References
A source of comparison.
See Also: Reference Standards, Reference Antennas, Reference Decoders, Reference Jumpers, Reference Sources, Reference Transformers, Reference Transmitters, Acoustical References, Frequency References, Solar Reference Cells
-
Product
C Series Relay Output Module
Input/Output Module
The C Series Relay Output Module enables you to switch up to eight signals at 60 V maximum DC switching voltage and up to 250 V of maximum AC switching current. For quick reference, every channel features an LED to indicate the state of that channel. The C Series Relay Output Module allows for direct connection to a wide array of industrial devices such as motors, actuators, and DC devices.The C Series Relay Output Module includes the NI-DAQmx driver and configuration utility that simplify configuration and measurements. NI-DAQmx supports NI programming environments as well as Python, ANSI C, C#.NET, and MathWorks MATLAB® software.
-
Product
9-Pin DB-9 Female to 9-Pin DB-9 Female Serial Cable
182238-04
Serial Cable
The 9F-9F Serial Cable, sometimes referred to as GPIB Serial Cable, connects and controls GPIB devices using RS232 and RS485 serial ports. The 9F-9F Serial Cable is offered in different lengths.
-
Product
Crossed-Roller Bearing Linear Stage 13mm Travel XYZ,Sensitivity 2um
AKSM13(A)-40
-
Model:AKSM13(A)-40 Crossed-Roller Bearing Linear Stage 13mm Travel XYZ,Sensitivity 2umDetails&Spec: Please refer to KSM13(A)-40 Specification,It is combinated by2pcs KSM13(A)-40 (C,SR,SL) and 1pc KSM13(A)-40CZ(as vertical stage)
-
Product
Reference Meter
SB1300
-
Shenzhen Star Instrument Co., Ltd.
The SB1300 three-phase multi-function reference meter incorporates 32-bit floating point DSP, wide-range measuring and embedding industrial PC technologies. This model was the first approved by China National Institute of Metrology. Star Instrument has been granted the first manufacturing license for class 0.02 reference meters. Basic measuring range (phase voltage): 1V~480V, current measuring range: 1mA~120A; wide measuring range (phase voltage): 0.1V~1000V, current measuring range: 0.1mA~200A
-
Product
Acoustical Generator (STIPA Reference)
TalkBox
-
The TalkBox is an acoustic signal generator for speech intelligibility measurements in evacuation and announcement systems, as well as for level alignment of teleconference or other audio systems. It allows you to perform a complete end-to-end evaluation of the speech intelligibility STI from the talker’s microphone to the listener’s ears.
-
Product
Rectangular Horn Antennas
-
SAGE Millimeter wave rectangular gain horns, also called pyramidal gain horns, are offered as both standard and custom models with a rectangular waveguide interface. The pyramidal gain horns only support linear polarization. With a calibrated gain chart, these horns can be used to measure the gain of other antennas by comparing the generated signal levels of both. For this reason, these horns are also referred to as standard gain horns. The listed models offer 23 dB nominal gain, 10/11 degrees typical half power beamwidth and 14 dB/30 dB typical side lobe levels at the center frequency of the band. These horns cover full waveguide bandwidths within the frequency range of 8.2 to 170 GHz. In addition to the models listed below, models with 10, 15, 20 and 25 dB gain and other frequency bands are also available.
-
Product
FMC Loopback Test Board
-
The FMC loopback tester board enables developers and assembly factories to test and characterize the FMC carrier board interfaces. The board features full differential loopbacks on all the FMC high pin count (HPC) connector interfaces including LA, HA, HB, DP and CLK. It also provides a 125MHz transceiver LVDS reference clocks on GBTCLK signals. The FMC loopback board is based on VITA 57 standard with ruggedized conduction or air cooling.
-
Product
Low Noise Differential Preamplifiers
-
Provide a high gain amplification to 1MHz with an AC output derived from a very low noise FET instrumentation amplifier. Each model has fixed gain settings of x1 (0dB), x10 (20dB), x100 (40dB) and x1000 (60dB) over a selectable bandwidths of 100Hz, 1kHz (HP), 3kHz, 30kHz, 100kHz and 1MHz (7000 model only). Noise referred to input is 7nV√Hz and common mode rejection is >100dB at 1kHz. Momentary pushbutton switches are provided that control coupling, bandwidth, gain and channel on/off selections. BNC connectors are provided for single-ended and differential input, ac output, and dc output (optional) connections.
-
Product
Sound Level Meters
-
A sound level meter is a measuring instrument used to assess noise or sound levels by measuring sound pressure. Often referred to as a sound pressure level (SPL) meter, decibel (dB) meter, noise meter or noise dosimeter, a sound level meter uses a microphone to capture sound. The sound is then evaluated within the sound level meter and acoustic measurement values are shown on the display of the sound level meter. The most common unit of acoustic measurement for sound is the decibel (dB); however, some sound level meter devices also determine the equivalent continuous sound level (Leq) and other acoustic parameters. With a portable sound level meter, industrial hygiene and workplace safety professionals can measure sound levels in multiple locations to ensure environmental conditions fall within recommended exposure limits (RELs). Some sound level meter devices can be permanently installed for continuous monitoring of sound levels at a work or job site.
-
Product
4-Channel 200 MHz A/D with DDC, Kintex UltraScale FPGA - XMC
Model 71861
-
- Jade Xilinx Kintex UltraScale FPGA Products and Navigator Design Suite Software Video- Jade Xilinx Kintex UltraScale FPGA Family Brochure- Complete radar and software radio interface solution- Supports Xilinx Kintex UltraScale FPGAs- Four 200 MHz 16-bit A/Ds- Four multiband DDCs (digital downconverters)- 5 GB of DDR4 SDRAM- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multimodule synchronization- PCI Express (Gen. 1, 2 & 3) interface up to x8- VITA 42.0 XMC compatible with switched fabric interfaces- Optional LVDS and gigabit serial connections to the FPGA for custom I/O- Ruggedized and conduction-cooled versions available- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
Functional/Protocol Debug and Analysis Reference Solution
DDR4
-
Highest confidence in measurement accuracy! Industry’s fastest triggering and data capture for DDR4 analysis, test, and debug.
-
Product
Regeneration Station
-
This equipment is a stand-alone device that enables to coherently regenerate an optical signal allowing long-haul dissemination of an ultra-stable optical frequency reference. Its architecture is based on the heterodyne phase-locking of a narrow spectral width laser diode on the reference signal. The station is equipped with low phase noise optical interferometer that perform a thorough characterization of the phase noise accumulated by the incoming signal, and a compensation system of this phase noise.
-
Product
FASTCAM
1MP and 2MP Cameras
-
A leading line of high-speed, slow-motion cameras manufactured by Photron. The "1MP" and "2MP" designations refer to the cameras' image sensor resolutions, which are used to capture ultra-fast events at thousands of frames per second
-
Product
Gas Filter Correlation Carbon Monoxide Analyzer
Model T300
-
The Model T300 measures low ranges of carbon monoxide by comparing infrared energy absorbed by a sample to that absorbed by a reference gas according to the Beer-Lambert law. Using a Gas Filter Correlation Wheel, a high energy IR light source is alternately passed through a CO filled chamber and a chamber with no CO present. The light path then travels through the sample cell, which has a folded path of 14 meters. The energy loss through the sample cell is compared with the span reference signal provided by the filter wheel to produce a signal proportional to concentration, with little effect from interfering gases within the sample. This design produces excellent zero and span stability and high signal to noise ratio, allowing extreme sensitivity. All T Series instruments offer an advanced color display, capacitive touch screen, intuitive user interface, flexible I/O, and built-in data acquisition capability. All instrument set up, control and access to stored data and diagnostic information, is available through the front panel, or via RS232, Ethernet, or USB com ports, either locally or by remote connection.The Model T300 comes with NumaView™ Software. NumaView™ Remote PC Software allows for a remote connection with virtual interface and data downloading capability to analyzers operating NumaView™ Software.
-
Product
Clock Oscillators
-
A crystal clock oscillator (sometimes referred to as a 'Standard Packaged Crystal Oscillator' or SPXO) is a 'plug and play' quartz crystal. It combines a quartz crystal resonator with an oscillator circuit in a single package to provide a fully functioning stand-alone oscillator circuit.
-
Product
Multifunctional Safety Tests
-
Manufacturers of electrical or electronic products are required by law to carry out an electrical safety test before placing them on the market. This final test takes place at the end of the manufacturing process and is therefore also referred to as an EOL test (end-of-line). Depending on the prescribed standard and directive, the following parameters are tested:- Leakage current and discharge current- Insulation resistance or the insulation strenth- Dielectric strength or electric strength- Correct installation of the protective conductor (ground continuity and ground bond test)- Faultless functioning of the product under the conditions defined for intended use (function or run test
-
Product
Measurement Of Straightness, Flatness, Positioning Uncertainty Of Round Tables
RTM - Measurement Of Positioning Uncertainty Of Indexing Tables
-
Optik Elektronik Gerätetechnik GmbH
RTM is a software for the measurement of positioning uncertainty of indexing tables using an electronic autocollimator and a polygon mirror as angle reference.
-
Product
Mid-Range Gas Filter Correlation Carbon Dioxide Analyzer
Model T360M
-
The Model T360M CO2 analyzer measures Carbon Dioxide by comparing infrared energy absorbed by a sample to that absorbed by a reference gas according to the Beer-Lambert law. Using a Gas Filter Correlation Wheel, a high-energy IR light source is alternately passed through a CO2 filled chamber and a chamber with no CO2 present. The light path then travels through the sample cell, which has a folded path of 1.28 meters.The energy loss through the sample cell is compared with the reference signal provided by the filter wheel to produce a signal proportional to concentration, with little effect from interfering gases within the sample. This design produces excellent zero and span stability and high signal to noise ratio, allowing excellent performance over a wide concentration range, making this instrument an ideal choice for CO2 reporting requirements associated with dilution CEMS.All T Series instruments offer an advanced color display, capacitive touch screen, intuitive user interface, flexible I/O, and built-in data acquisition capability. All instrument set up, control and access to stored data and diagnostic information is available through the front panel, or via RS232, Ethernet, or USB com ports, either locally or by remote connection.The Model T360M comes with NumaView™ Software. NumaView™ Remote PC Software allows for a remote connection with virtual interface and data downloading capability to analyzers operating NumaView™ Software.
-
Product
4 Serial Communication Channels, Programmable RS-232/422/485, Non-Isolated
SC6
-
Serial Communication Module SC6 provides up to 4 high-speed, programmable RS-232/422/485, individually non-isolated communication channels. Each channel is programmable for either RS-422/485 (differential, DF) or RS-232 (single ended, SE) hardware level interfaces. Individual channel non-isolated returns are available as part of the channel user interface signal set (for SE or SYS-GND reference).
-
Product
Reference Temperature Sensors
-
AMETEK Sensors, Test & Calibration
Our reference sensors can be used as your daily working-reference sensors in laboratory or field calibration applications. A large selection of types are available, including; straight, 90 degree angle, 4 mm or 1/4”. The superior design and specifications combined with a long history of reliability and low drift have made the STS probes the working-standard in many EN/IEC 17025 accredited laboratories worldwide. The DLC sensors are a part of our patented Dynamic Load Compensation system.
-
Product
Frequency Standards
-
Precision Test manufacturers a complete range of frequency standards. This includes rubidium and OXCO models either free running or controlled by an external reference (GPS, GLONASS, Galileo, 1pps, 5 MHz, 10 MHz, IRIG-B etc). Output frequencies typically 1 MHz, 5 MHz, 10 MHz, 10.23 MHz, 13 MHz, 100 MHz or bespoke frequency.
-
Product
68-Pin D-SUB Female to 68-Pin D-SUB Female, Twisted Pair, Shielded Multifunction Cable
199006-0R5
Multifunction Cable
The SH68F-68F-EPM Cable, sometimes referred to as SH68-68-EPM, connects NI DAQ 68-pin devices to 68-pin accessories. The SH68F-68F-EPM Cable features D-type connectors and it is available in different lengths.
-
Product
IQ Demodulator
IQD Series
-
*Capable of receiving RF and LO frequency inputs *Output from DC to 500 MHz *Internal low noise oscillator Internal reference *Buffered demodulator *Balanced IQ *Optimized for low EVm *Optional internal Reference Detect Switch (EM Research RDS Series) *Up to 250 mega-symbols per second
-
Product
1-Pin BNC (Male Or Female) To 1-Pin SMB Female, 50 Ω Coaxial Cable
778827-01
Coaxial Cable
The SMB-BNC Coaxial Cable, sometimes referred to as SMB-100 or SMB-110, connects measurement and signal devices. This cable is available in different lengths and quantities.
-
Product
1-Pin BNC Male to 1-Pin BNC Male Coaxial Cable
781887-01
Coax Patchcord
The BNC-BNC Coaxial Cable, sometimes referred to as BNC Plug to BNC Plug, connects measurement and signal devices.
-
Product
Reference Electrodes
-
PotentioLab reference electrodes provide stable potential control for three-electrode electrochemical testing. Options include Ag/AgCl reference electrodes and laboratory designs for aqueous systems, salt bridge use and compatible custom electrochemical cells.
-
Product
Reference Coordinate Measuring Machine
XENOS
-
XENOS from ZEISS features two linear drives in the Y direction, which are synchronized via a new technology developed by ZEISS: the central drive. It ensures optimal force distribution of the drives depending on the position of the X axis.
-
Product
Capacitance Standard Frame
AH 1100
-
The AH 1100 capacitance standard frame containing from one to four AH 11A fused-silica capacitance standards provides reference capacitors of unexcelled stability. The inherent stability of this system when subjected to mechanical or thermal shock makes it the ideal transfer standard for capacitance. The built-in precision temperature controllers make it a simple, reliable system to use.
-
Product
Mid-Range Gas Filter Correlation CO2 Analyzer
Model N360M
-
Teledyne Advanced Pollution Instrumentation
The Model N360M measures carbon dioxide (CO2) by comparing infrared energy absorbed by a sample to that absorbed by a reference according to the Beer-Lambert law.The N360M uses Gas Filter Correlation (GFC) to overcome the interfering effects of various other gases (such as water vapor) that also absorb IR. The analyzer passes the IR beam through a spinning wheel made up of two separate chambers: one containing a high concentration of CO2 known as the reference, and the other containing a neutral gas known as the measure. The concentration of CO2 in the sample chamber is computed by taking the ratio of the instantaneous measure and reference values and then compensating the ratio for sample temperature and pressure. A nitrogen purge system is provided for the GFC wheel assembly to eliminate the effects of ambient CO2, if necessary.
-
Product
Solar Cell I-V Characterization System
VS6821
-
Industrial Vision Technology Pte Ltd.
This system provides cell manufactures and laboratories a new way in testing and measuring photovoltaic cells. Integrated with Steady-State Solar Simulator, it provides complete coverage of testing parameters and measurement requirements by most international standards. Its test methods, procedure & equipment are IEC 60904 compliant. Calibration of reference cell is performed at Fraunhofer ISE in Germany, and is traceable to PTB.
