film tables are designed with general-purpose V-Groove bearings, combined with a magnesium or aluminum slip plate. Oil is supplied through portholes in the granite slab and is dispersed throughout the underside of the slip plate. The oil film provides a low friction surface, a damping medium for restraint of resonances, pitch and roll moments. Yaw restraint is provided by the V-groove guide bearings combined with the armature guidance system. GT Series guide bearings are primarily designed for use with ETS Unibase shakers but are available for any existing or new shaker.
-
GT Series 300-500 - ETS Solutions
GT Series oil film tables are designed with general-purpose V-Groove bearings, combined with a magnesium or aluminum slip plate. Oil is supplied through portholes in the granite slab and is dispersed throughout the underside of the slip plate. The oil film provides a low friction surface, a damping medium for restraint of resonances, pitch and roll moments. Yaw restraint is provided by the V-groove guide bearings combined with the armature guidance system. GT Series guide bearings are primarily designed for use with ETS Unibase shakers but are available for any existing or new shaker.
-
-
Probing Solutions, Inc.
Probing Solutions offers Vibration isolation tables made by Kinetics and TMC. To order a table, please call PSI at (775) 246-0999, or email sales@probingsolutions.com for a quote.
-
Kinetic Systems, Inc.
At Kinetic Systems, we’ve taken the guesswork out of selecting optical tables and vibration control equipment. Our honeycomb vibration isolation optical tables provide cost-effective solutions for virtually any application. For extremely sensitive applications in severe or unknown vibration environments, we recommend our highly damped 5300 Series honeycomb optical table with Active-Air vibration isolation. For normal or moderate environments we offer economical, broadband-damped tables such as our 5200 Series or 5100 Series with either Active-Air Isolators or Modular Rigid Supports.
-
CSTA Series - Unholtz-Dickie Corporation
Unholtz-Dickie introduced the Combined Slip Table Assembly (CSTA) in the late 1960''s to meet the demand for positive mechanical alignment between the shaker and its companion horizontal slip table. The challenge was to achieve this positive, permanent alignment feature without requiring an expensive seismic mass in the vibration lab floor. The original CSTA design has been continuously improved over the years and has now become the industry standard for permanently aligned, integral reaction mass slip tables.
-
TCB-1.3 - Cincinnati Sub-Zero Products
The TCB-1.3 benchtop vibration chamber is ideal for reliability testing of compact products and electronics. It may be used as a stand-alone vibration table for vibration testing or placed inside an environmental chamber for combined random vibration & temperature testing offering flexibility and greater return on investment.
