Tables
See Also: Vibration Isolation
-
Product
Back Plane Tester
-
This machine is used to test back planes used in telecommunications central stations. An operator loads a completed point to point wired back plane onto a retractable shelf on the front of the tester. Table continues and the disk falls through a hole into the bin. The shelf is pushed back into the machine where it is held in place by pneumatic operated clamps. Then a series of pneumatic cylinders sequentially insert a test card into each location in the back plane. A remote instrument performs a complete point to point continuity, short and hi pot test on all connections in the back plane.
-
Product
USB PD Test System
6050
-
Single Output USB PD USB PD basic version：the single-group test systemarchitecture is as shown in the table, 5302A AC Source, 3302F + 3310F series and9922-R Quick Charge Controller.
-
Product
Automotive
-
Radiometrics Midwest Corporation
A2LA accredited state of the art 10 meter, environmentally controlled, vehicle level, absorber-lined chamber is available to solve your EMC problems. Testing is performed on a 20-foot diameter turn table with a 25,000 pound capacity.
-
Product
MAXDIO Connect
-
The MAXDIO Connect panel is a 19 inch rack mount or table top device capable of delivering Push-Pull outputs controlled by Open-Gnd Discrete or TTL Discrete.
-
Product
Energy Saving System
ECO-Vibe neo
-
ECO-Vibe neo has been designed for an eco-friendly vibration test system. The test conditions with a vibration test system depends on a unit under test. Generally, the exciting force required for performing a vibration test can be calculated by the product of mass (e.g. test article, jig, table, etc.) and test acceleration. But, when the required exciting force is smaller than the maximum rated exciting force of the vibration test system, the field power supply that the constant current has to be continuously provided to produce the DC magnetic field constitutes a large part of power consumption compared with the drive power for the moving element. ECO-Vibe neo can reduce the power consumption by choosing the exciting force in this case. In addition, you can enjoy a reduction merit of the running cost from the first year when the system is introduced because initial cost is zero.
-
Product
Light Sources
LS 150 Xenon Arc Lamp Source
-
Model LS-150 is a Patented US Pat. No. 8116017 low cost, high output 150 watt Xe arc lamp based light source. The entire source, power supply, lamp, and optical compartment are housed in an extremely compact enclosure, 9 x 6 x 11 inches. The unit's base allows mounting on inch or metric spaced optical tables with the optics centered over the hole pattern to allow for easy integration with the rest of your setup.
-
Product
Cable Tray Kit For M9018B And M9019A
Y1218A
-
The Y1218A is a cable tray kit designed for the M9018B and M9019A. It can be used with both the rack mount kit and the rail kit but, the rail kit is not required. The kit includes a cable tray, feet for using the chassis on a table, and attachment hardware. An M9018B or M9019A that is racked using the cable tray uses 5U of rack space. The tray is compatible with the Y1217A Rack Mount Rail Kit, the Y1215B/C Flush Mount and Y1216A/B Recessed Mount Rack Adapter kits. This tray is not compatible with the Y1270A Front Panel Interfacing Kit.
-
Product
Meters For Contact Angle And Surface Tension
Contact Angle Standard
-
Optik Elektronik Gerätetechnik GmbH
The contact angle standard is a glass plate with images, representing sessile drops with different contact angles. The contact angle standard is manufactured by a high accurate lithographic process, so the images itself are very accurate according the given CAD-data. The Glass plate is placed on the measuring table instead of a real drop. The proof of the reproducibility of the contact angle measurement is performed by a repeated measurement of the object (sessile drop). For a correct test, the measurement must be performed, using the live video (not a frozen image). For a real sessile drop exists the problem, that it evaporates permanently. The result of the permanent evaporation is the permanent change of the contact angle. Therefore, the proof of the reproducibility of the contact angle measurement is not possible, using a real liquid, since the object changes permanently the contact angle!
-
Product
Additional Rotary Axis for High Precision Co-Ordinate Measurement Machines, ISO 10360 Part 3 Compliant
QuadSlimLine
-
Rotary Precision Instruments UK Ltd
Precision rotary axes specifically developed to increase the flexibility, productivity and efficiency of your CMM.Low profile rotary table with an extensive measurement range where typical applications include inspection of rotors, disks, blisks and gears.
-
Product
8-outlet power strip
PO-0848
-
8-outlet power strip 15 Amp, 125 Volts. These rugged, versatile strips provide real convenience wherever multiple outlet strips are required. Can be used with racks, consoles, production lines and lab tables. Mounting hardware included.
-
Product
Differential Pressure Transmitter Trainer
-
Unitech Scales And Measurements Pvt. Ltd
This table top model comprises of two pressure chambers. One for high pressure and another for low pressure. The two pressure chambers are fitted with pressure gauges. The differential pressure transmitter is connected to the two chambers. The pressure is built by a foot air pump. Digital instrument is provided to indicate the differential pressure with transmitter output.
-
Product
PCIe Oscilloscope Software Triggering and Decoding
-
The R&S®RTO2000,; R&S®RTO6 and R&S®RTP; oscilloscopes support triggering and decoding of PCI Express Gen 1.1 and 2.0 signals. In addition, the R&S®RTP supports Gen 3.0 signals. Users can set up decoding in seconds via the intuitive menu dialogs. For detailed analysis, results can be viewed as color-coded telegrams and/or in a table. Errors and other protocol-specific fields, such as TLP and OS are identified efficiently using the oscilloscopes' protocol trigger.
-
Product
12/24/36V Conductance Battery Tester
MBT200
-
Tests 12V heavy-duty auto, truck, commercial, and marine batteries and 12/24/36V starter and charging systems including 42V mild hybrid systems. Eliminate tester input errors by choosing between automotive/truck battery or small automotive type batteries. LED bar graph immediately displays battery condition upon pressing TEST button. No conversion tables needed for CCA, SAE, IEC, EN or Ah. 390 to 650 CCA range (auto) and 650 to 1700 CCA range (truck).
-
Product
3CH Gas Mixer
G-MIX 3CH
-
G-MIX is a versatile integrated system that can be easily used to create innumerable gas mixtures, the gas flows are accurately controlled by three MFCs (Mass Flow Controllers), each MFC has stored within its memory the calibrate tables for 10 gases different.
-
Product
IEC60335 Inclined Plane Test Table for Stability Test
CX-W600
-
Shenzhen Chuangxin Instruments Co., Ltd.
It's to determine the stability of electric appliances which are used on a table or on the floorin accordance with IEC 60065 / 1998-07 clause 19.1, IEC 60335-1 / 1991-04 clause 20.1, IEC 60601-1 /1988 clause 24.1, IEC 60950 / 1991 + Amendments, modified, clause 4.1.1,EN 60335-1 / 1994 and A11 / 1995 clause 20.1, EN 60950 / 1992 + Amendments up to 1997 clause 4.1.1,VDE 0700 Part 1 / 10.95 clause 20.1 and Part 3 / 3.96 clause 20.1, VDE 0730 Part 1 / 3.72 clause 20a,VDE 0805 / 11.97 clause 4.1.1Inclined Plane Device is used to test the stability of an apparatus that requires a surface in order to work.The device cosist of a surface and an angle adjusting device with 0- 15 °
-
Product
Computer Assisted Microhardness System
C.A.M.S.
-
Newage Testing Instruments, Inc.
The C.A.M.S. concept starts with a Newage microhardness tester (or competitive microhardness tester), such as our MT91 Series or MS-ZH Series with video camera, combined with our software, personal computer and any required accessories, such as a motorized X-Y-Z axis positioning table.
-
Product
Table Top Dispenser
Island Series
-
Island Series robots give you versatility to do simple, repetitive automation jobs. Work areas range from 300 mm x 400 mm to 400 mm x 400 mm. All Island Series robots are compatible with our line of precision dispensing pump systems: Precision Auger Pumps and Volumetric PCD Pumps. Who says with going to an entry level robot you need to compromise on dispense quality!
-
Product
MIL-STD-1760
M4K1553Px(S)-1760
-
The M4K1553Px(S)-1760 interface module for the multimode, multiprotocol, Excalibur 4000 family of carrier boards provide a complete solution for developing and testing MIL-STD-1760 interfaces and performing system simulation of the MIL-STD-1760 bus. The module handles all standard variations of the MIL-STD-1760 protocol.Each M4K1553Px-1760 multi function module contains 64K bytes of dual-port RAM for Data blocks, Control registers, and Look-up Tables. All Data blocks and Control registers are memory mapped, and may be accessed in real time. Each of the independent dual redundant M4K1553Px-1760 modules may be programmed to operate in one of three modes of operation: Remote Terminal, Bus Controller/Concurrent-RT, and Bus Monitor. In addition, modules 1 and 3 can be programmed to operate as Concurrent monitors, to modules 0 and 2 respectively.
-
Product
Meters For Contact Angle And Surface Tension
SURFTENS AUTOMATIC
-
Optik Elektronik Gerätetechnik GmbH
Automatic measuring instrument for contact angle and free surface energy with motorized pump, automatic drop placement and motorized specimen table (200 x 200) mm.
-
Product
Clover Honey 44 Ounces Quart Jar
-
44 Ounces of pure raw clover honey.Clover honey is what most people think of as being typical honey flavor and color. It is widely used "on the table." Clover is the most common nectar producing plant. Dutch White, Alsike, White Sweet and Yellow Sweet clover plants are the most important for honey production. Depending on location and source, Clover honey varies in color from water white to amber and has a mild, delicate flavor.
-
Product
Test systems
-
MG Products can supply a variety of test systems. These include the Extended Boundary Scan Test from JTAG Technologies, the functional test equipment integrated into a table or high configuration from Unites systems or the Cabinet Modular Test solution (CMT). We offer the right solution for every test setup.
-
Product
VisualIMPACT Software
-
CEAST VisualIMPACT software is designed to control CEAST Pendulums and Drop Tower Series, manage tests and offer a user-friendly interface when using the Data Acquisition System. It records force and absorbed energy data related to impacts, visualizes and helps analyze the results and calculates resilience. The operator is guided through parameters setup by means of tables describing strikers and specimens that are filtered according to the test type and international standard selected. In the case of instrumented tests, many possibilities for data analysis and visualization are made available. The results are shown through comprehensive and customizable graphs and can be filtered by break type (only specimens with a selected break type are shown). Working with groups of test, the software performs a statistical analysis, and the operator can pick and discard single test results. Different measurement units can be selected. It is possible to print reports and to export data totally or partially. Recent improvements include the possibility to set a number of user profiles, including graphic settings, default printing options, advanced parameters for data analysis and so on, switching quickly from one another when looking at results. The introduction of a new Data Acquisition System (CEAST DAS 64K) in the Impact product line has also triggered a number of new capabilities for the SW, which is now able to process a more comprehensive calibration file for instrumented tups and hammers and manage DAS configurations with a wider range of data acquisition channels.
-
Product
DUMMY BLOCK
STAG 10
-
Ideal requirements of release agent between billet and dummy block:Optimal adhesion to the substrate, Optimal anti-soldering power, No hazardous fumes/vapors development during use, Non-flammable at the effective temperature, No build-up, no interferences on run out table.
-
Product
Preamplifiers
-
A.H. Systems'' Preamplifier line is an excellent choice with a rugged design, no hassles with soldering your own power leads and they improve overall system sensitivity by at least 20 dB. All of A.H. Systems'' Preamplifiers come with a 12-volt (or 15-volt) DC regulated power source. A low voltage indicator confidently allows you to power the amplifier with your own external 12-volt DC battery. This makes it a convenient choice for field measurements. See table below for amplifier specifications.
-
Product
Shake Table Testing
-
Response Dynamics Vibration Engineering, Inc.
Shake table testing is often used in prototype analysis, failure analysis, shipping vibration testing and vibration sensitivity testing. We know what boundary conditions are vital for effective testing, how and where to instrument the system, how to deal with for off axis excitation (often not accounted for), and make the most efficient use of testing time. Let us have a look at your system and any specified vibration criteria before the shake test is designed. We can interpret the criteria, make sure it is applied appropriately, and make recommendations that will save valuable time and expense.
-
Product
Display
Data Processing and Result View
-
The program allows to simultaneously download multiple data files obtained by means of ZETLab programs, as well as to view and edit corresponding data in the graphic and table format.
-
Product
Coaxial Cable Termination Toolkit
ICFP
-
Ardent’s ICFP is a next generation coaxial cable termination toolkit for advanced system design de-embedding, de-bugging, and calibration. Designed for the lowest loss access to signal paths on an IC circuit footprint, this solution is a simple, cost effective alternative to expensive probers and x-y tables for Engineers who need to probe multiple signals at once.
-
Product
Workbenches
-
Scientech Technologies Pvt. Ltd.
We believe that very few testing requirements are identical. We have created Work benches that are flexible to accommodate any testing setup from general to industry specific requirements. The WorkBenches are ergonomically designed instrument panels in vertical position with sufficient table space for working.
-
Product
7 Tesla Optical Cryostat
OptiCool®
-
The OptiCool by Quantum Design is a new optical cryostat using an innovative design that puts the sample volume in the heart of your optical environment. A custom 3.8 inch bore, split-coil, conical magnet offers fields perpendicular to the optical table up to ±7 tesla. The highly integrated design means, even with a magnet, your sample isn’t buried inside a large cryostat, far away from the optics. Seven side optical ports and one top optical port allow for optical access to your sample from a wide array of directions.
-
Product
Automated Calibration
ORION
-
ORION automates the process of characterization and calibration of engines. It facilitates the calibration process by taking control of both the ECU calibration system and the test cell control system to run experiments as part of an automated calibration process. With connectivity to IAV’s EasyDOE, Mathworks’ MBC Toolbox and other DOE tools, ORION provides an extremely powerful environment for mapping an engine and generating the Engine Management System calibration tables. The modular design means the product can be configured to a users’ specific requirements and work practices, rather than having to adhere to rigid methodologies dictated by prescriptive software.
