Showing results: 1051 - 1065 of 2807 items found.
-
80609010 -
6TL Engineering
The differential active probe helps to carry weak HF signals far away with the minimum disturbance of the original source. The module accepts discrete wiring or direct spring loaded test probe solder. In any case, the input signal wires might be as short as possible.
-
TBCP1-200 -
TekBox Singapore Pte. Ltd.
The TBCP1-200 is a fixed aperture RF current monitoring probe.The probe has a 3dB bandwidth of approximately 200 MHz. The aperture of the RF current monitoring probe is 25 mm. Its transfer impedance is > 14 dB Ohm in the range from 40 kHz to 200 MHz.
-
80609000 -
6TL Engineering
The single ended active probe helps to carry weak HF signals far away with the minimum disturbance of the original source. The module accepts discrete wiring or direct spring loaded test probe solder. In any case, the input signal wires might be as short as possible.
-
80609007 -
6TL Engineering
The single ended active probe helps to carry weak HF signals far away with the minimum disturbance of the original source. The module accepts discrete wiring or direct spring loaded test probe solder. In any case, the input signal wires might be as short as possible.
-
-
Extech 881603 -
Extech Instruments Corporation
The Extech 881603 is a Type-K Immersion Probe. It is for use with any meter that has a Type-K connector.
-
WP400-3 -
Wavecontrol, S.L.
Wavecontrol presents a new and unique field probe for the measurement of electric and magnetic fields that integrates both E & H sensors within dimensions of only 3 cm². Which makes it unique is that Wavecontrol has managed to add an E field sensor in a basic structure of a classical 3 cm² field probe. It has been possible, therefore, to obtain a 3 cm² field probe without compromising the capability of assessing E and H fields of its 100 cm² big sister, the recognized and successful WP400.
-
Fairview Microwave Inc.
Fairview Microwave’s semi-rigid test probe assemblies come in multiple cable diameters to help when attaching the unterminated end of the probe to a circuit board trace. There are two versions including straight-cut probe ends for those that would like to customize the dimensions of the center conductor and dielectric dimensions, as well as pre-stripped probe ends that are ready for immediate use. By soldering the outer conductor to the signal ground and the exposed center conductor to the trace carrying the signal of interest, simple sampling measurements can be made without having to create a separate subassembly circuit board or add a connector to the circuit layout which can take up valuable real estate. Fairview provides 3 diameters of semi-rigid coax and 3 different lengths from 3 inches to 12 inches to fit a variety of trace widths and applications. All test probes are 100% RF tested to ensure the cable assemblies operate to 6 GHz and also to make sure that the SMA connector interface meets the 1.35:1 VSWR specification prior to shipping. To protect the small diameter coax from damage, each part is shipped in a clear protective tube that can also be used for storing the probes for future use.
-
Hatteras -
Del Mar Photonics, Inc.
The Hatteras is first professional system on the market for ultra fast transient absorption pump - probe spectroscopy. Two linear image sensors (multichannel detection) or two photodiodes (singlechannel detection) are placed behind an imaging spectrometer to measure probe and reference pulses, originating from a femtosecond white light (continuum) generator or from an optical parametric amplifier.
-
Si-RV3 -
Sauermann Group
Sauermann's vacuum probe supports the quick, safe evacuation of refrigeration systems and heat pumps with highly accurate measurements.
-
-
CE Series -
Japan Electronic Materials Corp.
*Standard Cantilever Probe Card*Low Contact force*Stable Contact*High accuracy of alignment*Suitable for variety of Devices
-
15KVPSet -
Summit Technology, Inc.
Our 15KVPSet is a set of three voltage probes that allow direct connections up to 15,000 Vrms (15KV) 3 phase power.
-
Elcometer 355 -
Elcometer Limited
Unique probe modules allow the Elcometer 355 Coating Thickness Gauge to be versatile and flexible for any coating thickness measurement application.
-