Showing results: 3031 - 3045 of 3660 items found.
-
Tenmars Electronics Co., Ltd.
*3-1/2 digit LCD display with maximum reading of 2000.*Overload indication.*Low battery indication.*Measures high insulation resistance manual range: 0.1MΩ to 2000MΩ*250V: 0.1MΩ to 200MΩ.*500V: 0.1MΩ to 200MΩ.*1000V: 1MΩ to 2000MΩ.*Measures AC 0 to 750V and DC voltages 0V to 1000V.*Function Keys: Data Hold, Max.*Continuity Test.
-
PJ Electronics, Inc.
PJ Electronics offers a wide selection of models from which to choose! Basically, you may custom order a tester to meet your specific needs. PJ Electronics manufactures 12 lines of Bench, Portable & Console Model Digital High Frequency Surge / DC Hi-Pot Testers. 220-240 operating line voltage is available upon request and for an additional cost.
-
Extech VT30 -
Extech Instruments Corporation
The VT30 is a voltage, continuity and phase tester with built in flashlight and backlit digital display with bar graph. The tester features a double molded IP64 housing, polarity detection with LEDs for positive and negative DC and a CAT III 600 Volt / CATIV 600 Volt safety rating. This product is complete with a one year warranty, 2 AAA batteries, protective cap, and pouch case.
-
448 -
SCI
Our 448 model is a 4-in-1 tester with 500VA AC Hipot, DC Hipot, Insulation Resistance and Ground Bond testing capabilities. The 448 is capable of a 500VA AC Hipot output to comply with 100mA leakage current test compliance requirements. This tester features a simple design and easy-to-use interface, reducing setup time and increasing production-line throughput for your application.
-
779600-02 -
NI
The NI-9485 allows for direct connection to a wide array of industrial devices such as motors, actuators, and DC devices. Each channel provides access to a solid state relay (SSR) for switching voltages up to 60 VDC/30 Vrms with switching current up to 750 mA per channel or up to 1.2 A on four channels. Each channel also features channel-to-channel isolation.
-
779600-01 -
NI
The NI-9485 allows for direct connection to a wide array of industrial devices such as motors, actuators, and DC devices. Each channel provides access to a solid state relay (SSR) for switching voltages up to 60 VDC/30 Vrms with switching current up to 750 mA per channel or up to 1.2 A on four channels. Each channel also features channel-to-channel isolation.
-
Spectrum Instrumentation
The Arbitrary Waveform Generator (AWG) is a powerful and flexible signal generator capable of outputting any wave shape within the bandwidth of the generator.Every AWG provides the ability to use it as a simple function generator. This allows creation and output of sine, rectangular (square), triangle, saw tooth, and DC waveforms directly without any complex operations.Details on the generation of Waveform can be found in separate articles:
-
N8758A -
Keysight Technologies
Keysight basic DC power supplies offer essential features for a tight budget. The Keysight N8758A is an 80 V, 65 A, 5,200 W, single-output power supply in a small 2U package. It offers flexible AC input options, analog / resistance control of output voltage and current, and parallel and series connection of multiple supplies to achieve more output current or voltage.
-
N8736A -
Keysight Technologies
Keysight basic DC power supplies offer essential features for a tight budget. The Keysight N8736A is a 40V, 85A, 3300W single output power supply in a small 2U package. It offers flexible AC input options, analog / resistance control of output voltage and current as well as parallel and series connection of multiple supplies to achieve more output current or voltage respectively.
-
M9135A -
Keysight Technologies
The M9135A is a general purpose switch with 20 independent, single-pole, single-throw (Form A) switches in a single PXI module. This module is ideal for switching heavy loads or power supplies including voltages mains or DC current. The heavy-duty armature relays are rated for up to 5A and 300W, enough for inductive or capacitive loads. Choose from the heavy-duty power connector or an unterminated power cable.
-
USB-2405 -
ADLINK Technology Inc.
The USB-2405 is a 24-bit high-performance dynamic signal acquisition USB module equipped with 4 analog input channels providing simultaneous-sampling at up to 128 kS/s per channel. The USB-2405 also features software selectable AC or DC coupling input configuration and built-in high precision 2 mA excitation current to measure integrated electronic piezoelectric (IEPE) sensors such as accelerometers and microphones.
-
SD750250G -
Zhejiang Sandi Electric Co., Ltd
AC-DC Power Rectifier Battery Charger Customized for Lead Acid AGM Gel LiFePO4 Lithium Battery is for DC battery system charging station. With single-phase or 3 phase non neutral conductor AC input, it has the advantages of high efficiency, high power density and low harmonic. 50-750Vdc output voltage range optional, suitable for all types of batteries.
-
M Model -
PJ Electronics, Inc.
Portable compact Multi-Operational Surge Tester that contains a multi-position carrying/tilt handle and a rear plastic snap-on cover for cable storage and transportation in the shop or field. The "M" is the perfect choice for your complete preventive/predictive maintenance testing - DC Hi-Pot testing, handheld resistance meter* testing and the capability of testing fully assembled grounded motors without rotating the rotor position.
-
MB Model -
PJ Electronics, Inc.
Bench all-in-one versatile Multi-Operational Surge Tester that you need for all of your electrical insulation testing. The Hi-Pot tester has separate L.E.D. panel meters for direct readout (voltage and leakage current) so that no interpolation on the scopes display is ever needed. This MOST can surge test extremely low inductance windings, DC armatures, etc.
-
PA-330Z -
Ono Sokki
The PA-330Z receives the square wave signals from the rotary encoder, and converts it to low impedance signals suitable for long distance transmission after wave-shaping and amplifying via photo couplers which provide isolation between input and output.A 12VDC external power supply is provided for use with the DC powered RP series encoder.The case is sealed construction which allows closely mounting to the encoder.