Showing results: 2281 - 2295 of 2823 items found.
-
PHASCOPE PMP10 DUPLEX -
Helmut Fischer AG
Handheld gauge for rapid and precise measurement of duplex-coatings (for the simultaneous measurement of lacquer and zinc or of lacquer/Al)Probe ESG20 uses measuring principles according DIN EN ISO 21968 (phase sensitive eddy current); DIN EN ISO 2178 (magnetic induction); DIN EN ISO 2360 (amplitude eddy current).Delivery with PC software FISCHER DataCenter with the following functionality: Transferring and archiving measurement data, comprehensive statistical and graphical evaluations, easy creation and printing of inspection reports
-
J2101A -
PICOTEST Corp.
The injection transformer is presently the prevalent method for connecting the network analyzer to the circuit being tested, and is primarily used for control loop stability measurements. The goal of the transformer is to inject a signal into the control loop being measured, without impacting the performance of the loop. In order to accomplish this to a reasonable degree, The transformer is isolated and therefore is capable of floating on a high voltage, such as a Power Factor Corrector (PFC), which is often close to 400VDC. Measuring voltages that exceed the voltage rating of the FRA inputs require attenuation probes.
-
J2100A -
PICOTEST Corp.
The injection transformer is presently the prevalent method for connecting the network analyzer to the circuit being tested, and is primarily used for control loop stability measurements. The goal of the transformer is to inject a signal into the control loop being measured, without impacting the performance of the loop. In order to accomplish this to a reasonable degree, The transformer is isolated and therefore is capable of floating on a high voltage, such as a Power Factor Corrector (PFC), which is often close to 400VDC. Measuring voltages that exceed the voltage rating of the FRA inputs require attenuation probes.
-
BAT-12R -
Physitemp Instruments
The BAT-12R rechargeable laboratory digital thermometer is Physitemp's most popular and best selling instrument due to its versatility, quality construction and low cost. The BAT-12R has 0.1°C resolution and super accuracy of 0.1°C ±1 digit between 0-50°C, 0.1°C ± 1 digit over full range.The temperature range is -100 to 200°C. The BAT-12 provides fast readings, usually within 2-5 seconds depending on the temperature probe in use.
-
MR176-KIT6 -
Teledyne FLIR
Gain a competitive advantage with the advanced, affordable inspection tools in the FLIR MR176-KIT6. This kit includes the MR176, a powerful moisture meter with the flexibility to take either intrusive or non-intrusive measurements, and the E6, the ultimate thermal inspection tool for building, electrical, and mechanical applications. Easy-to-use, rugged, and field-ready, both tools are designed to help you find problems faster and give you that competitive edge. The kit also comes with a hammer/wall cavity probe combo for additional moisture measurement applications.
-
9355-1 -
Solar Electronics Company
Solar Model 9355-1 Pulse Generator is designed to provide impulse excitation by means of an injection probe placed around interconnecting cables or power wires. The unit uses a charged transmission line (50 ohms) to generate a pulse with less than 2 nanoseconds rise and fall time, and duration of approximately 30 nS, calibrated in a 50 ohm fixture to deliver up to 5 amperes at a rate of 30 p.p.s. for one minute as required by MIL-STD-461D/E, test method CS115.
-
SparkFun Electronics
The SparkFun Soil Moisture Sensor is a simple breakout for measuring the moisture in soil and similar materials. The soil moisture sensor is pretty straightforward to use. The two large, exposed pads function as probes for the sensor, together acting as a variable resistor. The more water that is in the soil means the better the conductivity between the pads will be, resulting in a lower resistance and a higher SIG out. This version of the Soil Moisture Sensor includes a 3-pin screw pin terminal pre-soldered to the board for easy wiring and setup.
-
WL MIDGET -
Walter G. Legge Company Inc.
WL MIDGET Surface Resistance Meter is an ultra-wide range, battery operated, portable instrument for measuring Surface Resistivity and Resistance to Ground of virtually any flat surface conforming to ASTM D-257 standard method by using recommended parallel bar sensing probe. Gives simple, repeatable measurements of conductive, static dissipative, and insulative surfaces. Ranging is automatic due to the use of high-speed OP-AMP Integrated circuits being linear, with changeover points +1/2 decade on a logarithmic scale. Repeatability equals + 5%.
-
J2180A -
PICOTEST Corp.
The J2180A low noise preamplifier provides a fixed, AC coupled 20dB gain while converting a 1 MOhm input impedance to a 50 Ohm output impedance. With a 3dB bandwidth of 0.1Hz to 100MHz, the preamplifier improves the sensitivity of oscilloscopes, network analyzers and spectrum analyzers while reducing the effective noise floor and spurious response. The preamplifier can also serve as a low frequency DC blocker for a spectrum analyzer or you can use it to connect a high input impedance oscilloscope probe to 50 Ohm equipment.
-
KT7193 -
Ketai instrument (kunshan) Ltd.
● 3 3/4 digits 3999 count● Extra high DC/AC current measurement● Data hold to capture measurements● Backlit display is easy to read under any light condition● AC current measurement up to 1500A● DC current measurement up to 1500A● DC/AC voltage, resistance, capacitance, frequency and temperature measurement● Diode and continuity test● Accessories included: 9V battery, carrying case, test leads, K typetemperature probe, English manual, gift box
-
52-50690 -
Longacre Racing Products, Inc.
Computes tire temp averages for temps just taken, recalled from memory, or you can even manually enter temps taken previously to compute averages. Advanced electronics stabilize your readings quickly giving you accurate, consistent results. Pyrometer comes with a built-in night light with auto shutoff, fast response coiled cord adjustable tire probe, and carrying case. It also features a built-in four car stopwatch with 75 lap memory for all 4 cars.
-
TK9LIN50 -
Techna-Tool Inc.
BK Mikro Linear is based on the existing design concepts for tool, object and free space monitoring and is modified to utilize a rack and pinion probe instead of a wand. This system monitors a specific distance or depth with longitudinal scanning. This is especially useful in cases where rotary scanning is inappropriateorimpossible. Some examples would be cavities, blind or through holes and places where space is limited. It can also be used to verify a part is in place during assembly or that the proper part is on the machine by probing a specific feature.
-
JW8101 -
Shanghai Joinwit optoelectronic Tech,co.,Ltd
JW8101 Series of Optical Power Meter is a new generation of desktop optical power meter developed by Joinwit.In addition to providing better dynamic range and linearity technical specifications, JW8101 also has rich menu design content, including threshold setting, alarm configuration, light splitting ratio, uniformity, additional loss and other functions.Detachable external optical power meter probe can meet the needs of optical device manufacturers, scientific research units and colleges and universities.
-
SmartSPM -
HORIBA, Ltd.
The SmartSPM Scanning Probe Microscope is the first 100% automated system that offers its cutting-edge technology of ultra-fast, metrological and high-resolution measurements for the most advanced materials research at the nanoscale in all AFM and STM modes. With the SmartSPM zooming in from large up to 100 µm overview scans down to atomic resolution has become a reality. Its design has been specially developed to be capable of being seamlessly integrated with optical spectroscopies (SNOM, Raman, Photoluminescence and TERS/SERS techniques).
-
Jackmark Engineering Ltd.
Guaranteed for a minimum of 100,000 connections, our rugged connectors are designed to meet your industrial & ergonomic demands in harsh testing environments. We offer numerous connector specifications all fitted with interchangeable spring loaded test probes. Supplied as a single hand held unit, panel mounted or fitted to a test lead, the combinations are limitless. Designed directly from your CAD data and thoroughly tested, our rugged & reliable connectors are used worldwide on a daily basis.