References
A source of comparison.
See Also: Reference Standards, Reference Antennas, Reference Decoders, Reference Jumpers, Reference Sources, Reference Transformers, Reference Transmitters, Acoustical References, Frequency References, Solar Reference Cells
-
Product
Crimp Force Monitor
638007950
-
The crimp force monitor measures the force signature of a crimped terminal and compares it to a reference crimp. Depending on the limits programmed, the measurement will pass, fail, or be suspect.
-
Product
Weather Radar Receiver
-
This is an example of a custom four-channel C-Band Receiver uses a single conversion technique to translate incoming 5.56 GHz radar signals to a 60 MHz IF. The Receiver is divided into two polarization sections, each with a dedicated channel for the received signal and a second channel for a reference signal originatingfrom the transmitter. There are two identical circuits in the Receiver, one reserved for vertically polarized signals, and the second for horizontal signals.
-
Product
Frequency Synthesizers
-
A frequency synthesizer allows the designer to generate a variety of output frequencies as multiples of a single reference frequency. The main application is in generating local oscillator (LO) signals for the up- and down-conversion of RF signals.
-
Product
4-Channel 200 MHz A/D with 32-Channel DDC, Virtex-7 FPGA - XMC
Model 71762
-
- Complete radar and software radio interface solution- Supports Xilinx Virtex-7 VXT FPGAs- Four 200 MHz 16-bit A/Ds- Four multiband DDCs- 4 GB of DDR3 SDRAM- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multimodule synchronization- PCI Express (Gen. 1, 2 & 3) interface up to x8- VITA 42.0 XMC compatible with switched fabric interfaces- Optional user-configurable serial gigabit interfaces- Optional LVDS connections to the Virtex-7 FPGA for custom I/O- Also available in 3U VPX, 3U & 6U cPCI & PCIe- Supports GateXpress® FPGA-PCIe Configuration Manager- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe- See comparable Jade Xilinx Kintex UltraScale FPGA Module: Model 71862
-
Product
68-Pin VHDCI Male to 68-Pin D-SUB Female, Shielded Multifunction Cable
189588-02
Multifunction Cable
The SHC68M-68F-RMIO Cable, sometimes referred to as SHC68-68-RMIO, connects to the terminal block of a multifunction reconfigurable I/O (RIO) device. The SHC68M-68F-RMIO Cable is available in different lengths.
-
Product
Carrier Boards
ROM-DB7501
Carrier Board
ROM-DB7501 is an Referenced Carrier Board designed for Advantech's RISC Qseven 2.0 module. It i provides a thorough environment for module board evaluation with its completefunction support. It also supports 12V power input through AC/DC power adapter and with smart battery design, it's more easier for the end user to design portable devices by referring ROM-DB7501 design.
-
Product
SR Series AC Reference Supplies
-
Computer Conversions Corporation
The SR Series are miniature, low cost AC reference generators designed to supply 26 or 115 Volt excitation to Synchros or resolvers in military and industrial control applications. They accept +/- 15V DC and provide up to 5VA of transformer isolated output power. These converters are packaged in PC card mounting modules 2.6" x 3.1" x 1"H.
-
Product
4-Ch 500 MHz A/D with DDC & 4-Ch 800 MHz D/A with DUC, Virtex-6 FPGA - 6U VPX
Model 58651
-
- Complete radar and software radio interface solution- Supports Xilinx Virtex-6 LXT and SXT FPGAs- Four 500 MHz 12-bit A/Ds- Four multiband DDCs (digital downconverters)- Two DUCs (digital upconverters)- Four 800 MHz 16-bit D/As- Two multiboard programmable beamformers- Up to 4 GB of DDR3 SDRAM; or: 64 MB of QDRII+ SRAM- PCI Express (Gen. 1 & 2) interface up to x8- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multiboard synchronization- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- Ruggedized and conduction-cooled versions available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
1211a Optical Receiver/Distribution
-
Precise Time and Frequency, Inc.
To complement the range of high quality frequency and timing references, Precise Time and Frequency, LLC. has now introduced a new Optical Time Code Receiver, with Auto Switching, a full complement of time code outputs, and Ethernet/RS232 remote monitoring/control interface.In addition to the auto switching capability, the new ptf 1211A delivers up to thirty six channels of Time Code outputs, including re-transmission of the optical input. The unit can accept a pair of inputs (usually from separate primary and backup sources), and provides monitoring of both the inputs and outputs for signal integrity.If the primary input fails, the unit will automatically switch to the backup input and indicate a primary signal fault.Full remote monitoring and control via RS232 and Ethernet interfaces includes telnet, http (web browser), and SNMP protocols.
-
Product
Network Element Management System
VCH-901
-
The control system (CS) VCH-901 is designed to control and monitor network elements (NE) that act as sources of clock signals on a digital communication network. These SCs include primary reference oscillators (PEG) VCH-001, secondary master oscillators (VZG) VCH-002 (Time-H), SSU55400А (HP), SSU2000E (Simetricom), SSU5548В and SSU5548С (Oscilloquartz), local master oscillator ( MZG) M100 (LONIIS), synchronization signal distribution equipment ARSS (ALTO).
-
Product
Series Precision Multi-Ratio Current Transformers
PMT25090
-
Power Measurement Technologies Inc.
Precision two-stage toroidal current transformers find application as the reference in determining the accuracy of instrumentation current transformers.
-
Product
LTE/LTE-Advanced Multi-Channel, Reference Solution
-
Gain greater insight faster with a compact, multi-channel LTE-A PXI signal generator and signal analyzer reference solution.This Reference Solution uses world-class Signal Studio software to create complex LTE-A waveforms and the 89600 VSA/WLA software to connect to multiple analyzers. The VSA software allows engineers to quickly view multiple antenna elements simultaneously and analyze the RF performance and modulation domains for timing and signal quality issues in complex carrier aggregation and MIMO/beamforming designs.
-
Product
Reference Meter
ST1000
-
Shenzhen Star Instrument Co., Ltd.
The ST1000 three-phase reference meter incorporates high-precision A/D converter, DSP, wide-range measuring and embedding industrial PC technologies. It has a high accuracy of class 0.01. The voltage measuring range (phase voltage): 1V~480V, current measuring range: 1mA~120A.
-
Product
Mass Spectrometry Solutions
-
Discover new ways to apply mass spectrometry to today’s most pressing analytical challenges. Innovations such as Trapped Ion Mobility (TIMS), 10kHz scanning lasers for MALDI-MS Imaging that deliver true pixel fidelity (10 um spatial resolution), and eXtreme Resolution FTMS (XR) technology capable to reveal Isotopic Fine Structure (IFS) signatures are pushing scientific exploration to new heights. Our mass spectrometry solutions enable scientists to make breakthrough discoveries and gain deeper insights.Our industry leading software solutions such as SCiLs Lab for MS Imaging, FDA cleared microorganism reference library for the MALDI Biotyper, Biopharma Compass 2.0, and Toxtyper are examples our solutions doing the work for you. Bruker's product lines include the following technologies: FTMS, rapifleX MALDI-TOF/TOF, MALDI Biotyper Systems, timsTOF UHR-QTOF, Toxtyper, Triple Quadrupole, HDX Solution, ToxScreener, PesticideScreener
-
Product
Dual Channel High Voltage Linear Amplifier
F10AD
-
his unit contains two independent F10A amplifiers that share common ground reference and power supply.
-
Product
Thermal Test Chip
-
Thermal Engineering Associates, Inc.
Thermal Test Chips (TTC) are used in many different Applications: Package Thermal Characterization, Heat Source Simulator, Temperature Reference Platform, Transient Analysis, System Thermal Management Design, Thermal Interface Material (TIM) Measurement & Characterization, Heat Sink Measurement & Characterization.
-
Product
9-Pin DB-9 Female to 9-Pin DB-9 Female Serial Cable
183283-04
Serial Cable
The 9F-9F Serial Cable, sometimes referred to as GPIB Serial Cable, connects and controls GPIB devices using RS232 and RS485 serial ports. The 9F-9F Serial Cable is offered in different lengths.
-
Product
PXIe Arbitrary Waveform Generator, 500 MSa/s, 16 bit, 200 MHz
M3201A
Waveform Generator
The M3201A PXIe arbitrary waveform generator is ideal for general purpose AWG automated test requirements. It offers high channel density with high-quality output with low phase noise. The optional real-time sequencing, intermodulation synchronization, and graphical FPGA programming software tools expand its capability to enable a number of solutions including envelope tracking (ET) and DPD (part of PA/FEM reference solution), MIMO, baseband electronics design, wireless device manufacturing, ATE, beamforming and other multi-channel coherent signal generation and multi-channel signal generation.
-
Product
Tester Electrical Interfaces
-
The primary element of the tester electrical interface is the Probe Pin Ring (PPR). Sometimes referred to as a ‘tower,’ this array of spring-loaded probes can be arranged to provide a controlled impedance path, a low leakage connection, a low inductance arrangement for high currents, or just about any connection characteristic you require. inTEST EMS provides electrical interfaces in various OEM-supported designs, inTEST standards, and custom configurations.
-
Product
34-Pin RTSI Female to 34-Pin RTSI Female Ribbon Cable
776249-03
BUS Cable
The RTSI Cable, sometimes referred to as RTSI, connects RTSI bus connectors on adjacent NI plug-in boards. The RTSI Cable is offered with different numbers of ribbon connections and in different lengths.
-
Product
Environmental Test Chamber
-
Shenzhen Bonad Instrument Co., Ltd.
Climatic Test Chambers are also referred to as environmental test chambers, which are the general name of various test equipment used to simulate the natural environments of raining, high temperature, low temperature, dewing, salt mist, illumination, dusting, etc. There are kinds of testers including constant temperature chamber, constant humidity chamber, ozone aging test chamber, UV accelerated weathering tester, vacuum hot air oven, salt spray chamber, steam aging tester, rain test chamber, dustproof test chamber, ventilation aging chamber, xenon lamp weathering test chamber and so on. BONAD provides various environmental test chambers. You are welcome to contact us. BONAD will provide you with professional technical consultation and high-quality testing equipment.
-
Product
Pulse Pattern Generator, 3.35 GHz, single channel
81133A
Pulse Generator
The Keysight 81133A single-channel 3.35 GHz Pulse Pattern Generator is the latest product in the long history of Keysights high-speed Pulse Pattern Generators. When timing and performance requirements are critical, for example in high-speed serial bus applications like PCI Express or Serial ATA, its fast rise times and low intrinsic jitter allow the precise and in-depth characterization of devices, e.g. receivers or backplanes. Like its predecessor, the Keysight 8133A, the new 81133A sets the standard for high-speed applications. The Keysight 81133A lets you test your DUT instead of the pulse or data source! For applications that require multiple output channels or multi-level signaling like pre- and de-emphasis (PCI Express) or squelch (Serial ATA), please refer to the 81134A.
-
Product
Current Transformers Test Set
-
Supreme Instrument Laboratories
The basic unit is sensitive magnetic comparator and also it incorporates electronic null detector to facilitate the balance. The reference Current 5A. or IA. obtained from Standard Current Transformer and in comparison to that the vector length and phase displacement is measured. The ratio error in percentage and phase displacement in minutes are directly compared and indicated on dials.
-
Product
Timing Modules
-
Quartzlock provides Timing Modules for network timing, reference disciplining to various input references such as 1PPS, GPS receiver and Frequency References.
-
Product
Hydrophone
RESON TC 4040
-
The TC4040 is an ideal standard reference hydrophone for calibration of transducers, hydrophones and underwater acoustic measurement systems.The TC4040 offers flat frequency receiving response over a wide frequency range and the relatively high transmitting sensitivity makes it very useful within many areas of underwater acoustic research, tests and measurements.
-
Product
Timing And Sync
-
Precision timing is critical for defense and commercial industries and powering essential network operations. Safran offers secure time servers and solutions for accurate network synchronization, ensuring security, compliance, and adherence to best practices. Safran excels in delivering precision timing solutions, including NTPNTP, or Network Time Protocol, is a widely used networking protocol that enables computers and devices to synchronize their system clocks with a reference time source. It ensures accurate timekeeping in computer networks by allowing devices to obtain precise time information from NTP servers, which are typically synchronized to highly accurate atomic clocks. NTP is essential for various applications and services that rely on synchronized time, such as network security, authentication, and data logging. time server appliances and GPSGlobal Positioning System is a navigation satellite system. See also master clocks globally.
-
Product
Cable Assembly, 200-Pin LFH, Male Bottom Exit (Male Screwlocks) to 4x50-Pin D-type, Female, 0.5m
A200LMB-04F050D5B050
Cable Assembly
This 200-pin male to 50-pin D-type female 0.5m long cable assembly is suited for direct connection to all Pickering Interfaces products using the 200-Pin LFH connector and is constructed from 4 bundles of 50-wire flat/round ribbon cable. The connector assembly can be secured to the product by screwlocks. This cable assembly can be used with Pickering 50-Pin D-Type connector blocks (refer to 90-005D).
-
Product
Optical Receiver Stress Test Solution
N4917B
-
The N4917B software provides an automated standard compliant stressed receiver sensitivity test according to 100GBASE-LR4, ER4 and SR4 test specification. In order to do this kind of test, several test instruments such as a bit error ratio tester, digital sampling oscilloscope, optical reference transmitter and tunable laser source are required to operate together to achieve a compliant, repeatable optical stressed eye. This stressed eye is then fed to the receiver under test, where bit error ratio is measured under the stress conditions as defined in the standard.
-
Product
Solution Standard Reference Materials
-
NCS Testing Technology Co., Ltd.
Solution Standard Reference Materials by NCS
-
Product
1 GHz A/D and D/A with Virtex-6 FPGA - 3U VPX
Model 52630
-
- Complete radar and software radio interface solution- Supports Xilinx Virtex-6 LXT and SXT FPGAs- Supports gigabit serial fabrics including PCI Express, Serial RapidIO and Xilinx Aurora- One GHz 12-bit A/D- One GHz 16-bit D/A- Up to 2 GB of DDR3 SDRAM or 32 MB of QDRII+ SRAM- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multiboard synchronization- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- 3U VPX form factors provides a compact, rugged platform- Compatible with several VITA standards including: VITA-46, VITA-48 AND VITA-65 (OpenVPX™ System Specification)- Ruggedized and conduction-cooled versions available- Synchronize up to twelve modules with Model 9192 System Synchronization and Distribution Amplifier- 1U Rack-mount
