Defect
other than specified, imperfection .
-
Product
CapaConnect repair defective capacitive string parts
CC-LRP3/4+KS+DS
-
Hachmann Innovative Elektronik
With modules of CapaConnect series you can repair defective capacitive string parts of older installations, or retrofit string parts, where until now only direct cable taps are available. The connections to coupling dielectrics and earth can be carried out without an expensive dismantling normally, as the module contains all necessary components, like surge arresters, plug-in positions for adjustment capacities and high-quality contacts.
-
Product
Metal InspectionSystems
-
Metal surfaces must undergo a reliable inspection, because defects impair the functions of steel tubes or medical engineering products. Relying to the often appearing strong structures of such surfaces, special robust vision techniques are needed to make, for example, geometric measurements. Our systems are prepared to provide a fully automated, 100 % inspection rate in a rough industrial environment.
-
Product
Post-Mould Inspection Machine
IV-P1000
-
The IV-P1000 is a post-mould inspection machine best known for being a fully automatic vision inspection station and for having a user-friendly GUI for operator and recipe setup. This machine is best used to inspect packages for surface defects on top and bottom.
-
Product
MASK DR-SEM
-
Our defect review SEM tools perform detailed reviews of minute defects on photomasks.
-
Product
Manufacturing Defects Analyzer
eloZ1-1600
-
The eloZ1 Manufacturing Defects Analyzer is an in-circuit tester of the very latest generation, reliably detecting connection and assembly faults on printed circuit board assemblies. The eloZ1 can be integrated into table systems as well as into inline-systems.
-
Product
3D Sensor (Shiny Surfaces)
reflectCONTROL
-
reflectCONTROL is designed specifically to meet the high quality requirements that ensure high quality for shiny surfaces. The system based on deflectometry projects a striped pattern onto the measurement object. Defects on the surface cause deviations from the striped pattern which are recorded by cameras and evaluated by software.
-
Product
Software to Order
-
Our company develops turnkey technical vision systems, including writing software for specific tasks of the Customer, such as:- image capture- algorithms for localization and detection of objects- recognitionalgorithms - inspection algorithms, defect detection- logging and archiving- interface operator- programming FPGAs and controllersand much more
-
Product
Ultrasonic Flaw Detector
MFD500B
-
Based on ultrasonic principle, digital ultrasonic flaw detector MFD500B with 320*240 TFT LCD, it can test, orient, evaluate and diagnose various flaws such as crack, lard, air hole in workpiece’s interior swiftly and accurately without any destruction. It can be used in Laboratory as well as in engineering filed. With range of 0-9999mm, it can meet the requirement for general defect inspection in manufacturing industry, metallurgical industry, metal processing industry, chemical industry and so on. Low power design with large capacity and high performance lithium battery module, it can be long standby for months. High quality with low price, it is the first choice for the practical economic model for ultrasonic testing equipment.
-
Product
Photoluminescence Mapping System
VS6845A
-
Industrial Vision Technology Pte Ltd.
With its unique optical design technology, the System detects and classifies defects that affect yield and uses advanced photoluminescence (PL) technology to enable real-time monitoring of MOCVD production processes.
-
Product
Solder Paste Inspection Machine
3D SPI
-
The 6500 series is the measurement equipment provided by Jiezhi Technology for the small pads of solder paste printed on the PCB board. It will cause defects such as sharpness, offset, more tin, and less tin printing during solder paste printing. Causes defects in the later stage of production, this equipment can find problems in advance
-
Product
Semiconductor Wafer Microscope Inspection System
MicroINSPECT
-
MicroINSPECT Semiconductor Wafer Defect Microscope Inspection System combines state-of-the-art robotics, intelligent microscopes and SITEview software to provide a flexible, easy-to-operate defect inspection platform for either micro or macro defect wafer inspection.
-
Product
Low Frequency Test Systems
-
Ingenieurbüro Dr. Hillger Ultrasonic-Techniques
Our imaging low-frequency inspection systems are excellently suited to displaying internal defects with high resolution and high dynamics.
-
Product
Sensor Products: Weld Force Gage
90061
-
Model 90061 is a self-contained, portable measurement system which allows auditing of the pinch force generated between the electrodes of resistance spot welders. Resistance welding uses a pair of electrodes to clamp two base metals firmly together prior to and during application of electrical current. Poorly clamped parts result in a defective joint. A correctly clamped assembly aids in reducing the resistance in the joint and allows the current flow to properly heat the base metals to weld the part.
-
Product
Flying Probe Tester
FA1817
-
Flying Probe Tester FA1817, an automatic testing system designed to inspect printed wiring on bare boards. The FA1817’s features and capabilities make it ideal for use in inspecting high-density printed wiring boards. With support for a broad range of test types, from low-resistance measurement to high-insulation-resistance measurement, the system reliably detects the latent defects that trouble end-users.
-
Product
Drone Inspection Software
Qii.AI
-
Qii.AI automates the detection and analysis of defects. It is the only enterprise AI platform that combines drone inspection software with an AI labeling tool, AI-assisted computer vision, and machine learning.
-
Product
Microelectronics And Packaging AOI
-
Machine Vision Products, Inc. has extensive experience in a wide range of Microelectronics and Packaging applications. MVP works with the world’s leading manufacturers on a global basis. From multiple die and wire technologies to leadframe, ball grid array and surface inspection applications, MVP has the widest applications toolbox of any AOI provider. MVP takes pride in the fact that they supply many complex inspection solutions to diverse industries such as Automotive, Telecoms, Medical Devices, Military, and Space. MVP’s 900 Series is the base platform upon which all Microelectronics and Packaging inspection solutions are based. The 900 series 2D capabilities provide metrology and defect detection using a propriety Quad-Color lighting, Telecentric optics and resolutions down to 1um. 3D height measurement capabilities allow for in-line high speed inspection of Dies, paste deposition, positional accuracy, volume and height with a resolution down to 1.13um.
-
Product
Axis Play Tester
LMS 20.0 | VP 425017
-
Maschinenbau Haldenwang GmbH & Co. KG.
The LMS 20.0 axis play tester is used to reliably determine defects and wear on steering parts, wheel bearings, suspension and suspension by means of counter-rotating transverse and longitudinal movement of the test plates. The built-in hydraulic drive ensures a powerful and even movement of the test plates. An automatic mode and other different operating modes make the LMS 20.0 easy to use.
-
Product
DC Safety Inspection Device For Solar Panels
“DC Fault Tester”
-
Identifies defect position instantly- contributes to saving inspection time
-
Product
Inspection System for Die Casting
X-eye 7000BS
-
Appropriate for medium•large size component inspection and detecting surface structure and defects(inside voids and cracks etc).Due to high-energy, high-power Micro-focus X-ray Open Tube, maintenance cost's reduced significantly and enables long-term use with only replacing consumables.Customization is available with selecting main parts by customers depends on their needs for size and material.
-
Product
Partial Discharge Testing Equipment
AR700
-
PD Defect Location in High-Voltage Equipment Insulation by Acoustic Sensors To act on deteriorating insulation the source of PD must be known.The insulation defects produce partial discharges, which emits electrical impulses, radiation of electromagnetic waves as well as acoustic signals.The AR700 measures acoustic signals with multiple sensors spread over the transformer. Then the software determines the failure location using the time difference of all incoming signals. Finally, these coordinates are shown in a 3D model of the transformer. AR700 device is used for measuring of acoustic signals on the external surfaces of gas-insulated breakers and substations, power transformers and other tank high-voltage equipment. The acoustic signals are caused by partial discharges in the insulation, which is the sigh of the defects.The advantage of “AR700” device is the quick installation of the acoustic PD sensors on the external surface of high-voltage equipment tank. The sensors have magnetic holder that is why there is no need to de-energize the equipment for the sensors installation. “AR700” device has 4 syn-chronic channels for acoustic signal measurement. This gives the possibility not only to find the defects in the insulation, but also to locate them. The location function of the “AR700”device is unique for acoustic devices.
-
Product
VisualDetect LCD Voltage Detector / Interface Tester
VDL-01AB
-
Hachmann Innovative Elektronik
VisualDetect LCD is an easily operated voltage detector and interface-tester. Its automatic, thorough self-test ensures reliable function. The permanently enabled interface-tester warns against defect interfaces. Additionally the LC-display indicates the measured current [I/A] and frequency [f/Hz]. Thanks to the integrated configuration menu it can be adjusted to switchgears operated below nominal voltage on-site.
-
Product
Automated Surface Inspection for Glossy Components
-
Flawlessly glossy surfaces are among the most important quality features of many premium products. The smallest surface defects immediately have a degrading effect on the product. The result: disappointed end customers or buyers. At the same time, reflective surfaces are often very sensitive and a challenge for optical metrology. A manual inspection is tedious, expensive, and ultimately always governed by subjective decision criteria. During production, faulty painting or coating processes can cause high scrap rates. Defects that are not detected even during the final inspection can lead to expensive complaints and, in the worst case, to the loss of the customer. Only an efficient, automated surface inspection achieves the highest quality at acceptable costs.
-
Product
Miniature Single Axis Accelerometers
-
Miniature piezoelectric accelerometers are required for applications demanding high frequency range, small size, and low weight. Product testing is necessary in today’s competitive marketplace in order to optimize designs, reduce defects, and improve customer acceptance and satisfaction. Shock and vibration testing offers a structured approach for verifying survivability in environmental influences that may be encountered during service and for precipitating incipient failures so they are not encountered by the end-user. PCB® accelerometers are used extensively for monitoring an object’s response to a programmed vibration input and for controlling the vibration profiles during testing.
-
Product
Electrical Testing
-
Board defects are never an option. Your customer expects perfect boards, each time, every time. Electrical testing is the key in ensuring that the connectivity of a PCB is precisely as specified and that there are no defects or flaws that may cause problems down the line.
-
Product
X-Ray Inspection
-
X-ray inspection systems are used wherever defects need to be detected by non-destructive means. The spectrum of use is broad and ranges from quality controls for complex assemblies, to the testing of materials for cracks and air inclusions, to foreign matter inclusions and shape deviations. The trend toward miniaturization, higher packing densities, and the relocation of components to the interior of the assembly require precise X-ray inspections that detect hidden defects quickly and reliably. X-ray systems from Viscom are used for the inspection of series assemblies as well as sampling and prototype controls. They take care of typical inspection tasks in concealed areas such as void controls, THT filling level measurements, and HIP inspections. At the same time, the systems reliably determine defect features such as coplanarity and polarity – at high inspection speeds and in a cost-effective way.
-
Product
Test Management App
-
Test Management goes mobile with the new Kualitee App. Now, simply use your Kualitee mobile app to manage your testing activities by viewing multiple projects, creating defects, approve or reject test cases and view your Kualitee Dashboard to get the latest status reports on the defects being reported.
-
Product
Ultrasonic Testing
-
Device for detecting defects in finished products, semi-finished products and welded joints, as well as determining their coordinates and using DAC and DGS functios.
-
Product
Ultrasonic Flaw Detector
MFD350B
-
Based on ultrasonic principle, digital ultrasonic flaw detector MFD350B with 320*240 TFT LCD, it can test, orient, evaluate and diagnose various flaws such as crack, lard, air hole in workpiece’s interior swiftly and accurately without any destruction. It can be used in Laboratory as well as in engineering filed. With range of 0-6000mm, it can meet the requirement for general defect inspection in manufacturing industry, metallurgical industry, metal processing industry, chemical industry and so on. Low power design with large capacity and high performance lithium battery module, it can be long standby for months. High quality with low price, it is the first choice for the practical economic model for ultrasonic testing equipment.
-
Product
Leak Testing
-
Leak testing is a non-destructive method to verify the presence of a leak in a component or device.It is implemented as a control methodology for monitoring production process and product quality control. Leak tests are used to find out possible leaks due to non-suitable material (porosity, blowholes, cracks), or in the machining process to find out machining errors or defective parts, and ultimately in assembly, to find out missing or defective gaskets, wrong positioning or assembly. The presence of a leakage could jeopardize the correct functioning of the component, device or its life span, and can also be potentially dangerous for the environment and the safety of its user.
-
Product
3D Automated Optical Inspection
Zenith UHS
-
High-speed full 3D AOI that brings about a revolution in SMT process management Industry-leading speed for full 3D measuring inspection equipment skill solutions- Only solution in the industry to set inspection criteria according to IPC-610 standards- Performs defect diagnosis through measurement-based data and eliminates the causes of possible errors- Powerful 3D solder joint inspection
