Showing results: 901 - 915 of 2820 items found.
-
8733 -
TEGAM Inc.
Multi-purpose probe for measuring air, liquids, soft materials, (e.g., water, ice cream, etc.). Compact size makes this probe easy to transport. The 403 stainless steel sheath is 3-3/4" long with a 2" handle. Thermoplastic rubber, coil-styled cord extends from 1-1/2 feet to 5 feet. Model 8733 is a Type K probe and Model 8753 is a Type T.
-
HP477DCR -
Delta OHM S.r.L.
Relative humidity and Pt100 temperature combined sword probe, with SICRAM module.
-
TP757 -
Delta OHM S.r.L.
Magnetic thermocouple type “K” probe for measurements on magnetic metal surfaces.
-
Langer EMV-Technik GmbH
The near field probe is designed for a high-resolution measurement of electrical near fields.
-
VB330 -
Bridge Technologies Co AS
The VB330 Probe is the flagship in the VideoBRIDGE product range. Equipped with up to two 10GB Ethernet inputs it is capable of monitoring thousands of streams in backbone networks and central head-ends. The VB330 utilises the same visual and intuitive approach to monitoring and analytics as other VideoBRIDGE probes.
-
N2891A -
Keysight Technologies
Use the N2891A 70-MHz high-voltage differential probe to make safe and accurate floating measurements with an oscilloscope. The N2891A differential probe allows conventional earth-grounded Keysight oscilloscopes to be used for floating signal measurements of up to ±7000 V of differential and common mode voltage.
-
TBCP2-250 -
TekBox Singapore Pte. Ltd.
The TBCP2-250 is a snap-on RF current monitoring probe. The probe has a very flat response with a 3dB bandwidth of 250 MHz and is characterized over the frequency range from 30kHz to 300 MHz. Upon request, it can also be supplied with a test protocol covering the frequency range 1 kHz to 350 MHz. The aperture of the RF current monitoring probe is 32 mm. Its transfer impedance is > 12 dB Ohm in the range from 700 kHz to 300 MHz.
-
HP3201 -
Delta OHM S.r.L.
Natural ventilation wet bulb probe with cable for WBGT measurement. Pt100 sensor.
-
DP0012A -
Keysight Technologies
The Keysight DP0012A is the 1 GHz model of the DP001xA Series differential active probes. These probes provide the superior general-purpose differential signal measurements required for many of today’s high-speed power-related measurements such as motor drives, automotive differential bus measurements, and high-speed digital system designs.
-
N2790A -
Keysight Technologies
Use the N2790A 100-MHz high-voltage differential probe to make safe and accurate floating measurements with an oscilloscope. The N2790A probe allows conventional earth-grounded Keysight oscilloscopes to be used for floating signal measurements of up to 1,400 V of differential voltage and 1,000 V of common mode voltage.
-
DP0010A -
Keysight Technologies
The Keysight DP0010A is the 250 MHz model of the DP001xA Series differential active probes. These probes provide the superior general-purpose differential signal measurements required for many of today’s high-speed power-related measurements such as motor drives, automotive differential bus measurements, and high-speed digital system designs.
-
DP0011A -
Keysight Technologies
The Keysight DP0011A is the 500 MHz model of the DP001xA Series differential active probes. These probes provide the superior general-purpose differential signal measurements required for many of today’s high-speed power-related measurements such as motor drives, automotive differential bus measurements, and high-speed digital system designs.
-
N2791A -
Keysight Technologies
Use the N2791A 25-MHz low-cost high-voltage differential probe to make safe and accurate floating measurements with an oscilloscope. The N2791A differential probe allows conventional earth-grounded Keysight oscilloscopes to be used for floating signal measurements of up to 700 V of differential voltage and common mode voltage.
-
Rotronic Measurement Solutions
The Insertion Probe is the part of the Inspection Camera that is inserted into the machinery in question. Also called an Insertion Tube, Insertion Probes are often subjected to deterioration and wear-and-tear from the inhospitable environments found inside industrial machines. Insertion Tubes can contain data cables, articulation cables, and sometimes even a Working Channel. Tungsten, Stainless Steel, and Polyethylene are the three most common materials used to coat Insertion Probes to make them crack resistant, puncture resistant, and even heat resistant.
-
ABET Technologies, Inc.
In this test solutions section of our website we describe the expanding line of Abet PV IV probe stations for the growing variety of solar cell types and sizes being developed around the world. This page describes a line of vacuum chucks and accessories for top/bottom, top/top, and bottom/bottom solar cells from 3 x 3 mm to 300 x 300 mm. Probe stations for multiple device on a single substrate and multifunction probe stations are described further in the sections highlighted to the left of this page.