Showing results: 481 - 495 of 2823 items found.
-
SPEA S.p.A.
SPEA’s Flying Probe Testers help manufacturers of printed circuit boards to deliver top-quality products in the fastest time-to-market, avoiding fixture cost and increasing accessibility when compared to bed-of-nails testers.
-
LPPHOT02 -
Delta OHM S.r.L.
Outdoor photometric probe for measuring ILLUMINANCE (0…150 Klux), CIE photopic filter, diffuser for cosine correction. mVdc output for klux. Complete with Calibration Report. On request 5 or 10m cables with connectors.
-
GB Inspection Systems Ltd.
GB Inspection Systems internally designs and manufactures a range of special single and twin crystal angle compression probes, giving the operator higher penetration in difficult materials such as large grain austenitic stainless steel.
-
PPTM01AS -
Matco Tools
*Connects with the new Power Probe Tek application for greater diagnostic functionality*The Maestro and Power Probe Tek App will be compatible to connect with a majority of diagnostic scan tools*Trace mode offers scope-like functionality*Stream and record visual traces of electrical issues found when diagnosing*DC voltmeter with the capability of applying battery supplied voltage or ground*AC voltmeter: TRMS, peak-to-peak/min/max, frequency, duty cycle*Resistance testing with a live or unloaded circuit*Fuel-injector test mode*Driver test for testing module drivers
-
Si-RM1 -
Sauermann Group
This Si-RM1 wireless pressure probe accurately measures high side and low side pressure.It measures relative pressure range from -1 to 60 bar and -14 to 870 psi and comes with wireless connection low energy.
-
LP471UVA -
Delta OHM S.r.L.
Radiometric probe for measuring the IRRADIANCE in the UVA spectral range 315 nm…400 nm, peak at 360 nm, quartz diffuser for cosine correction. For non-destructive testing ISO 3059:2001, EN 571-1, ASTM E1417.
-
Acculogic, Inc.
Flying probe test systems require no test fixturing, have few restrictions on board access, and can test boards with virtually unlimited number of nets. These systems also allow developers to complete test programs in a short time.
-
DPT-12 -
Physitemp Instruments
DPT-12 Immersion Probe for Liquids - 12'' #304 stainless steel welded shaft. Wooden Handle. Diameter is .3/16'' diameter. Immersible. Maximum temperature 350°C, Time constant 2 Seconds. 5 foot lead. Not isolated.
-
DPT-24 -
Physitemp Instruments
DPT-24 Immersion Probe for Liquids - 24'' #304 stainless steel welded shaft. Wooden Handle. Diameter is .3/16'' diameter. Immersible. Maximum temperature 350°C, Time constant 2 Seconds. 5 foot lead. Not isolated.
-
RNS International
With over 50 Tip-Styles, you can be certain we can help you find the right solution for your testing demands. And if we don’t offer a probe solution already in production, we will work together with you to develop a custom solution.
-
AUTO DIAGNOSTECH LTD
The probe can be used in 12/24 volt system with ECM/ECU either independently or used together with a diagnostic scanner to distinguish faults that lie in the sensor itself or the connection wires. The simulated voltage is used to emulate signals generated by different types of sensors.
-
TransData, Inc.
Abacus Electrics ANSI Type 2 optical probes utilize infra-red LED technology to provide a galvanically isolated, bi-directional communications interface between energy meters and laptop computers or handheld devices for onsite data retrieval, programming and diagnostics.
-
FS2361 -
FuturePlus Systems
The FS2361 is a logic analyzer probe used to test DDR3 DIMM memory. When used with the triggering and analysis capabilities of Keysight’s U4154/64 Logic Analyzer modules, it gives the user an extremely effective tool for debugging, testing and verifying DDR3 DIMMs.
-
FS2510AB -
FuturePlus Systems
The FS2510AB is a logic analyzer probe used to test DDR4 DIMM memory. When used with the triggering and analysis capabilities of Keysight’s U4154A/B/64A logic analyzer modules, it gives the user an effective tool for debugging, testing and verifying DDR4 DIMMs.
-
Laplace Instruments Ltd.
All commercial LISNs include an artificial hand connection and a transient limiter. This adds a 30dB insertion loss. A 30dB pre-amplifier is included which can be connected in the RF output feed to return the insertion loss to 0dB. The Voltage Probe requirement is covered by our PLIP (Power LIne Interference Probe). This fully meets the requirements of CISPR16, but has additional features:*Fully galvanic isolation between input and output (>1kV), for the safety of operator and analyser!*Shrouded safety clips for attachment to the line to be measured.*Filtered frequency response matched to Band A and B.*Current limiting on the output.*Visual indication of high voltage input.