Showing results: 2041 - 2055 of 2555 items found.
-
Megger Group Ltd.
Transformer insulation resistance deterioration is one of the most common causes of transformer failure: a failing transformer is a costly replacement in an electrical system with the potential for a long downtime. If you fail to maintain your transformer with regular insulation resistance testing (as can be carried out by the Megger Transformer Ohmmeter (MTO) series of transformer test equipment) then it’s likely to fail before reaching its maximum operating life.
-
EPM 9450 -
GE Digital Energy
The EPM 9450 is the entry point for GE's premium 9000 meter series with advanced power quality capability. The unit utilizes ACCU-Measure Technology to provide highly accurate revenue grade readings coupled with advanced data analysis. The unit measures over 15,000 electrical parameters including real time harmonics to the 127th order, voltage surges and sags and a large assortment of advanced monitoring functionality.
-
National Technical Systems
According to the best meteorological estimates, the surface of the earth is struck by lightning approximately 100 times each second, which averages out to about 8 million strikes per day. In addition, the Federal Aviation Administration reports that the average commercial aircraft gets hit by lightning on average about once for every 1,000 hours of flight it completes, which amounts to approximately once a year.With statistics like these, it’s obvious that providing adequate lightning protection to electrical components is crucial — whether that’s onboard an aircraft or as part of a ground-based facility. Fortunately, at NTS, we’ve been helping companies do just that for well over 50 years. Thanks to our lightning simulation and modeling services, companies are able to develop high-quality products that meet with their respective compliance regulations — from military and defense to Airbus and Boeing published standards.
-
IIB-3910-CPCI -
Western Avionics Ltd.
The IIB-3910-CPCI is a single slot intelligent interface card providing complete STANAG 3838 and STANAG 3910 test, simulation and bus analysis capability for the CompactPCI Bus. The IIB-3910-CPCI supports concurrent Bus Controller (BC) and up to 31 Remote Terminals (RT) with Bus Monitor (BM). An additional stand-alone Chronological Bus Monitor (CBM) facility is also provided, with powerful multi-level triggering capability. Full error injection capability in both 3838 and 3910 modes is provided in BC and RTs modes, with full error detection in BC, RT, BM and CBM modes. Dual redundant 3838 interface, with user selectable dual redundant optical or single redundant electrical 3910 interface are featured. 2 Mbytes of dual ported RAM are provided. The board is supplied with C drivers in source code and Windows menu driven software as standard.
-
Shenzhen Everbest Machinery Industry Co.,Ltd.
Visible light digital camera640x480 resolution with flash provides sharp images regardless of lighting conditionsPicture-in-pictureDisplays thermal image super-imposed over a digital imageLED flashlightAllows the visual camera and fusion to be used in poorly lit environmentsWide temperature range: -20 to 400°C targeting electrical and industrial applications±2% accuracy reliable temperature measurementThumbnail view: easy to view and analyze images quicklyThe image rotationThe ability to automatically rotate the active imageAudio recorded with the video imageA speaker to listen to audio recorded with the video imageCapacitive touchscreenMore easy, productive and effective to operate itLi-ion rechargeable batteryLasts >4hrs continuous use, replaceableCopy to USBEasy uploads images from camera to USB memory cardArea (minimum/maximum) modeShows the minimum or the maximumTemperature reading in the selected areaInside Memory 100M bytesData and Live video transform between camera and PC or smartphone
-
CZ20050 -
Aegis Pty. Ltd.
Telecommunications, Electrical, Data, and Video installers should all have a TDR in their toolkit. From measuring the length remaining on a drum to knowing exactly where to dig to find that cable fault the Cable Gauge can be invaluable. Opens, Shorts, and length are all measured by the metre letting you know how much you have or where the issue is. Stocktaking of cables is made simple using the Cable Gauge. Using TDR technology, the Cable Gauge diagnoses cable faults with no launch or dead zone at an accuracy of ±2%. Simply select the appropriate cable type from the pre-stored library or enter the cable NVP, attach the leads to two conductors of the cable and with a single press of a button the length of the cable or distance to an open or short is displayed. Voltage on the wires up to 250v is continuously measured by the built in, true RMS voltmeter and is displayed to warn of a potentially unsafe condition.
-
CZKS-6 -
Lisun Electronics Inc.
It is designed according to terms and conditions of IEC60884-1, IEC60669-1, GB2099.1-2008 and GB16915.1-2003, for life test of plug and socket and switch products of household and similar use appliances. The device can connect with matched load cabinet, in order to conduct a test of electrical life, normal operation and breaking capacity. The equipment provide some clamp, it can test plug and socket production, wall switch, rocker switch, dial plate switch and button switch.
-
VVLA-30M -
Lisun Electronics Inc.
The three loop antenna VVLA-30M is a standard measurement antenna according to CISPR15-2005/GB17743-2007 standard , it can work with LISUN EMI-9KA / EMI- 9KB EMI Receiver System for EUT magnetic field radiation measurement between X, Y and Z planes. The antenna measurement is accurate, switch conveniently and it can completely replace imported products.
-
ModuLab XM MTS -
Ametek Scientific Instruments
I-V (voltage scans with current measurement - used to characterize electronic and dielectric materials)P-E (polarization / electric field - used to run hysteresis tests to characterize ferroelectric materials) High-speed pulse (used to activate charge carriers in electronic and dielectric materials)Staircase and smooth stepless analog ramp waveformsImpedance, admittance, permittivity / capacitance, electrical modulusC-V capacitance - voltage, Mott-SchottkyAutomatic sequencing of time domain and impedance/capacitance measurements
-
G5.CT -
Regatron AG
The G5.CT series are unidirectional regenerative sinks. It was developed specifically for testing chargers and is suitable for use in laboratories and on test benches. The modular and finely graded G5.CT series is characterized by highly dynamic response times and a wide current-voltage range with an auto-ranging factor 3. The G5.CT series can simulate the electrical charging characteristics of a modern battery pack. This includes active voltage output and Ri realtime simulation.
-
Becker & Hickl GmbH
Designed and manufactured by Becker & Hickl – bh delivers prominent picosecond diode lasers with wavelengths from the NUV to the NIR. All bh pulsed diode lasers work with simple +12V power supply or pull their power from the USB port of a PC or Notebook Computer. Other features are high repetition rate, short pulse width, unprecedented timing and power stability, and extremely low electrical noise level.
-
Autolink AL539 -
Autel
The AutoLink® AL539 OBDII & Electrical Test Tool supports all 10 modes of OBD II test for a complete diagnosis. Featuring the unique patented One-Click I/M Readiness Key, circuit test, starting and charging systems test, TFT color display, and built-in speaker, the versatile, easy-to-use AL539 will streamline automotive service and help ensure rapid, accurate diagnosis and timely repair.
-
AC-220 -
Com-Power Corporation
The AC-220 Combilog antenna is for EMC emission and immunity up to 2 GHz.. It combines the electrical properties of two antenna (biconical and Log ). It reduces overall testing time by 20 - 30% due to antenna switching. It is Optimized for emission measurements, but can handle up to 500 Watt CW, making it suitable for most immunity measurements . Each antenna is individually calibrated at 10 meters and the data included the purchase price.
-
IT7300 Series -
I-TECH Electronic Co., Ltd
In order to meet the bigger range of AC power supply and more complex change characteristics, engineers need more powerful and stable AC power supply to simulate the actual working environment. IT7300 series is the best solution in this area. IT7300 series can be widely applied in the electronics and electrical industry, lighting, aviation, military, specification verification of RD, the use of laboratory testing and factory production online test etc.
-
DM393 -
UEi Test & Measurement Instruments
The DM393 is one of our safest Industrial Duty meters ever made. All inputs, ranges and functions protected to CATIII 1000 Volts. Perfect for HVAC and electrical technicians whose applications require higher accuracy measurements and True RMS precision. Built-in temperature means one less instrument to bring to the job. The DM393 has convenient access to battery and fuses without breaking calibration seals
