Showing results: 2311 - 2325 of 2551 items found.
-
Extech 480172 -
Extech Instruments Corporation
This Extech 480172 Line Splitter provides a fast and easy way to “open” standard 120 Volt AC electrical lines, eliminating the need to cut off the plug and separate the conductors. When connected between a 120 Volt AC outlet and a device under test, this splitter separates the hot/live conductor from the neutral and ground, which enables users to measure AC current up to 15 Amp on a two-wire or three-wire lines using a clamp meter. This splitter also features two Voltage Test jacks so that voltage can be measured using a multimeter.
-
A1 / C1 / C2 -
Becker & Hickl GmbH
*bh FLIM Embedded in Nikon NIS-Elements Software*Two Fully Parallel TCSPC FLIM Channels*Compact bh Simple-Tau or Power-Tau System*Two HPM-100-40 GaAsP Hybrid Detectors*Excitation by bh ps Diode Lasers*Excellent Time Resolution: Electrical IRF Width 6.5 ps FWHM*Excellent Timing Stability*Time Channel Width Down to 813 fs*Megapixel FLIM, Up to 2048 x 2048 Pixels at 256 Time Channels*Detection Wavelength Range from 360 nm to 700 nm
-
42-872A-102 -
Pickering Interfaces Ltd.
The 40-872A-102 (PXI) and 42-872A-102 (PXIe) are 50 Ohm 4 to 1 PXI RF multiplexers with 2 banks in a single slot. They have low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. Each MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz with each path having a nominally equal insertion loss. The injection of noise and unwanted signals into the signal paths of this RF MUX has been minimized by careful attention to the mechanical and electrical design.
-
ACMAS Technologies Pvt. Ltd.
WEIBER designs and manufactures standard as well as customized water spray test chamber for evaluating various automotive, electrical and electronics items under water, rain or shower conditions. The chamber interrogates the performance of parts when subjected to water droplets.The system is based on the IP X5, X6 specification requirements, and can also accomplish individual automaker’s tests, as well as electrical-enclosure tests.Our system uses multiple control solenoids to vary the water's spray volume/pressure. A holding tank prepares the water to the desired temperature, if required. A pump ensures the water is delivered in the proper pressure range.
-
Model FT1 -
Gopal Electronics
The Franklin tester FT‐1 is designed to measure the surface insulation resistivity of electrical steel sheet according to the ASTM Standard A717 and IS:649. This test method is suitable for quality control in the application of insulation coating. For ease of testing FT‐1 automatically set 300 PSI pressure on the sample by the inbuilt hydraulic unit and it is capable to set the desired test temperature of the platform. Then the regulated supply of 0.5V gets on and the current flowing through the insulation get measured. The calculated insulation resistivity will be displayed on graphics LCD display and as well as on printed report via thermal printer.
-
WT2000A-CCFL -
Lisun Electronics Inc.
This tester is specially designed for analyzing the electrical characteristics of CCFL Electronic Ballast, meets the test requirements in international standard• Input characteristics analysis: measure Vrms, Irms, W, PF, Hz, phase angle Measure THD, 0 to 39th harmonic components, Accuracy: ±(0.4% reading+0.1% range+1 digit)• Output characteristics analysis: measure lamp voltage, lamp current, lamp power, oscillatory frequency, crest factor of lamp current, Accuracy: Class 2• Interface RS-232C provided for easier communication with PC for printing test report
-
36330 -
S & G Tool Aid Corp
Use to test electronic fuel injection signals, idle air control circuit and spark plug circuits. Quickly diagnose "no start" and engine miss conditions in the electrical fuel injection and spark plug circuits. Analyze rough running engines. Includes 8 Noid Lights (for checking GM PFI, FORD TBI, GEO TBI, BOSCH PFI, GM TBI, GM SCPI, BOSCH 2 and GM Multec 2; 2 IAC Test Lights (for straight and 90 applications); and Cat. No. 23900, In-line Ignition Spark Checker.
-
Keysight Technologies
Equivalent-time (sampling) oscilloscopes are also known as digital communication analyzers (DCA). They are designed to visualize and analyze the analog properties of high-speed signals used in data center and wireline telecom applications. The Keysight DCA platform features a wide variety of optical, electrical, and TDR/TDT modules, compliance applications, and a common FlexDCA user interface to ensure more efficient testing in both R&D and manufacturing. Due to an ultra-low jitter and low-noise acquisition system, the Keysight DCA series provides industry-leading measurement accuracy for high-speed digital designs including 400G/800G Ethernet and Fibre Channel.
-
LSP-500VAC -
Lisun Electronics Inc.
• Applied with the AC-DC-AC inverter technology and digital waveform synthesis & waveform feedback technology, low distortion power; • Applied with entire cycle high-precision measurement technology and high-speed sampling technologies, panel of instrument will directly and accurately displays the power output of the voltage, frequency, current, active power and power factor to achieve the integration of the source table; • Applied with SCM control and measurement technology, high intelligence; • Applied with zero output impedance technology, the output equivalent impedance is almost zero and further improve the stability of power supply; • Applied with isolated floating output technology, the power output and input have good isolation, floating output, conducive to make sure power itself safety and operator’s safety; • Perfect voltage, current anomalies and overheating protection, improve the reliability of power supply; • Applied with power limiting technology to avoid strong interference on the power grid and other electrical equipment, while facilitating reliable operation of the power supply itself; • The input voltage can be option via a toggle switch of panel mains 110V/220V; • The initial phase and end phase of the output voltage waveform can be set {0°-359° (±1°)}; • Measurement process can be programmed to control (1 to 50 memory groups, 1 to 9 steps for each memory group);
-
Premier Electrosystems
Premier Electrosystem's Insulation Resistance test (also known as Megger, Mega Ohm Meter, Million Mega Ohm Meter) indicates whether any corrective maintenance or replacement of installed equipment is necessary, to assess if the newly installed equipment can be safely energized, and to trend the gradual deterioration of the equipment over its service life. Insulation Resistance Test is carried out to ensure the healthiness of overall insulation system of electrical equipment. It reflects the presence or absence of harmful contamination, dirt, moisture and gross degradation. Common areas of application are testing of appliances, wires, transformers, harnesses, motors, etc.
-
Ansys Corporation
Ansys electromagnetic field simulation helps you design innovative electrical and electronic products faster and more cost-effectively. In today’s world of high performance electronics and advanced electrification systems, the effects of electromagnetic fields on circuits and systems cannot be ignored. Ansys software can uniquely simulate electromagnetic performance across component, circuit and system design, and can evaluate temperature, vibration and other critical mechanical effects. This unmatched electromagnetic-centric design flow helps you achieve first-pass system design success for advanced communication systems, high-speed electronic devices, electromechanical components and power electronics systems.
-
YWX/Q-010X -
Lisun Electronics Inc.
Composite Salt Spray Test Chamber stimulate the actual natural conditions to do accelerated corrosion test, all the testing are based on common states on the natural environmental: such as combine with salt spray, hot air drying, humidity, low temperature and so on. The test samples are widely used on the intense changes in the environment, like automobile parts, aviation equipment, building materials, coating, electric and electrical machinery so on. YWX/Q-150X series is full compliance with ASTM D4728I, EC 60068-2-1, IEC 60068-2-14 and EIA/JEDEC JESD22-110-B standard requirements etc.
-
Electromechanica, Inc.
The rail inverter test system uses a pulse test methodology to verify proper operation of the IGBT switching elements in a subway car motor control. The system is designed to verify proper commutation of the switching elements. A large capacitor bank allows testing at DC voltages up to 1kV and peak currents of up to 3kA into reactive loads.The system also integrates self test capabilities and safe-to-turn-on (STTO) diagnostics to ensure no gross faults are present prior to the application of high voltages. Further the system includes dielectric withstand (hi-pot) test capability to ensure electrical safety.
-
Shanghai Morningtest Environmental Chambers Co.,Ltd.
Humidity chambers offer a wide range of standard solutions for your testing program. Environmental testing with a humidity chamber helps improve product reliability and durability. Humidity chambers are available in a variety of styles, sizes, and performance configurations. All humidity chambers come with a standard temperature range for combined temperature and humidity testing.Humidity may affect the life expectancy of a component by creating stresses on the part materials and altering its electrical properties in a way that the component reliability is significantly diminished.Humidity tests are those performed with the aim of evaluating the properties of materials used in components and the reliability of non-hermetic packaged devices in humid environments.
-
Accsense, Inc
Accsense Electrocorder dataloggers are electrical logging devices monitoring power/energy, current/voltage, power quality and more. These products perform ongoing datalogging to identify issues with supply and equipment; to calculate and prove the value of future energy savings; and as low-cost investments for long-term energy savings. Electrocorder constantly samples every cycle multiple times (recording the Min, Max and Average) over the set period. Additionally, specialized Electrosoft software is included FREE with every unit to assist with data interpretation, enabling users to define the voltage to plot power and energy, then simply upload their recorded data via USB to a PC for analysis.
