Pulse Instruments
Pulse Instruments is a leading manufacturer of systems and equipment for characterization and production test of CMOS, CCD and IR image sensors, including science-grade devices. Science teams have used Pulse Instruments systems to extract maximum performance from several HST CCDs, including the chip in the most recently installed Advanced Camera System that is providing 10x the performance of its predecessor.
- (310) 515-5330
- sales@pulseinstruments.com
- 22301 S. Western Ave.
#107,
Torrance, CA 90501
United States of America
-
Product
Pattern Generator
PI-2005
-
As a test engineer or digital designer you must have state-of-the-art tools to test, characterize and verify your complex semiconductor devices and digital circuit boards. The PI-2005 Pattern Generator will generate a wide range of simple or complex digital patterns for any test application that requires a serial or parallel digital data stream. To meet the requirements of complex devices and digital circuits, the pattern generator can be configured from 16 to 64 output channels.
-
Product
Four Channel Low-Noise DC Bias Card
PI-41702
-
The PI-41702 is a four channel bipolar DC Bias supply that can provide an output current up to 100 mA per channel. The output voltage ranges from –8 V to +8 V, and this card has special filter circuitry to reduce the output noise for those applications that require a low noise bias output. Additionally there is a ‘D’ type connector that allows the introduction of laboratory type supplies to reduce the noise further. To change from using the internal power supplies to external power supplies requires repositioning jumpers. The PI-41702 also has voltage and current sense for remote measurement of the voltage and current levels.
-
Product
Dual Channel Clock Driver Card
PI-41400
-
The PI-41400 is a dual channel Clock Driver card capable of operating up to 190 MHz into a 50-ohm load and up to 80 MHz at an amplitude of 8 volts into a 1-megohm load. Into a high impedance load the output voltage range is from a –3 volts to 8 volts with the output pulse amplitude ranging from 0.5 V to 9 V. When driving a 50 load the voltage range is –1.5 volts to 4.5 volts with the output pulse amplitude ranging from 0.25 V to 4.5 V. The rise and fall times of the output pulse are variable from 1.2 ns to 9 ns into a 50-ohm load and <5 ns to 9 ns into a HiZ load. The output pulse amplitude and the load being driven determine the range of variability. The driver output can be set for tri-state operation and the output polarity can be set for ‘Normal’ or ‘Inverted’ operation through software.
-
Product
Graphical Waveform Editor and Instrument
PI-PAT
-
Much more than just a visualization tool, PI-PAT is a full-fledged graphical waveform editor that allows you to spend more time testing and less time programming. PI-PAT doesn't require any programming experience or complicated syntax. Just draw or type patterns directly into the pattern window. Move a clock edge by dragging it. Adjust integration times by entering a single number. Change the output to your DUT by clicking the Update button. You'll never have to wrangle DSP or FPGA code with PI-PAT.
-
Product
Multi-Channel Data Acquisition System
PI-3105
-
This highly flexible system is designed to test a wide variety of imaging devices, from low-noise astronomy and medical devices, to military and machine-vision devices with GB/sec data rates.
-
Product
Dual Channel, Low-Noise DC Bias Card
PI-41701
-
The PI-41701 is a dual channel bipolar DC Bias supply that can provide an output current up to 100 mA per channel. The output voltage ranges from –8 V to +8 V and features programmable current limits with LED indicators and software interrupt to show/alert the user if the channel is in current limit. This card has special filter circuitry to reduce the output noise for those applications that require a low noise bias output.
-
Product
Instrument Mainframe
PI-11008
-
The PI-11008 Instrument Chassis was designed to accommodate the power and noise requirements of some of Pulse Instruments analog instrument cards. These instrument cards, such as the PI-41401, PI-41702 and others supply signal outputs that require more current from the -12 V supply than available in a standard chassis. Therefore this chassis has a larger -12 V power supply that provides 2.5 Amps.
-
Product
CMOS/CCD Production Test System
System 1828
-
The basic system consists of a 225 MHz pattern generator, 10 clock drivers, 6 DC biases, 1-4 channels of 10 MHz 14 bit analog data acquisition and/or 1-4 channels of digital acquisition. Additional options can be added to customize the system to meet your requirements.
-
Product
SystemSolutions
-
Whether your application is characterizing a massive mosaic of CCDs for the next great observatory, designing a faster FLIR for a weapons-guidance system, or production-testing a CMOS image sensor for a digital camera, Pulse Instruments can supply you with a fully-integrated test system that allows you to focus on your yourdevice, not on your test system.
-
Product
Dual Channel Tri-Level Driver Card
40465
-
Two channels of 10MHz drivers, that can be operated as standard Two-Level Drivers or operated as two channels of Tri-Level Drivers. In the Two-Level mode, the input to each driver channel requires one channel of TTL level timing. Tri-and four level modes require a second clock input. In the Tri-Level Mode, the output from lowest rail to high rail can be 18.5V. Like the 40460 the rise and fall time as well as the high and low voltage levels of each channel is programmable.
-
Product
Software
-
Test and Control Software is also available for several of our products. All of our software is designed by Pulse Instruments for optimum flexibility and control. Please fill out the following form to request an evaluation copy.
-
Product
Instrument Mainframe
PI-11006
-
The PI-11006 Instrument Chassis was designed to accommodate the power and noise requirements of some of Pulse Instruments analog instrument cards. These instrument cards, such as the PI-41401, PI-41702 and others supply signal outputs that require more current from the -12 V supply than available in a standard chassis. Therefore this chassis has a larger -12 V power supply that provides 2.5 Amps.
-
Product
GPIB Interface Card
PI-31000
-
The Pulse Instruments PI-31000 IEEE Interface Card is a standard GPIB Interface card offered by National Instruments. This interface card is used in applications where the PI-2005 Pattern Generator or other instruments are controlled from a remote system CPU, or it can be used as the system controller when the CompactPCI CPU is the system computer.
-
Product
Clock Drivers
-
Multiple timing signals ("clocks") are required by CCDs, IR FPAs, and some CMOS image sensors to transport electrical charge across the array to a sense amplifier for conversion into image data. Pulse Instruments offers a line of "clock drivers" for generating these timing signals. The parameters of these clocks (clock rate, pulse width, pulse amplitude, rise- and fall-times, etc.) greatly influence the behavior and performance of the imaging device. Our products take logic-level inputs from a pattern generator and allow the user to adjust the output parameters to suit their device and testing requirements. Clocks can be "tweaked" in real-time to determine optimal operating parameters for a particular device, or else programmed in accordance with a test plan for automated production test.
-
Product
Data Acquisition
-
For devices with analog outputs, we are now shipping our new multi-channel data acquisition system. This high-speed, low-noise solution is highly modular, so you can test scientific CCDs and high-speed machine-vision CMOS sensors with the same basic system. Swappable pre-amps and A/D converter modules enable you to reconfigure your test system to fit your needs.
