Filter Results By:

Products

Applications

Manufacturers

Probes

enable access for closer investigation.

See Also: Test Probes, Microprobes, Test Point


Showing results: 2011 - 2025 of 2845 items found.

  • Clamp Meter

    ZHANGZHOU HUAYI ELECTRONICS CO.,LTD.

    Is an electrical tester that combines a basic digital multimeter with a current sensor. Clamps measure current. Probes measure voltage.

  • Energized Cable Sensor

    Hubbell Power Systems Inc

    The purpose of the Energized Cable Sensor is to allow the lineman to readily determine whether a URD cable is energized. The sensor consists of an amplifier which is designed to give a meter reading when the small AC voltage between the semi-conductive sheath and the concentric neutral of the energized URD cable is applied to the test probe. The amplifier is housed in a rugged phenolic case. Sensor may be used to check for energized condition on concentric-neutral cable below an elbow without test points. At cable mid-span (left), hose clamps bridge all strands of concentric neutral at the test location. Sensor’s neutral lead clips to one of the hose clamps. Tip on probe lead contacts only semi-conductive cable sheath to test for voltage presence.

  • Portable optical DO meter

    ARO-PR - JFE Advantech Co., Ltd.

    The Portable optical DO meter makes use of the fast-response optical DO sensor RINKO, maintaining its high-speed response performance (99% response < 7sec). The meter probe is equipped with a temperature sensor close to the sensing foil, and the measurements are made by simply inserting the probe into a DO sample bottle (the calibration is carried out using the National Metrology Institute of Japan (NMIJ) certified traceable gases standards). Differently from galvanic electrode sensors, the instrument does not require water sample stirring or fixing reagents, since there is no oxygen consumption. Thus, the required time to estimate dissolved oxygen is considerably reduced. The display unit shows the output instantaneously, and you can check the measured values in real time.

  • Pro-Stik II Level Sensor

    7330 - AMETEK Drexelbrook

    The Drexelbrook 7330 Pro-Stik II Series are intrinsically safe programmable liniear position sensors ideal for monitoring in a variety of liquids and tanks.These position sensors are based on the proven magnetostrictive technology and are available in different models including our popular explosion proof and flame proof models. The 7330 Pro-Stik II position sensors are loop powered and available with a rigid 316 stainless steel or flexible PVDF materials.The probe features a security feature by utilizing a timing sequence that is used to unlock the probe for programming. This ensures that the span cannot be accidentally programmed by someone in the field.All of the sensor's electronics are SMT components integrated into the 5/8" diameter sensing tube offering greater options for insertion and mounting in tanks and vessels.

  • UV Light Meter

    Model 308T - OAI

    Built for high intensity applications the NEW OAI Model 308T UV Light Meter is a dependable, direct-reading instrument designed for measuring UV light intensity for UV curing. The Model 308T features detachable probes for use in the UVA, UVB and UVC ranges, plus a high speed serial port. Accuracy of the meter is within ±3%and measurement repeatability is within ±3 LSB (least significant bit). Like all OAI precision instruments, the Model 308T provides NIST traceable measurements. This easy-to-use meter is auto-ranging from 0.1 to 1999.9 milliwatts/cm2 full scale when used with the 2000 milliwatts/ cm2 probe. The linearity of the meter in this range is at least ±(.002% + 6 LSB).

  • Clamp Meter

    ST-3347W - Standard Instruments Co., LTD.

    This clamp meter provides accurate AC, AC/DC current and voltage readings regardless of the waveforms. This meter can use in most industrial and commercial applications where non-linear loads distort the current or voltage waveform. Reliable operation. Features accessories such as test leads, carrying case and temperature probe.

  • Coordinate Measuring Machines

    NOVACAM Technologies, Inc.

    Novacam's 3D Non-Contact Coordinate Measuring Machines are designed with versatility and superior performance in mind: Precision (better than 1um) Speed (1-30 thousand measurements per second) Simultaneous dimensional and surface inspection Smallest probes measuring 0.9mm in diameter Automation by teaching with joystick Portability

  • MANUAL TEST FIXTURE KITS

    SERIES 5590 - Test-X Fixture Products

    Built with unique design features: Ease of assembly and disassembly All side panels are removable Side panel material is delrin for easy machining for connectors, switches etc.Light weight and durable construction2" Between Probe plate and lid plate allowing more room for tall board components

  • Photolysis Rate Analyzer

    PFS-100 - Focused Photonics Inc.

    , HONO, HCHO etc.) are key indicators for identify status & extent of photochemical pollution.The analyzer is receiving solar radiation by quartz probe and transferring the radiation to spectrum via optical quartz fiber, the spectrum data will be evaluated and compared with reference data with mathematical approach and gives photolytic rate.

  • Sonin Moisture Test Meter

    50211 - Sonin

    The Sonin Moisture Test Meter offers additional features & performance beyond those of the Moisture Test Tool. The meter’s contact probes are at the end of 3 foot coiled cable for detecting moisture in difficult to reach locations. Scale & reference chart correlate relative and moisture percentage readings

  • Universal Measuring Device For Magnetic Fields

    Teslameter M-Test MK4 - Maurer Magnetic AG

    The M-Test MK4 precisely detects and measures static or dynamic magnetic fields. The ~ 1 mm thick tangential probe allows precise, punctual measurements in hard-to-reach places, air gaps or on surfaces. The M-Test MK4 is particularly suitable for measuring permanent magnets or small ferromagnetic parts.

  • AFM-Raman for Physical and Chemical Imaging

    XploRA Nano - HORIBA, Ltd.

    Fully integrated system based on SmartSPM state of the art scanning probe microscope and XploRA Raman micro-spectrometer.Compact, fully automated and easy-to-use, the XploRA Nano concentrates the power of AFM-Raman into an affordable yet full-featured package, making TERS imaging a reality for all. The TERS proven system.

  • Precise 3D Profilometry

    µscan - NanoFocus, Inc.

    Using the NanoFocus µscan technology, you can measure up to 100 times faster than with conventional probe systems. Various µscan sensors are available for the different application areas. The optical profilometers of the µscan series are suitable for the fast scanning of surface profiles with precision in the low nanometer range.

  • Shaft Alignment

    NXA Runout Probe - ACOEM

    The NXA Runout Probe is a simple electronic tool designed to detect and measure shaft runout. The new tool represents a unique application of a linear variable displacement transducer (LVDT) to provide an easy-to-use but highly accurate measure of machinery problems that can confound the measurement and correction of shaft misalignment.

  • Water Restoration Contractor Kit

    Extech MO290-RK - Extech Instruments Corporation

    Use combination moisture meter/thermal hygrometer to capture all ambient conditions as well as moisture levels in one meter. Includes essential probes to measure moisture levels under baseboards, in between walls, and in hard wood and plywood subfloors. Use USB Humidity/Temperature datalogger for GPP calculations

Get Help