Tables
See Also: Vibration Isolation
-
product
19-outlet power strip
PO-1968
19-outlet power strip 15 Amp, 125 Volts. These rugged, versatile strips provide real convenience wherever multiple outlet strips are required. Can be used with racks, consoles, production lines and lab tables. Mounting hardware included.
-
product
Adjustable Isolating Transformers
PeakTech Prüf- und Messtechnik GmbH
The PeakTech 2235 is a 2 in 1 laboratory isolating transformer with integrated DC power supply, which was designed with the aspect of high safety requirements for use in research, science and repair. The device has a dual adjustable DC, AC output, which can also be used for constant voltage or current and offers high stability and performance. The output voltage or the output current can be read exactly on two separate 3-digit LED displays and the fixed output supplies a voltage of 5 V. The device is protected against damage by overload and short circuit by reliable overvoltage protection and can be placed in a 19 ”rack installed or used as a table device (“stand-alone”).
-
product
5 Micron Wire Grid Polarizer
These wire grid polarizers are fabricated from 5 micron diameter tungsten wire, and have a choice of wire spacing down to 12.5 microns. They are suitable for use from approximately 50 microns (or 6 THz) to longer wavelengths. Please refer to the table below for the standard availability of wire spacing and frame clear aperture / outer diameter.
-
product
Easy-to-operate Interface
ANALYSIS 3P
ANALYSIS 3P (Professional Version) interface consists of main menu, toolbar, property bar, submenu, main display area, numerical table and status bar, which is easy-to-operate.
-
product
3-DOF Simulation Table
KRD60 series
KRD60 Series 3 DOF simulation table simulates various mechanical, electrical, and electronic products installed on ships, seaplanes, and other equipment to perform sway and tilt tests to determine the ability and structural integrity of the product to withstand severe sway and tilt requirements. The tilt test is mainly applicable to large-angle tilt caused by ship damage, manipulation, imbalance in loading and unloading, and wind. The sway test is mainly applicable to long-term swaying of the ship due to external forces such as wind and waves, which must be maintained normally or products that work reliably, and products that have a significant impact on their performance in a rocking environment.
-
product
Portable gear inspection- and 3D-measuring systems
ultimate independent measurement - on the production machine or on the shop-floor without rotary table
-
product
Parallel Electrode SMD Test Fixture, DC To 3 GHz
16196D
The 16196D surface mount devices (SMD) test fixture offers excellent repeatability and usability, with accurate correlation up to 3 GHz. 16196 series fixtures are custom designed to fit specific SMD sizes (see table below), and provide repeatable DUT positioning with reliable contacts to enable stable measurement results – reducing the possibility of operator-induced error. Traditionally, SMD inductor evaluation up to 3 GHz has been difficult to implement – now with the 16196 series, it’s easy to perform accurate and repeatable measurements.
-
product
Interface Module for Multimode, Multiprotocol Excalibur 8000 Family of Carrier Boards, a Complete Solution for Developing & Testing 1553 Interfaces
M8K1553Px(S)
The M8K1553Px(S) interface module for the multimode, multiprotocol, Excalibur 8000 family of carrier boards provide a complete solution for developing and testing 1553 interfaces and performing system simulation of the MIL-STD-1553 bus. The module handles all standard variations of the MIL-STD-1553 protocol.Each M8K1553Px multi function module contains 64K bytes of dual-port RAM for Data blocks, Control registers, and Look-up Tables. All Data blocks and Control registers are memory mapped, and may be accessed in real time. Each of the independent dual redundant M8K1553Px modules may be programmed to operate in one of three modes of operation: Remote Terminal, Bus Controller/Concurrent-RT, and Bus Monitor. In addition, modules 1 and 3 can be programmed to operate as Concurrent monitors, to modules 0 and 2 respectively.Each M8K1553PxS single function module operates either as a Bus Controller, Remote Terminal, or Bus Monitor.NOTE: the M8K1553PxS module is NOT compatible to the M4K1553MCH module.The M8K1553Px(S) comes complete with Windows software, a C-driver software library including source code and may be used with Exalt, Excalibur’s Analysis and Laboratory Tools, a Windows monitoring application.
-
-
product
General Purpose Coaxial Cables For Sensors
General purpose coaxial cables are used with single axis ICP® sensors. This table provides relevant specifications for four cable types. Type 002 is the most commonly used, but three other types are also available.
-
product
Table Top Thermometer Tripod
TTS-4
Table top tripod with adjustable viewing angle. For use with TH-5, Th-8 and BAT-12 Thermometers
-
product
Intermittent Fault Detection & Isolation System
IFDIS
The IFDIS™ uses patented Intermittent Fault Detector technology that simultaneously and continuously monitors every circuit path within a Unit Under Test (UUT) - such as a Line Replaceable Unit (LRU) chassis' interconnects - for intermittent continuity failures that occur for as short as 50 nanoseconds. This state of the art technology is combined with an environmental chamber and vibration table, which simulate the UUT’s operational environment and cause intermittent faults to manifest, creating a system that is unsurpassed in intermittent fault detection.
-
product
Linear Stages
A new set of motorized tables developed by Klocke Nanotechnik allows high strokes at small volumes. The modules are driven by the Nanomotor®. Loads of up to two kg can be moved over centimeters of stroke with down to 2 nm resolution. Manipulation in many degrees of freedom is possible without backlash. The modules NMT xx-L are longer, but thin like a pencil. In most of the NMT-modules position measurement systems can be included without increasing the size. The resolution of the position sensor is better than 10 nm. All NMT modules can easily be fixed onto each other. Very small connectors allow the exchange of a module without removing cables. The NMT-Zxx are modules for vertical movement. They have an internal load compensation to lift up loads. Nanomotor-Grippers and force sensors that can easily be fixed on these modules are available.
-
product
16 Thermocouples/RTD Ch
APCI-3200-16
18-bit resolution, 16-bit accuracyEach channel can be configured either for thermocouples/RTD or as an analog voltage input channel16 analog input channels for thermocouple typesJ, K, T, E, R, S, B, N - or 8 diff. analog input channels for the acquisition of resistance temperature detectors (Pt100)- or 16 SE/8 differential analog voltage input channels, ± 2.5 V8 independent current sources for resistance temperature detectors (RTD) and one current source for cold junction compensationCold junction compensation (on separate screw terminal board PX 3200)Gain and offset calibrationLinearisation through table and calculation for the thermocouple types J, K, T, E, R, S, B, N and RTDsProgrammable gain16-bit accuracy with sample rates of 20, 40, 80 or 160 Hz (other rates on request)4 digital input channels, 24 V and 3 digital output channels, open collector, isolated
-
product
Inspection System for high-power precise 3D X-ray CT
X-eye PCT225
Inspection System for 3D X-ray CT able to analyze defected area precisely by precise movement of axis with high polished Anti-vibration table. High-power X-ray Tube of max. 450kV and large area Flat Panel Detector of max.16 inches can be installed depending on the sample. Customized 3D CT equipment is available with selecting main parts by customers depends on their needs for size and material.
-
product
High Speed Spin Fixture
1571P Series
The Model 1571 High Speed Rate Table System is designed to provide a precision high velocity testing solution for the development and/or production testing of inertial packages or their components.
-
product
Linear Actuators
Electrak E150
Thomson continues its strong support of our current customers through our legacy product families. We encourage our customers to contact our sales application teams to discuss new and improved product offerings. See the table below for our recommended replacements for the Electrak 150 legacy actuator .
-
product
Parallel Electrode SMD Test Fixture, DC To 3 GHz
16196A
The 16196A surface mount devices (SMD) test fixture offers excellent repeatability and usability, with accurate correlation up to 3 GHz. 16196 series fixtures are custom designed to fit specific SMD sizes (see table below), and provide repeatable DUT positioning with reliable contacts to enable stable measurement results - reducing the possibility of operator-induced error. Traditionally, SMD inductor evaluation up to 3 GHz has been difficult to implement - now with the 16196 series, it’s easy to perform accurate and repeatable measurements.
-
product
Back and Forth Scratching Tester
WGQ-60
Shanghai Dean Electrical Co., Ltd
Executive standard: NEMA、JIS; Inspection standard: JB/T4279.15-2008Used to detect the scraping resistance of coating and cable insulation layer of flat wires of 0.800～5.600mm (narrow side) and the silk and enamel covered round wires with nominal conductor diameter of 0.100～5.000mm;Application of SCM control allows for fast operation and strong anti-interference capacity;Sample support table allows for parallel rise and fall, maintaining close contact between the entire plane with sample;Scratching needle is vertical to the paint scraping direction and parallel with sample supporting table;When film is scratched and the action current is ≥5mA, painting scraper would automatically stop scraping;LED would automatically display the number of scraping.
-
product
Single-Axis Rate and Position Tables
The wide range of potential customer specifications is accommodated by a number of standardized or customized tables. They are distinguished by differing electrical drive technologies (direct drive, belt drive), table tops, motion controllers (COTS, ACUTROL®3000e), and various options (table tops, temperature chambers, accessories).
-
product
5 Digit Programmable Speed/Velocity Meter
CM1-RL
CM1-RL series provides a simple economic programmable speed/velocity table, it 20.0mm, 5-digit LED display, press the key to set the display range and its anti-jamming design and reliable quality, simple installation, you can meet the needs of general measurement of speed/velocity.This instrument also has 2 group relay outputs, 1 analog output, or 1 groups RS485 (Modbus RTU mode) communication features three a (More features please refer to page description). Operation press the inner design, the more human-no action can be avoided, especially suitable for all kinds of machinery used.
-
product
Temperature/Humidity Testing
Quest has 14 environmental chambers ranging in size from 1 cubic foot to over 1,000 cubic feet, covering temperatures from below -100C to temperatures exceeding 200C. Our temperature/humidity test chambers include one of the largest walk-in chambers (15 x 10 x 8 ft) in New England, table top, high humidity, thermal shock, and high ramp rate test chambers. We can provide a wide range of temperature/humidity conditions on a variety of different product shapes and sizes, from extremely small to large products.
-
product
Tabletop Ionizing Transport System
90610-03610
The Model IT-7000 Ion Transport System is a self contained, compact table top ionizer capable of producing copious amounts of both positive and negative ions. The variable speed fan permits a gentle flow of ionized air, reaching a distance of up to 4 feet. A charged object, when passed through the ionization field, becomes neutral instantaneously. Inherently balanced, the Ion Transport System has a fail safe balance indicator to assure proper ionization output for ESD static control applications.
-
product
WiFi Traffic Generators
LANforge WiFIRE
wireless traffic generator is an excellent choice for testing Access Points and other WiFinetworks. The CT520 uses a modified Wireless driver for WiFi NICs based on the Atheros chipset. It cansupport up to 32 Virtual Stations. Each of the Virtual Stations has its own IP address, IP port space, MACaddress and routing table. The Virtual Stations can be assigned to communicate to a particular AccessPoint, use a particular SSID, and have a WEP (64 or 128bit) or WPA/WPA2 key assigned. More advanced802.1X authentication is also included. There is a single WiFi radio per CT520 but multiple LANforgesystems can be clustered together for more realistic radio interference patterns and increased trafficgeneration capability. The radio supports 802.11 a, b, g or n mode. Transmit power andchannel/frequency is configured on a per-radio basis. Most other settings are configurable per virtualstation
-
product
DC Blocking L-Band Splitter Combiner
PD5980
INSTOCK Wireless Components, Inc
PD5980 is an IP67 outdoor, weather resistant, DC blocking, eight way, RF broadband, 50 ohm, power divider, power combiner furnished with TNC coaxial connectors. The passive Wilkinson design passes RF, 10 MHz and DC current through one port, typically for powering an active antenna, with the other ports blocking DC. Max voltage rating at the DC blocked ports is 50 VDC. All wireless band applications in the frequency range from 698 to 2700 MHz are covered with best in class RF performance. The RoHS compliant PD5980 is a bidirectional device capable of 40 W max microwave input power level in both power splitter and combiner apps. See 8 way power divider input rating tables for additional power handling info.
-
product
Protective Cover, G12x, ITA, Aluminum
410112857
The G12x Aluminum ITA Protective Cover attaches securely to your ITA for easy and effective protection of contacts and modules. The cover snaps into place and enables smooth maneuverability of the ITA and enclosure over tables and other surfaces.
-
product
Rotameter Measurement Trainer Module
Unitech Scales And Measurements Pvt. Ltd
The setup is a table top module, it comprises of source and measuring tank. The measuring tank is made of acrylic material with gradation marked in liters. A small FHP pump is fitted to circulate the water. A rotameter with control valve is used to measure the flow rate. Digital timer is provided to note down the duration of flow and the volume of water is measured by the markings on the measuring tank to calculate the actual flow rate
-
product
Air Velocity Meter
400
Measure both pressure and air velocityRead the red figures directly in feet per minute of velocity - from 400 to 10,000 fpm No conversion tables needed for air at standard conditions. Read the black figures in inches of water column air pressure - from 0 to 10" w.c.
-
product
Rockwell Hardness Tester
Sinowon Innovation Metrology Manufacture Ltd.
◆ Semi-automatic intelligent Digital Rockwell Hardness tester, you can automatically test the Rockwell hardness and surface Rockwell hardness measurement；◆ Automatic variable load, automatic loading, automatic unloading, automatic conversion, automatic measurement；◆ Friendly human-computer interaction，5.2“colorful LCD screen direct display test force,loading time,conversion value and indenter type etc； ◆ Automatically calculate and display the measured value, the maximum value, the minimum value, the average value and the hardness value deviation, the display shows the resolution 0.1HR；◆ There are functions such as hardness upper and lower limit settings, tolerance alarms, data graph analysis, average and (single point) batch measurement modes；◆ Software compensation function, the machine can be ± 3HR software compensation, no need to open the top cover for mechanical adjustment;◆ With automatic hardness conversion function, according to ASTM E140 conversion, no need to check the complex hardness of the table；◆ Multi-language features, can switch Chinese, English, German, Portuguese, Turkish, Czech, Korean and other languages；◆ Built-in 2000 single data storage function and 1000 group packet data storage function, can view a single data and data analysis；◆ Optional Bluetooth wireless printer to print the measurement data, no need to manually record and write test data；◆ Optional Softhard data analysis software and Bluetooth receiver on the test data for the computer into and analysis；◆ Support FexQMS measurement of large data analysis and control software to enhance the whole plant process control, reduce material loss.
-
product
DC Blocking L-Band Splitter Combiner
PD5920
INSTOCK Wireless Components, Inc
PD5920 is an IP67 outdoor, weather resistant, DC blocking, two way, RF broadband, 50 ohm, power divider, power combiner furnished with TNC coaxial connectors. The passive Wilkinson design passes RF, 10 MHz and DC current through one port, typically for powering an active antenna, with the other port blocking DC. Max voltage rating at the DC blocked port is 50 VDC. All wireless band applications in the frequency range from 698 to 2700 MHz are covered with best in class RF performance. The RoHS compliant PD5920 is a bidirectional device capable of 40 W max microwave input power level in both power splitter and combiner apps. See 2 way power divider input rating tables for additional power handling info.
