Showing results: 1591 - 1605 of 5298 items found.
-
Teledyne Marine RD Instruments
Go straight to work collecting highly accurate stream and river discharge data with the RiverRay Acoustic Doppler Current Profiler (ADCP).
-
EMC Partner AG
Impulse generators with current and voltage outputs for testing complex Surge Protection Devices comprising combinations of varistors, gas arrestors and resistors
-
MS-139 -
Misum Systech Co., Ltd.
This equipment is used for inspecting the current, voltage and temperature of Smart Module in lap top battery. It can do EEPROM data read / verify.
-
YAVAL022 -
6TL Engineering
5x (1×4) Mux + 2x Pass trough Selftest function 30Vac/dc, 10W Max Max current 500mA Reflexive
-
AYA-Instruments
can enclose conductors up to (50mm) 0.968 inch and measure currents from 100mA to 1200A*. They are a reliable and economic solution for common applications.
-
16494A -
Keysight Technologies
16494A is suitable for low current applications down to the sub fA level. It supports a maximum voltage/current of 200 V / 1A DC.
-
BV9201B -
Keysight Technologies
The BenchVue Advanced power control app helps characterize voltage and current measurements and generate arbitrary waveforms for single instrument support.
-
CS Series -
AMETEK Programmable Power, Inc.
The CS Series represents an advanced AC current source that addresses increasing demands on manufacturers to test products using real-world current profiles. By combining true current transconductance amplifiers with an advanced digital controller and harmonic power analyzer, CS Series current sources are capable of performing tests that would traditionally have been difficult to accomplish.
-
6330A series -
Chroma ATE Inc.
The 6330A family offers 8 types of modular loads with power ranging from 30 watts to 1200 watts, current from 0.5mA to 240A, and voltage measurement from 0.5mV to 500V. Each load is isolated and floating, programmable in dual current range and measuring voltage range, and capable of synchronizing with other modules for control operating. The load can be operated in constant current, constant voltage, and constant resistance. With Synchronic parallel control capability, 6330A series loads allow users to parallel and synchronize more than one load together from an internal loading control signal. This feature provides synchronic dynamic loading test for multi-output power and high power test solution. Real time measurement of voltage, current, is integrated into each 6330A load module using a 16-bit precision measurement circuit. The user can perform on line voltage measurement and adjustment, or simulate short circuit test using the simple keypad on the front panel.
-
CAEN S.p.A.
- From 12 to 48 independently controllable High Voltage channels- 0 ÷ 1.5 kV (A1538D) and 0 ÷ 1/1.3/1.4 kV output voltage (A1515B)- Maximum Current 10 mA, 0.1 or 1/0.1, 3/0.3 mA (dual range boards)- Radiall Multipin, SHV or DB37 connectors- Available with either positive or negative polarity (A1538D and A7038)- Up to 2 nA / 100 pA current set / monitor resolution- Up to 20 mV / 2 mV voltage set / monitor resolution- Very low ripple, down to < 5 mVpp- 3 different channel grounding - Common Ground (AGxxxx) - Common Floating Return (Axxxx) - Full Floating (A1515B only)- Independently programmable for each channel: - Output voltage - Current limit - Ramp up/down - TRIP parameter- Current generator operation in overcurrent condition- Specific design for GEM and Vertex detector and dedicatedaccessories (A1515B boards only)
-
MCH Instruments Co.,Ltd.
Features:*High voltage,small current provides high accuracy.*Leakage Current and Test Time continuously adjustable.*Display Time,Voltage and Current simultaneously.*High voltage breakdown protection.*Over limit sound-light alarm
-
MT322-107 -
ALTINEX, Inc.
The MT322-107 distributes AC power from a single AC source to multiple AC outlets. These outlets can be connected to any type of audio/video equipment. The total current supplied to all outlets must be less than 10 A. Built-in sensors alert the user by flashing the LEDs when the load exceeds 8.5 A and a warning message is sent to the RS-232 bus when the current draw is near maximum.
-
SERIES LMP
60 -
Test Connections Inc.
MechanicalMINIMUM CENTERS: .100 (2.54)FULL TRAVEL: .160 (4.06)WORKING TRAVEL: .107 (2.72)OPERATING LIFE: 1,000,000 cyclesElectricalMAXIMUM CURRENT: 5 amps continuousat working travel, non-inductiveRESISTANCE: At 35 mA test current,35 mOHMS meanMaterials and FinishesPLUNGER: Heat treated berylliumcopper, 24 Kt gold plated over nickelBARREL: Nickel silver, 24 Kt goldplated over nickel
-
Texas Co.
Probes connect the input of the oscilloscope to test points on the device under test (DUT). There are many types, including: high impedance passive, low capacitance, single-ended active, differential active, high voltage, and current probes. This is the first in a series of three articles on probe selection and application, and will focus on passive probes. Part 2 and part 3 will address active probes and current probes, respectively.
-
Ametek Scientific Instruments
Potentiostats control a voltage and measure a resulting current. The Control Amplifier outputs power to the counter electrode (also called auxiliary electrode). A feedback loop is established to control the cell potential between the reference and working electrode. This voltage is measured by the input electrometer, that has a high impedance. This current is then measured between the working and counter electrodes while this potential is maintained at the working electrode and reference electrode.