Showing results: 2746 - 2760 of 2823 items found.
-
Extech TM100 -
Extech Instruments Corporation
The Extech TM100 Type J/K Single Input Thermometer has a wide temperature range of -328 to 2501°F/-200 to 1372°C for type k and -346 to 2012°F / -210 to 1100°C for type j measurements. It has a high 0.1°/1° resolution and a large backlit LCD display with readouts in °F, °C, or Kelvin. The data hold function freezes the reading on the display and the screen displays the Max/Min/Avg. Readings capture a relative time stamp. Also, the offset key is used for zero function to make relative measurements. Auto power off with a disable feature. This thermometer comes complete with the Type K bead wire temperature probe and one 9V battery.
-
Protector Adjustable Family -
Test Electronics
Designed for testing heavy massive boards. Boards with heavy components like large transformers and inductors can destroy normal test fixtures. This design utilizes a 3 plate system where an internal lever actuated sub plate containing the test pins raises to probe the circuit board when the handle is pulled. Heavy boards can bend and break exposed test pins. Similarly large boards which need to be probed by very small delicate test pins can also benefit from this protected test fixture design. This fixture is recommended in situations where there is a high board mass to pin size ratio and pin protection is required. Front and rear panel modular inserts allow for easy updates and customizations to the user hardware interface.
-
Protector Edge Press Family -
Test Electronics
Designed for testing heavy massive boards. Boards with heavy components like large transformers and inductors can destroy normal test fixtures. This design utilizes a 3 plate system where an internal lever actuated sub plate containing the test pins raises to probe the circuit board when the handle is pulled. Heavy boards can bend and break exposed test pins. Similarly large boards which need to be probed by very small delicate test pins can also benefit from this protected test fixture design. This fixture is recommended in situations where there is a high board mass to pin size ratio and pin protection is required. Front and rear panel modular inserts allow for easy updates and customizations to the user hardware interface.
-
General Tools & Instruments
Two specifications tell you nearly everything you need to know about any infrared (laser) thermometer: its measurement range and its distance-to-spot (D:S) ratio. The wider the range and the higher the D:S number (a measure of its optical resolution), the better the instrument. Infrared Thermometers (IRTs) with lower numbers are perfectly adequate for simple tasks like spot-checking food temperatures and energy auditing such as the IRT207 Non-Contact Infrared Thermometer. Higher-priced infrared thermometers intended for industrial users may have a SKU that ends in "K" such as the IRT850K Ultra-Wide-Range Infrared Thermometer with K Port and Adjustable Emissivity. The "K" indicates that it can accept inputs from a "K" type thermocouple probe used to measure temperature on-contact.
-
Protector Press Rods Family -
Test Electronics
Designed for testing heavy massive boards. Boards with heavy components like large transformers and inductors can destroy normal test fixtures. This design utilizes a 3 plate system where an internal lever actuated sub plate containing the test pins raises to probe the circuit board when the handle is pulled. Heavy boards can bend and break exposed test pins. Similarly large boards which need to be probed by very small delicate test pins can also benefit from this protected test fixture design. This fixture is recommended in situations where there is a high board mass to pin size ratio and pin protection is required. Front and rear panel modular inserts allow for easy updates and customizations to the user hardware interface.
-
Test Coach Corporation
Test Coach offers Design for Test (DFT) consulting to assist customers with design review of prototype boards prior to release for production. Design for Test analysis is extremely important in ensuring that an assembly will achieve the highest possible test coverage. For ICT, this DFT will review the board to confirm that the bed-of-nails test fixture can be fabricated to test an assembly without sacrificing test coverage. As with ICT, Flying Probe benefits from DFT analysis by reviewing test point access and mechanical challenges that may affect the potential test coverage. Completing a DFT enables Test Coach to make recommendations to our customers that may be implemented on boards during the design phase which will allow for the most comprehensive coverage at time of test.
-
B-1027 -
ROSS ENGINEERING CORPORATION
Ross Engineering Corporation’s High Voltage Calibration Lab provides high accuracy capability for conducting tough reliability tests on all our high voltage devices. In this facility we test and calibrate HV Relays, HV Dividers, HV Probes, Spark Gaps, our Fiber Optic Systems, and HV Digital Voltmeters up to 450kV. We provide our own in house test lab to ensure Ross products meet or exceed required safety standards as well as our own high standards of dependability, long life and quality. Our technicians use test equipment calibrated by or traceable to National Institute of Standards and Technology or other national metrology institute to provide the highest in testing accuracy.
-
PRS-801RM -
Prostat Corporation
- Perform Point-to-Point and Resistance to Ground Measurements from 0.01 Ω to 200 Teraohms- Accuracy of ±2% from 1.00 Ω to 9.99x1010Ω- Measures in accordance with ESD TR53, ANSI/ESD S4.1, ANSI/ESD S7.1, ANSI/ESD STM97.1 and others- Constant Test voltages 10V and 100V meeting ANSI/ESD S20.20- Operates using a Rechargeable Li-ion Battery Pack- Takes Approximately 8,000 Measurements on a Single Charge (480 hours typical)- Stores up to 999 Test Values Into Memory- Compatible with Prostat Connect 2.0 for Downloading into Excel®- Charging and Download via Standard Micro USB Cable- Includes 5lb Conductive Probes and Carrying Case- Certificate of Calibration Traceable to NIST included- 2-year Limited Warranty on Main Instrument
-
Photo Emission Tech., Inc.
Solar Cell Testers are integrated systems incorporating Solar Simulator and I-V Measurement systems. PET offers Standard and Advance IV Measurement software. PET Cell Testers are capable of measuring a diverse range of solar cell parameters such as Isc,Voc, Imax,Vmax, Pmax, FF, Rsh, Rs and η cell conversion efficiency, complete light and dark I-V curves. All that needs to be done to test a cell is to load the cell, make electrical probes contact and press “Measure” icon on the I-V Measurement System software. The software will automatically open the Solar Simulator shutter, perform the test and close the shutter after the test is complete. The design is modular in nature and can be easily upgraded. Some options can added at a later time.
-
782718-01 -
NI
Non-Enclosed, 4-Channel, 51.2 kS/s/channel, ±5 V, C Series Sound and Vibration Input Module - The sbRIO‑9234 can measure signals from integrated electronic piezoelectric (IEPE) and non‑IEPE sensors such as accelerometers, tachometers, and proximity probes. The sbRIO‑9234 is also compatible with smart TEDS sensors. The sbRIO‑9234 delivers a wide dynamic range and incorporates software-selectable AC/DC coupling and IEPE signal conditioning. The input channels simultaneously measure signals. Each channel also has built-in anti‑aliasing filters that automatically adjust to your sample rate. When used with NI software, this module provides processing functionality for condition monitoring such as frequency analysis and order tracking. Non-enclosed modules are designed for OEM applications.
-
786471-01 -
NI
The FD-11634 can measure signals from integrated electronic piezoelectric (IEPE) and non-IEPE sensors such as accelerometers, tachometers, and proximity probes. The device also works with smart TEDS sensors, delivers a wide … dynamic range, and incorporates software-selectable AC/DC coupling and IEPE signal conditioning. The input channels simultaneously measure signals and have built-in anti-aliasing filters that adjust to your sample rate. This device is IP65/IP67-rated to be dust-tight and water-submersible and can sustain 100 g shock and 10 g RMS vibration in -40°C to 85°C environments. You program the FD-11634 with NI-DAQmx, which automatically synchronizes multiple FieldDAQ™ devices. When used with NI software, this device can provide processing functionality for condition monitoring such as frequency analysis and order tracking.
-
1550/1560 Series -
KANOMAX USA, Inc.
Kanomax Multi-Channel Anemometers are research-grade airflow measuring instruments designed for high performance and precision. When coupled with our highly accurate probes this four-channel anemometer provides highly accurate and reliable data readings. It features a LCD display that displays the data from each channel. The Our 1550 & 1560 models house module bays for the connection of up to 24 channels (model 1560) or 64 channels (model 1550) of simultaneous air velocity measurements. Each bay accepts one of five unique modules allowing for a wide variety of custom configurations for air velocity, temperature, and humidity measurement. For a larger system, you can connect up to 5 units in a cascade for up to 320 air velocity channels and transfer the data to your company computer.
-
Model 659 -
OAI
UV Light and Energy Meter for use with all wafer steppers. For over 45 years, OAI is a world leader in UV Light and Energy Measurement Instrumentation used for reliable accurate calibrated control of the photolithography processes in the Semiconductor, MEMS, Wafer Packaging and Wafer Bumping Industries. The New Model 659 is an advanced UV exposure analyzer specifically designed for use with all wafer steppers including high intensity wafer steppers. This meter averages up to 400 exposure readings, has Ethernet and USB interface for downloading recorded measurements, and has intensity range of up to 7,500mW/cm2. Probes are available in wavelength of 365nm, 400nm, 420nm & 436nm. OAI has a complete certified calibration lab to maintain the performance, quality and reliability of our meters. The Model 659 meter is traceable to NIST standards.
-
FIB -
JEOL Ltd.
An easy-to-use, out-lens type scanning electron microscope (SEM) equipped with a Schottky electron gun, as well as a new FIB column capable of large current processing (maximum ion current 90nA) installed into one chamber. JIB-4610F enables high-resolution SEM observation after high-speed cross-section milling with FIB, and high-speed analysis with a variety of analytical instruments, such as energy dispersive X-ray spectroscopy (EDS) that takes advantage of the Schottky electron gun delivering a large probe current (200nA), electron back scatter diffraction (EBSD) to perform crystallographic characterization, and cathodoluminescence (CLD). In addition, the 3D analysis function Cut & See is included in the standard configuration, allowing cross-section milling to be executed automatically at fixed intervals, while acquiring SEM images for each cross section.
-
DP802i -
Testech Group Co., Ltd
DP802i type X - gamma radiation detector - as a super humanized design and enhanced personal dose monitoring is mainly used for X, gamma rays and hard beta rays of radiation protection monitoring, suitable for nuclear power station, the accelerator, isotope applications, industrial X, gamma NDT, radiation source treatment, medical treatment, cobalt gamma irradiation, radioactive laboratory, nuclear facilities around environmental monitoring field, timely, ensure to my warning safety of staff; The instrument can be also measured dose rate and cumulative dose. It USES reactive new single chip microcomputer, the compensation for the probe, the instrument GM counting pipe has a wide measurement range, better energy response characteristics, and with overload directives and protection function.
